scholarly journals Numerical Analysis of the Activated Combustion High-Velocity Air-Fuel Spraying Process: A Three-Dimensional Simulation with Improved Gas Mixing and Combustion Mode

Materials ◽  
2021 ◽  
Vol 14 (3) ◽  
pp. 657
Author(s):  
Fuqiang Liu ◽  
Zhiyong Li ◽  
Min Fang ◽  
Hua Hou
Keyword(s):  
Combustion Chamber ◽  
High Velocity ◽  
Gas Flow ◽  
Porous Ceramic ◽  
Flame Temperature ◽  
Three Dimensional ◽  
Vital Role ◽  
Rectification Effect ◽  
Turbulent Dissipation ◽  
Spraying Process

Owing to its low flame temperature and high airflow velocity, the activated combustion high-velocity air-fuel (AC-HVAF) spraying process has garnered considerable attention in recent years. Analyzing the velocity field, temperature field, and composition of AC-HVAF spray coatings plays a vital role in improving the quality of coatings. In this study, an actual spray gun is adopted as a prototype, and the radial air inlets are introduced to improve the reaction efficiency so that the chemical reaction can be completed in the combustion chamber. Furthermore, a complete three-dimensional (3D) model is established to examine the effects of radial inlets and porous ceramic sheet on the combustion and flow fields. The hexahedral cells are used to discretize the entire model for reducing the influence of false-diffusion on the calculation results. The gas flow field is simulated by the commercial Fluent software, and the results indicate that the porous ceramic sheet effectively reduces the turbulent dissipation of the airflow with a good rectification effect (the ceramic sheet ensures a consistent airflow direction). The radial inlets and the porous ceramic sheet promote the formation of vortex in the combustion chamber, increase the residence time and stroke of the gas in the combustion chamber, and improve the probability of chemical reactions. In addition, it is observed that the stability of velocity for the airflow is strongly related to the airflow density.

scholarly journals Design and development of combustion chambers for gas turbine engines based on calculations of various levels of complexity

2021 ◽  
Vol 20 (3) ◽  
pp. 7-23
Author(s):  
Y. B. Aleksandrov ◽  
T. D. Nguyen ◽  
B. G. Mingazov
Keyword(s):  
Combustion Chamber ◽  
Gas Turbine ◽  
Gas Flow ◽  
Combustion Process ◽  
Three Dimensional ◽  
Numerical Calculations ◽  
Turbine Engines ◽  
Gas Turbine Engines ◽  
Combustion Chambers ◽  
Flame Tube

The article proposes a method for designing combustion chambers for gas turbine engines based on a combination of the use of calculations in a one-dimensional and three-dimensional formulation of the problem. This technique allows you to quickly design at the initial stage of creating and development of the existing combustion chambers using simplified calculation algorithms. At the final stage, detailed calculations are carried out using three-dimensional numerical calculations. The method includes hydraulic calculations, on the basis of which the distribution of the air flow passing through the main elements of the combustion chamber is determined. Then, the mixing of the gas flow downstream of the flame tube head and the air passing through the holes in the flame tube is determined. The mixing quality determines the distribution of local mixture compositions along the length of the flame tube. The calculation of the combustion process is carried out with the determination of the combustion efficiency, temperature, concentrations of harmful substances and other parameters. The proposed method is tested drawing on the example of a combustion chamber of the cannular type. The results of numerical calculations, experimental data and values obtained using the proposed method for various operating modes of the engine are compared.

scholarly journals Effects of Mesh Generation on Modelling Aluminium Anode Baking Furnaces

Fluids ◽  
2021 ◽  
Vol 6 (4) ◽  
pp. 140
Author(s):  
Jose Libreros ◽  
Maria Trujillo
Keyword(s):  
Velocity Field ◽  
Turbulent Flow ◽  
Gas Flow ◽  
Turbulent Viscosity ◽  
Three Dimensional ◽  
Carbon Anode ◽  
Geometrical Parameters ◽  
Operational Parameters ◽  
Turbulent Dissipation ◽  
Flow Models

Anode baking is critical in carbon anode production for aluminium extraction. Operational and geometrical parameters have a direct impact on the performance of anode baking furnaces (ABF), and hence on the resulting anode quality. Gas flow patterns, velocity field, pressure drop, shear stress and turbulent dissipation rate are the main operational parameters to be optimised, considering a specific geometry that is discretised as a mesh. Therefore, this paper aims to establish the need to generate an appropriate mesh to perform accurate numerical simulations of three-dimensional turbulent flow in a single section of an ABF. Two geometries are considered for generating three meshes, using COMSOL and cfMesh, with different refinement zones. The three meshes are used for creating nine incompressible isothermal turbulent flow models, with varying operational parameters. Velocity field, convergence and turbulent viscosity ratio in the outlet of fuel inlet pipes are the quantification criteria. Quantification criteria have shown that a better physical representation is obtained by refining in the whole combustion zone. COMSOL Multiphysics’ built-in mesh generator allows quadrilateral, tetrahedron and hexahedron shapes. Adaptive cell sizes and shapes have a place within modelling, since refining a mesh in appropriate zones brings the Peclet number down when the incompressible isothermal turbulent flow is simulated.

A 3D Model of Combustion in Large-Scale Circulating Fluidized Bed Boilers

2004 ◽  
Vol 2 (1) ◽  
Author(s):  
Karsten Luecke ◽  
Ernst-Ulrich Hartge ◽  
Joachim Werther
Keyword(s):  
Combustion Chamber ◽  
Fluidized Bed ◽  
Large Scale ◽  
Gas Flow ◽  
Circulating Fluidized Bed ◽  
Combustion Process ◽  
Three Dimensional ◽  
Three Dimensional Model ◽  
Cross Sectional ◽  
Secondary Air

In a circulating fluidized bed (CFB) combustor the reacting solids are locally fed into the combustion chamber. These reactants have to be dispersed across the reactor's cross-sectional area. Since the rate of mixing is limited this leads to a mal-distribution of the reactants and to locally varying reaction conditions. In order to describe the influence of mixing a three-dimensional model of the combustion chamber is suggested. The model is divided into three sub-topics. First, the flow structure in terms of local gas and solids velocities and solids volume concentrations is described. Second, mixing of the solids and the gas phase is quantified by defining dispersion coefficients, and finally the combustion process itself, i.e. the reaction kinetics, is modelled. The model was validated against data from measurements in the large-scale combustor of Chalmers University of Technology in Göteborg/Sweden. Insufficient fuel mixing generated mal-distributions of locally released volatiles, which were the basis for the uneven reactants distribution at steady-state. In the case of two-stage operation, the injected secondary air did not reach immediately the reactor's center but was slowly mixed with the main gas flow. The concentration gradients hardly vanish before the exit of the combustion chamber.

Three-Dimensional reconstruction of isolated centrosomes by automated electron tomography

1994 ◽  
Vol 52 ◽  
pp. 310-311
Author(s):  
M.B. Braunfeld ◽  
M. Moritz ◽  
B.M. Alberts ◽  
J.W. Sedat ◽  
D.A. Agard
Keyword(s):  
Electron Tomography ◽  
Three Dimensional ◽  
Vital Role ◽  
Complex Nature ◽  
Animal Cells ◽  
Microtubule Organizing Center ◽  
Nucleation Sites ◽  
Dimensional Reconstruction ◽  
Organizing Center ◽  
Resolution Model

In animal cells, the centrosome functions as the primary microtubule organizing center (MTOC). As such the centrosome plays a vital role in determining a cell's shape, migration, and perhaps most importantly, its division. Despite the obvious importance of this organelle little is known about centrosomal regulation, duplication, or how it nucleates microtubules. Furthermore, no high resolution model for centrosomal structure exists.We have used automated electron tomography, and reconstruction techniques in an attempt to better understand the complex nature of the centrosome. Additionally we hope to identify nucleation sites for microtubule growth.Centrosomes were isolated from early Drosophila embryos. Briefly, after large organelles and debris from homogenized embryos were pelleted, the resulting supernatant was separated on a sucrose velocity gradient. Fractions were collected and assayed for centrosome-mediated microtubule -nucleating activity by incubating with fluorescently-labeled tubulin subunits. The resulting microtubule asters were then spun onto coverslips and viewed by fluorescence microscopy.

Real gas flow fields about three dimensional configurations

1983 ◽  
Author(s):  
A. BALAKRISHNAN ◽  
C. LOMBARD ◽  
W.C. DAVY
Keyword(s):  
Gas Flow ◽  
Three Dimensional ◽  
Flow Fields ◽  
Real Gas

scholarly journals Modeling of three-dimensional exciplex pumped fluid Cs vapor laser with transverse and longitudinal gas flow

2021 ◽  
Vol 9 ◽  
Author(s):  
Chenyi Su ◽  
Xingqi Xu ◽  
Jinghua Huang ◽  
Bailiang Pan
Keyword(s):  
Wall Temperature ◽  
Laser Power ◽  
Gas Flow ◽  
Particle Density ◽  
Fluid Velocity ◽  
Three Dimensional ◽  
Heat Accumulation ◽  
Vapor Laser ◽  
Output Laser Power ◽  
Output Laser

Abstract Considering the thermodynamical fluid mechanics in the gain medium and laser kinetic processes, a three-dimensional theoretical model of an exciplex-pumped Cs vapor laser with longitudinal and transverse gas flow is established. The slope efficiency of laser calculated by the model shows good agreement with the experimental data. The comprehensive three-dimensional distribution of temperature and particle density of Cs is depicted. The influence of pump intensity, wall temperature, and fluid velocity on the laser output performance is also simulated and analyzed in detail, suggesting that a higher wall temperature can guarantee a higher output laser power while causing a more significant heat accumulation in the cell. Compared with longitudinal gas flow, the transverse flow can improve the output laser power by effectively removing the generated heat accumulation and alleviating the temperature gradient in the cell.

scholarly journals Polymer cyclization for the emergence of hierarchical nanostructures

2021 ◽  
Vol 12 (1) ◽  
Author(s):  
Chaojian Chen ◽  
Manjesh Kumar Singh ◽  
Katrin Wunderlich ◽  
Sean Harvey ◽  
Colette J. Whitfield ◽  
...  
Keyword(s):  
Self Assembly ◽  
Three Dimensional ◽  
Hierarchical Structures ◽  
Structural Similarity ◽  
Vital Role ◽  
Nanomaterial Synthesis ◽  
Wide Range ◽  
Linear Poly ◽  
Polymer Folding ◽  
Dynamics Simulations

AbstractThe creation of synthetic polymer nanoobjects with well-defined hierarchical structures is important for a wide range of applications such as nanomaterial synthesis, catalysis, and therapeutics. Inspired by the programmability and precise three-dimensional architectures of biomolecules, here we demonstrate the strategy of fabricating controlled hierarchical structures through self-assembly of folded synthetic polymers. Linear poly(2-hydroxyethyl methacrylate) of different lengths are folded into cyclic polymers and their self-assembly into hierarchical structures is elucidated by various experimental techniques and molecular dynamics simulations. Based on their structural similarity, macrocyclic brush polymers with amphiphilic block side chains are synthesized, which can self-assemble into wormlike and higher-ordered structures. Our work points out the vital role of polymer folding in macromolecular self-assembly and establishes a versatile approach for constructing biomimetic hierarchical assemblies.

Sign in / Sign up

Export Citation Format

Share Document