scholarly journals Effect of Polyphenylsulfone and Polysulfone Incompatibility on the Structure and Performance of Blend Membranes for Ultrafiltration

Materials ◽  
2021 ◽  
Vol 14 (19) ◽  
pp. 5740
Author(s):  
Tatiana Plisko ◽  
Yana Karslyan ◽  
Alexandr Bildyukevich
Keyword(s):  
Phase Separation ◽  
Human Serum Albumin ◽  
Serum Albumin ◽  
Human Serum ◽  
Pure Water ◽  
Water Flux ◽  
Ultrafiltration Membranes ◽  
Casting Solution ◽  
Blend Membranes ◽  
Pure Water Flux

This study deals with the modification of polyphenylsulfone ultrafiltration membranes by introduction of an incompatible polymer polysulfone to the polyphenylsulfone casting solution to improve the permeability. The correlation between properties of the blend polyphenylsulfone/polysulfone solutions and porous anisotropic membranes for ultrafiltration prepared from these solutions was revealed. The blend polyphenylsulfone/polysulfone solutions were investigated using a turbidity spectrum method, optical microscopy and measurements of dynamic viscosity and turbidity. The structure of the prepared blend flat sheet membranes was studied using scanning electron microscopy. Membrane separation performance was investigated in the process of ultrafiltration of human serum albumin buffered solutions. It was found that with the introduction of polysulfone to the polyphenylsulfone casting solution in N-methyl-2-pyrrolidone the size of supramolecular particles significantly increases with the maximum at (40–60):(60:40) polyphenylsulfone:polysulfone blend ratio from 76 nm to 196–354 nm. It was shown that polyphenylsulfone/polysulfone blend solutions, unlike the solutions of pristine polymers, are two-phase systems (emulsions) with the maximum droplet size and highest degree of polydispersity at polyphenylsulfone/polysulfone blend ratios (30–60):(70–40). Pure water flux of the blend membranes passes through a maximum in the region of the most heterogeneous structure of the casting solution, which is associated with the imposition of a polymer-polymer phase separation on the non-solvent induced phase separation upon membrane preparation. The application of polyphenylsulfone/polysulfone blends as membrane-forming polymers and polyethylene glycol (Mn = 400 g·mol−1) as a pore-forming agent to the casting solutions yields the formation of ultrafiltration membranes with high membrane pure water flux (270 L·m−2·h−1 at 0.1MPa) and human serum albumin rejection of 85%.

scholarly journals One-Step Preparation of Antifouling Polysulfone Ultrafiltration Membranes via Modification by a Cationic Polyelectrolyte Based on Polyacrylamide

Polymers ◽  
2020 ◽  
Vol 12 (5) ◽  
pp. 1017 ◽  
Author(s):  
Tatiana V. Plisko ◽  
Alexandr V. Bildyukevich ◽  
Katsiaryna S. Burts ◽  
Sergey S. Ermakov ◽  
Anastasia V. Penkova ◽  
...  
Keyword(s):  
Phase Separation ◽  
Human Serum Albumin ◽  
Zeta Potential ◽  
Serum Albumin ◽  
Human Serum ◽  
Cationic Polyelectrolyte ◽  
Coagulation Bath ◽  
Ultrafiltration Membranes ◽  
Selective Layer ◽  
One Step

A novel method for one-step preparation of antifouling ultrafiltration membranes via a non-solvent induced phase separation (NIPS) technique is proposed. It involves using aqueous 0.05–0.3 wt.% solutions of cationic polyelectrolyte based on a copolymer of acrylamide and 2-acryloxyethyltrimethylammonium chloride (Praestol 859) as a coagulant in NIPS. A systematic study of the effect of the cationic polyelectrolyte addition to the coagulant on the structure, performance and antifouling stability of polysulfone membranes was carried out. The methods for membrane characterization involved scanning electron microscopy (SEM), atomic force microscopy (AFM), Fourier transform infrared spectroscopy (FTIR), contact angle and zeta-potential measurements and evaluation of the permeability, rejection and antifouling performance in human serum albumin solution and surface water ultrafiltration. It was revealed that in the presence of cationic polyelectrolyte in the coagulation bath, its concentration has a major influence on the rate of “solvent–non-solvent” exchange and thus also on the rate of phase separation which significantly affects membrane structure. The immobilization of cationic polyelectrolyte macromolecules into the selective layer was confirmed by FTIR spectroscopy. It was revealed that polyelectrolyte macromolecules predominately immobilize on the surface of the selective layer and not on the bottom layer. Membrane modification was found to improve the hydrophilicity of the selective layer, to increase surface roughness and to change zeta-potential which yields the substantial improvement of membrane antifouling stability toward natural organic matter and human serum albumin.

Influence of Hydrophilic Polymer on Pure Water Permeation, Permeability Coefficient, and Porosity of Polysulfone Blend Membranes

2014 ◽  
Vol 931-932 ◽  
pp. 168-172 ◽  
Author(s):  
Asmadi Ali ◽  
Mohamad Awang ◽  
Ramli Mat ◽  
Anwar Johari ◽  
Mohd Johari Kamaruddin ◽  
...  
Keyword(s):  
Permeability Coefficient ◽  
Pure Water ◽  
Polymer Concentration ◽  
Water Flux ◽  
Hydrophilic Polymer ◽  
Hydrophobic Property ◽  
Water Permeation ◽  
Blend Membranes ◽  
Wet Phase Inversion ◽  
Pure Water Flux

It is well known that membrane with hydrophobic property is a fouling membrane. Polysulfone (PSf) membrane has hydrophobic characteristic was blended with a hydrophilic polymer, cellulose acetate phthalate (CAP) in order to increase hydrophilicity property of pure PSf membrane. In this study, membrane casting solutions containing 17 wt% of polymer was prepared via wet phase inversion process. The pure PSf membrane was coded as PC-0. PSf/CAP blend membranes with blend composition of 95/5, 90/10, 85/15 and 80/20 wt% of total polymer concentration in the membrane casting solutions were marked as PC-5, PC-10, PC-15 and PC-20 respectively. All of the membranes were characterized in terms of pure water flux and permeability coefficient in order to study their hydrophilicity properties. The investigated results shows that increased of CAP composition in PSf blend membranes has increased pure water flux, permeability coefficient and porosity of the blend membrane which in turn formed membrane with anti-fouling property.

scholarly journals Fabrication and Assessment of ZnO Modified Polyethersulfone Membranes for Fouling Reduction of Bovine Serum Albumin

2017 ◽  
Vol 2017 ◽  
pp. 1-8 ◽  
Author(s):  
Tshepo Duncan Dipheko ◽  
Kgabo Philemon Matabola ◽  
Kate Kotlhao ◽  
Richard M. Moutloali ◽  
Michael Klink
Keyword(s):  
Bovine Serum Albumin ◽  
Serum Albumin ◽  
Zno Nanoparticles ◽  
Bovine Serum ◽  
Pure Water ◽  
Water Flux ◽  
Composite Membranes ◽  
Optimal Performance ◽  
Fouling Resistance ◽  
Pure Water Flux

ZnO/PES composite membranes were fabricated by phase inversion method using DMAc as a solvent. The structure of ZnO was investigated using TEM, SEM, XRD, and TGA. TEM images of ZnO nanoparticles were well-defined, small, and spherically shaped with agglomerated nanoparticles particles of 50 nm. The SEM and XRD results were an indication that ZnO nanoparticles were present in the prepared ZnO/PES composites membranes. Contact angle measurements were used to investigate surface structures of the composite membranes. The amount of ZnO nanoparticles on PES membranes was varied to obtain the optimal performance of the composite membranes in terms of pure water flux, flux recovery, and fouling resistance using the protein bovine serum albumin (BSA) as a model organic foulant. The results showed that addition of ZnO to PES membranes improved the hydrophilicity, permeation, and fouling resistance properties of the membranes. Pure water flux increased from a low of 250 L/m2h for the neat membrane to a high of 410 L/m2h for the composite membranes. A high flux recovery of 80–94% was obtained for the composite membranes. The optimal performance of the composite membranes was obtained at 1.5 wt% of ZnO.

Preparation and Performance of Polysulfone Hollow Fiber Ultrafiltration Membranes

2013 ◽  
Vol 457-458 ◽  
pp. 309-312 ◽  
Author(s):  
Yang Bai ◽  
Zhen Liu ◽  
Dao Bao Sun
Keyword(s):  
Hollow Fiber ◽  
High Performance ◽  
Pure Water ◽  
Water Flux ◽  
Bath Temperature ◽  
Coagulation Bath ◽  
Membrane Structures ◽  
Ultrafiltration Membranes ◽  
Pure Water Flux ◽  
And Performance

Polysulfone (PSF) hollow fiber ultrafiltration membranes were successfully prepared by dry-wet spinning technology. Dimethylacetamide (DMAC) was used as a solvent, water was used as bore liquid and coagulation bath, polyvinylpyrrolidone (PVP) was used as polymeric additive. The effects of spinning conditions on membrane structures and properties were investigated in present study. The results indicated that with the increase of PVP concentration, pure water flux increased and developed finger-like pores were formed. High coagulation bath temperature restricted pure water flux, 30°C was the best for the preparation of high-performance ultrafiltration membranes. When the air length was 11cm, the membrane comprehensive performance was the best.

Morphology and Properties of a Series of PVDF Blend Membranes

2013 ◽  
Vol 750-752 ◽  
pp. 1941-1944
Author(s):  
Jiao Jiao Dong ◽  
Yu Feng Zhang ◽  
Dong Qing Liu
Keyword(s):  
Mechanical Properties ◽  
Pure Water ◽  
Water Flux ◽  
Transformation Method ◽  
Mass Ratio ◽  
Pvdf Membrane ◽  
Blend Membranes ◽  
Pure Water Flux ◽  
And Performance ◽  
Pure Pvdf

In this article, a series of the PVDF/PPTA blend membranes with porous structure and excellent performance were successfully prepared by the phase transformation method. The effect of the mass ratio of W(PVDF)/W(PPTA) was systematically investigated.The morphology of the blend membranes were examined using scanning electron microscope (SEM). The permeation performance was characterized by measuring pure water flux. Meanwhile, the mechanical properties of membranes were researched. The experiment results confirmed that the blending ratio is a major factor to influence the structure and performance of PVDF/PPTA blend membrane. The blend membranes possess much better permeability than pure PVDF membrane and fairly good the mechanical properties especially for the membrane made by PVDF : PPTA=6 : 1.

Effect of Shear Rate on Characteristics, Performance and Morphology of Polysulfone Blend Membranes

2014 ◽  
Vol 699 ◽  
pp. 305-310
Author(s):  
Asmadi Ali ◽  
Rosli Mohd Yunus ◽  
Mohamad Awang ◽  
Anwar Johari ◽  
Ramli Mat
Keyword(s):  
Shear Rate ◽  
Water Content ◽  
Pure Water ◽  
Water Flux ◽  
Casting Machine ◽  
Shear Rates ◽  
Membrane Fabrication ◽  
Blend Membranes ◽  
Pure Water Flux ◽  
And Performance

Rheological factor such as shear rate during membrane fabrication process has an effect on properties, structures and performance of membranes. Flat sheet asymmetric PSf/CAP blend membranes were prepared using an automatic casting machine at different shear rates in the range of 42.0 to 201.0 s-1. Results showed that increasing the shear rate from 42.0 to105 s-1 has increased the molecular orientation and thickness which then reduces the water content, porosity and pure water flux of PSf/CAP blend membranes. However, further increasing the shear rate beyond 105 s-1has resulted in an increase in the water content of PSf/CAP blend membranes.

Preparation and Characterizations of Polysulfone Flat Ultrafiltration Membranes

2011 ◽  
Vol 418-420 ◽  
pp. 169-172
Author(s):  
Shan Zhang ◽  
Zhen Liu
Keyword(s):  
Pure Water ◽  
Water Flux ◽  
Bath Temperature ◽  
Coagulation Bath ◽  
Egg Rejection ◽  
Evaporation Time ◽  
Ultrafiltration Membranes ◽  
Pure Water Flux ◽  
Coagulation Bath Temperature

The Polysulfone Flat ultrafiltration membranes were prepared with dimethylacetamide (DMAc) as solvent and polyvinypyrrolidone (PVP) as pore forming additive. Performance of PSF membrane such as pure water flux, albumin egg rejection were investigated. In addition, the same investigations were conducted with different coagulation bath temperature and evaporation time. The results show that there were a maximum of pure water flux and a minimum of the retention of Albumin when PVP content reach 14%.

Poly(lactic acid)/Biodegradable Polymer Blend for The Preparation of Flat-Sheet Membrane

2014 ◽  
Vol 69 (9) ◽  
Author(s):  
Kanungnuch Keawsupsak ◽  
Arisa Jaiyu ◽  
Julaluk Pannoi ◽  
Punthinee Somwongsa ◽  
Nopparat Wanthausk ◽  
...  
Keyword(s):  
Lactic Acid ◽  
Biodegradable Polymers ◽  
Polymer Blend ◽  
Pure Water ◽  
Water Flux ◽  
Testing Machine ◽  
Poly Lactic Acid ◽  
Blend Membranes ◽  
Pure Water Flux ◽  
Bsa Rejection

Biodegradable polymers have been more attractive for membrane materials, especially poly(lactic acid) (PLA) because they degrade in natural environment after use. In this study, the membranes were developed from a polymer blend of PLA and other biodegradable polymers, such as poly(butylene succinate) (PBS), poly(butylene adipate-co-terphthalate) (PBAT) and Poly(3-hydroxybutyrate-co-3-hydroxyvalerate) (PHBV). The membranes were formed via nonsolvent induced phase separation process using n-methyl-2-pyrrolidone (NMP) as a solvent and water as a nonsolvent. The pure water flux and BSA rejection were tested to determine the filtration performance of membranes. The microstructures and tensile strength of membranes were characterized by field emission scanning electron microscope (FE-SEM) and universal testing machine (UTM), respectively. All of membranes appeared finger-like and sponge-like structures in cross-section, and porous structure on surface. PLA/PHBV blend membranes had pure water flux and BSA rejection as high as PLA/PBS and PLA/PBAT blend membranes. The pure water flux and BSA rejection of the blend ratio (PLA/PHBV/NMP) of 15:1:84 were 65 l/m2•h and 79%, respectively.

scholarly journals Design and Construction of Ag@MOFs Immobilized PVDF Ultrafiltration Membranes with Anti-bacterial and Antifouling Properties

2020 ◽  
Vol 2020 ◽  
pp. 1-11 ◽  
Author(s):  
Wentao Xu ◽  
Huaqiang Zhuang ◽  
Zehai Xu ◽  
Mianli Huang ◽  
Shangchan Gao ◽  
...  
Keyword(s):  
Composite Material ◽  
Pure Water ◽  
Water Flux ◽  
Antibacterial Properties ◽  
Analytical Techniques ◽  
High Water ◽  
Fouling Resistance ◽  
Ultrafiltration Membranes ◽  
Water Contact ◽  
Pure Water Flux

In this work, Ag nanoparticle loading Mg(C10H16O4)2(H2O)2(Ag@MOF) composite material was successfully prepared by a facile strategy, and subsequently Ag-MOFs were used to modify the PVDF ultrafiltration membranes to obtain fouling resistance and higher water flux. The as-prepared PVDF membranes were systematically characterized by a series of analytical techniques such as Water Contact Angle (CA), Scanning Electron Microscopy (SEM), and SEM-mapping. Furthermore, the performance of membranes on antibacterial properties, the pure water flux, and fouling resistance was investigated in detail. Those results showed that the membrane modified by Ag@MOFs containing 30% Ag had the higher anti-bacterial performance, and the clear zone could be increased to 10 mm in comparison with that of blank membrane. Meanwhile, the pure water flux of Ag@MOF membranes increased from 85 L/m2 h to 157 L/m2 h, and the maximum membrane flux recovery rate (FRR) of 95.7% was obtained using SA as pollutant, which is attributed to the introduction of Ag@MOF composite material. Based on the above experimental results, it can be found that the Ag-MOF membranes displayed the excellent antibacterial activity, high water flux, and fine fouling resistance. This work provides a facile strategy to fabricate the Ag@MOFs modified membranes, and it shows an excellent anti-bacterial and water flux performance.

Sign in / Sign up

Export Citation Format

Share Document