scholarly journals Cyclic Deformation Induced Residual Stress Evolution and 3D Short Fatigue Crack Growth Investigated by Advanced Synchrotron Tomography Techniques

Materials ◽  
2021 ◽  
Vol 14 (6) ◽  
pp. 1562
Author(s):  
Benjamin Dönges ◽  
Melanie Syha ◽  
Anne K. Hüsecken ◽  
Ullrich Pietsch ◽  
Wolfgang Ludwig ◽  
...  
Keyword(s):  
Fatigue Crack ◽  
Fatigue Crack Growth ◽  
Residual Stresses ◽  
Crack Propagation ◽  
Crack Growth ◽  
Cyclic Deformation ◽  
Phase Contrast ◽  
Crack Nucleation ◽  
Short Fatigue Crack ◽  
Phase Contrast Tomography

Diffraction and phase contrast tomography techniques were successfully applied to an austenitic–ferritic duplex stainless steel representing exemplarily a metallic material containing two phases with different crystal structures. The reconstructed volumes of both phases were discretized by finite elements. A crystal plasticity finite-element analysis was executed in order to simulate the development of the experimentally determined first and second order residual stresses, which built up due to the manufacturing process of the material. Cyclic deformation simulations showed the single-grain-resolved evolution of initial residual stresses in both phases and were found to be in good agreement with the experimental results. Solely in ferritic grains, residual stresses built up due to cyclic deformation, which promoted crack nucleation in this phase. Furthermore, phase contrast tomography was applied in order to analyze the mechanisms of fatigue crack nucleation and short fatigue crack propagation three-dimensionally and nondestructively. The results clearly showed the significance of microstructural barriers for short fatigue crack growth at the surface, as well as into the material. The investigation presented aims for a better understanding of the three-dimensional mechanisms governing short fatigue crack propagation and, in particular, the effect of residual stresses on these mechanisms. The final goal was to generate tailored microstructures for improved fatigue resistance and enhanced fatigue life.

scholarly journals Short fatigue crack growth in welded joints described by the effective cyclic J-integral

2018 ◽  
Vol 165 ◽  
pp. 09002
Author(s):  
Désiré Tchoffo Ngoula ◽  
Michael Vormwald
Keyword(s):  
Fatigue Crack ◽  
Fatigue Life ◽  
Fatigue Crack Growth ◽  
Residual Stresses ◽  
Crack Growth ◽  
Welded Joints ◽  
Driving Force ◽  
J Integral ◽  
Crack Driving Force ◽  
Short Fatigue Crack

The purpose of the present contribution is to predict the fatigue life of welded joints by using the effective cyclic J-integral as crack driving force. The plasticity induced crack closure effects and the effects of welding residual stresses are taken into consideration. Here, the fatigue life is regarded as period of short fatigue crack growth. The node release technique is used to perform finite element based crack growth analyses. For fatigue lives calculations, the effective cyclic J-integral is employed in a relation similar to the Paris (crack growth) equation. For this purpose, a specific code was written for the determination of the effective cyclic J-integral for various lifetime relevant crack lengths. The effects of welding residual stresses on the crack driving force and the calculated fatigue lives are investigated. Results reveal that the influence of residual stresses can be neglected only for large load amplitudes. Finally, the predicted fatigue lives are compared with experimental data: a good accordance between both results is achieved.

Effect of Hardness and Tensile Mean Stress on Fatigue Crack Growth in Beryllium Copper

1969 ◽  
Vol 11 (3) ◽  
pp. 343-349 ◽  
Author(s):  
L. P. Pook
Keyword(s):  
Growth Rate ◽  
Fatigue Crack ◽  
Crack Growth Rate ◽  
Fatigue Crack Growth ◽  
Residual Stresses ◽  
Crack Growth ◽  
Fatigue Crack Growth Rate ◽  
Mean Stress ◽  
Growth Data ◽  
Beryllium Copper

Some fatigue crack growth data have been obtained for age-hardened beryllium copper. The fatigue crack growth rate was found to be very dependent on the hardness and tensile mean stress. This dependence is believed to be associated with the intense residual stresses surrounding Preston-Guinier zones.

Modeling of Fatigue Crack Propagation

2004 ◽  
Vol 126 (1) ◽  
pp. 77-86 ◽  
Author(s):  
Yanyao Jiang ◽  
Miaolin Feng
Keyword(s):  
Fatigue Crack ◽  
Fatigue Crack Growth ◽  
Crack Initiation ◽  
Crack Propagation ◽  
Crack Growth ◽  
Fatigue Damage ◽  
Fatigue Crack Propagation ◽  
Fatigue Crack Initiation ◽  
Cyclic Plasticity ◽  
R Ratio

Fatigue crack propagation was modeled by using the cyclic plasticity material properties and fatigue constants for crack initiation. The cyclic elastic-plastic stress-strain field near the crack tip was analyzed using the finite element method with the implementation of a robust cyclic plasticity theory. An incremental multiaxial fatigue criterion was employed to determine the fatigue damage. A straightforward method was developed to determine the fatigue crack growth rate. Crack propagation behavior of a material was obtained without any additional assumptions or fitting. Benchmark Mode I fatigue crack growth experiments were conducted using 1070 steel at room temperature. The approach developed was able to quantitatively capture all the important fatigue crack propagation behaviors including the overload and the R-ratio effects on crack propagation and threshold. The models provide a new perspective for the R-ratio effects. The results support the notion that the fatigue crack initiation and propagation behaviors are governed by the same fatigue damage mechanisms. Crack growth can be treated as a process of continuous crack nucleation.

Pre-Strain Effects on Mixed-Mode Fatigue Crack Propagation Behaviour of the P355NL1 Pressure Vessels Steel

2018 ◽  
Author(s):  
João Ferreira ◽  
José A. F. O. Correia ◽  
Grzegorz Lesiuk ◽  
Sergio Blasón González ◽  
Maria Cristina R. Gonzalez ◽  
...  
Keyword(s):  
Plastic Deformation ◽  
Fatigue Crack ◽  
Fatigue Crack Growth ◽  
Crack Propagation ◽  
Crack Growth ◽  
Fatigue Crack Propagation ◽  
Mixed Mode ◽  
Pressure Vessels ◽  
Mode I ◽  
Pure Mode

Pressure vessels and piping are commonly subjected to plastic deformation during manufacturing or installation. This pre-deformation history, usually called pre-strain, may have a significant influence on the resistance against fatigue crack growth of the material. Several studies have been performed to investigate the pre-strain effects on the pure mode I fatigue crack propagation, but less on mixed-mode (I+II) fatigue crack propagation conditions. The present study aims at investigating the effect of tensile plastic pre-strain on fatigue crack growth behavior (da/dN vs. ΔK) of the P355NL1 pressure vessel steel. For that purpose, fatigue crack propagation tests were conducted on specimens with two distinct degrees of pre-strain: 0% and 6%, under mixed mode (I+II) conditions using CTS specimens. Moreover, for comparison purposes, CT specimens were tested under pure mode I conditions for pre-strains of 0% and 3%. Contrary to the majority of previous studies, that applied plastic deformation directly on the machined specimen, in this work the pre-straining operation was carried out prior to the machining of the specimens with the objective to minimize residual stress effects and distortions. Results revealed that, for the P355NL1 steel, the tensile pre-strain increased fatigue crack initiation angle and reduced fatigue crack growth rates in the Paris region for mixed mode conditions. The pre-straining procedure had a clear impact on the Paris law constants, increasing the coefficient and decreasing the exponent. In the low ΔK region, results indicate that pre-strain causes a decrease in ΔKth.

Fatigue Crack Growth Behavior of Autofrettaged Hydrogen Pressure Vessel Made of Low Alloy Steel

2017 ◽  
Author(s):  
Yoru Wada ◽  
Yusuke Yanagisawa
Keyword(s):  
High Pressure ◽  
Fatigue Crack ◽  
Fatigue Crack Growth ◽  
Crack Propagation ◽  
Crack Growth ◽  
Cylindrical Specimen ◽  
Growth Behavior ◽  
Gaseous Hydrogen ◽  
Crack Growth Behavior ◽  
Low Alloy Steel

Autofrettage is used to known as an effective method to prevent fatigue crack propagation of thick-walled cylinder vessels operating under high pressure. Since low-alloy steel shows an enhanced crack growth rate in high-pressure gaseous hydrogen, this paper aims to validate the effect of autofrettage on crack growth behavior in high-pressure gaseous hydrogen utilizing 4%NiCrMoV steel (SA723 Gr3 Class2). An autofrettaged cylindrical specimen with a 70mm inside diameter and 111mm outside diameter was prepared with an axial EDM (depth of 1mm) notched on the inside surface. The measured residual stress profile coincides well with the calculated results. The fatigue crack growth test was conducted by pressurizing the cylinder and varying the external water pressure. Crack propagation from the EDM notch was observed in the non-autofrettaged cylindrical specimen while no crack propagation was observed when the initial EDM notch size was within the compressive residual stress field. When the initial EDM notch size was increased, the fatigue crack growth showed a narrow, groove-like fracture surface for the autofrettaged specimen. In order to qualitatively analyze those results, fatigue crack growth rates were examined under various load ratios including a negative load ratio using a fracture mechanics specimen. From the information obtained, crack growth analysis of an autofrettaged cylinder in a high-pressure hydrogen environment was successfully demonstrated with a fracture mechanics approach.

Crack nucleation at forging flaws studied by non-local peridynamics simulations

2021 ◽  
pp. 108128652110572
Author(s):  
Mohammad Rezaul Karim ◽  
Kai Kadau ◽  
Santosh Narasimhachary ◽  
Francesco Radaelli ◽  
Christian Amann ◽  
...  
Keyword(s):  
Fatigue Crack ◽  
Fatigue Crack Growth ◽  
Crack Growth ◽  
Gas Turbines ◽  
Crack Nucleation ◽  
Rotor Steel ◽  
Nucleation Process ◽  
Metallic Oxide ◽  
Oxide Inclusions ◽  
Peridynamic Model

We present a computational study and framework that allows us to study and understand the crack nucleation process from forging flaws. Forging flaws may be present in large steel rotor components commonly used for rotating power generation equipment including gas turbines, electrical generators, and steam turbines. The service life of these components is often limited by crack nucleation and subsequent growth from such forging flaws, which frequently exhibit themselves as non-metallic oxide inclusions. The fatigue crack growth process can be described by established engineering fracture mechanics methods. However, the initial crack nucleation process from a forging flaw is challenging for traditional engineering methods to quantify as it depends on the details of the flaw, including flaw morphology. We adopt the peridynamics method to describe and study this crack nucleation process. For a specific industrial gas turbine rotor steel, we present how we integrate and fit commonly known base material property data such as elastic properties, yield strength, and S-N curves, as well as fatigue crack growth data into a peridynamic model. The obtained model is then utilized in a series of high-performance two-dimensional peridynamic simulations to study the crack nucleation process from forging flaws for ambient and elevated temperatures in a rectangular simulation cell specimen. The simulations reveal an initial local nucleation at multiple small oxide inclusions followed by micro-crack propagation, arrest, coalescence, and eventual emergence of a dominant micro-crack that governs the crack nucleation process. The dependence on temperature and density of oxide inclusions of both the details of the microscopic processes and cycles to crack nucleation is also observed. The results are compared with fatigue experiments performed with specimens containing forging flaws of the same rotor steel.

Sign in / Sign up

Export Citation Format

Share Document