scholarly journals Investigation of the Thermomechanical Response of Cyclically Loaded NiTi Alloys by Means of Temperature Frequency Domain Analyses

Materials ◽  
2021 ◽  
Vol 14 (24) ◽  
pp. 7866
Author(s):  
Sofia Di Leonardo ◽  
Riccardo Cappello ◽  
Gaetano Burriesci ◽  
Giuseppe Pitarresi
Keyword(s):  
Phase Transformation ◽  
Cyclic Loading ◽  
Frequency Domain ◽  
Second Order ◽  
Image Correlation ◽  
Thin Strip ◽  
Heat Sources ◽  
Thermoelastic Effect ◽  
Full Field ◽  
Thermomechanical Behaviour

Nickel–Titanium (NiTi) shape memory alloys subjected to cyclic loading exhibit reversible temperature changes whose modulation is correlated with the applied load. This reveals the presence of reversible thermomechanical heat sources activated by the applied stresses. One such source is the elastocaloric effect, accounting for the latent heat of Austenite–Martensite phase transformation. It is, however, observed that when the amplitude of cyclic loads is not sufficient to activate or further propagate this phase transformation, the material still exhibits a strong cyclic temperature modulation. The present work investigates the thermomechanical behaviour of NiTi under such low-amplitude cyclic loading. This is carried out by analysing the frequency domain content of temperature sampled over a time window. The amplitude and phase of the most significant harmonics are obtained and compared with the theoretical predictions from the first and second-order theories of the Thermoelastic Effect, this being the typical reversible thermomechanical coupling prevailing under elastic straining. A thin strip of NiTi, exhibiting a fully superelastic behaviour at room temperature, was investigated under low-stress amplitude tensile fatigue cycling. Full-field strain and temperature distributions were obtained by means of Digital Image Correlation and IR Thermography. The work shows that the full field maps of amplitude and phase of the first three significant temperature harmonics carry out many qualitative information about the stress and structural state of the material. It is, though, found that the second-order theory of the Thermoelastic Effect is not fully capable of justifying some of the features of the harmonic response, and further work on the specific nature of thermomechanical heat sources is required for a more quantitative interpretation.

scholarly journals Experimental Characterization of NiTi SMAs Thermomechanical Behaviour Using Temperature and Strain Full-Field Measurements

2008 ◽  
Vol 59 ◽  
pp. 140-149 ◽  
Author(s):  
Pauline Schlosser ◽  
Denis Favier ◽  
Herve Louche ◽  
Laurent Orgéas
Keyword(s):  
Field Measurements ◽  
Local Heat ◽  
Deformation Mechanisms ◽  
Temperature Fields ◽  
Thin Wall ◽  
Heat Sources ◽  
Stress Plateau ◽  
Full Field ◽  
Thermomechanical Behaviour

The tension behaviour of initially austenitic NiTi thin wall tubes was investigated using measurements of temperature and strain fields simultaneously. The first specimen was totally superelastic but the unloading was performed before the end of the loading stress plateau. The second specimen loading was performed beyond the stress plateau to allow analyzing the unloading, but was not superelastic and at a faster strain rate. Both tests show homogeneous behaviour at the beginning of the loading. Strong localisations, taking the shape of helical bands, are observed during the loading and unloading stress plateaus. To obtain quantitative energy information, allowing a better recognition of the deformation mechanisms, an estimation of the local heat sources based on image processing of the temperature fields is presented. Two methods of heat sources estimation allowing analysis of deformation mechanisms are proposed in the present paper: first during the homogeneous, then during localized stages.

scholarly journals Stereo-DIC Measurements of a Vibrating Bladed Disk: In-Depth Analysis of Full-Field Deformed Shapes

2021 ◽  
Vol 11 (12) ◽  
pp. 5430
Author(s):  
Paolo Neri ◽  
Alessandro Paoli ◽  
Ciro Santus
Keyword(s):  
Single Point ◽  
Excitation Frequency ◽  
Phase Variation ◽  
Operating Conditions ◽  
Image Correlation ◽  
Response Analysis ◽  
Full Field ◽  
Low Speed ◽  
Bladed Disk ◽  
Depth Analysis

Vibration measurements of turbomachinery components are of utmost importance to characterize the dynamic behavior of rotating machines, thus preventing undesired operating conditions. Local techniques such as strain gauges or laser Doppler vibrometers are usually adopted to collect vibration data. However, these approaches provide single-point and generally 1D measurements. The present work proposes an optical technique, which uses two low-speed cameras, a multimedia projector, and three-dimensional digital image correlation (3D-DIC) to provide full-field measurements of a bladed disk undergoing harmonic response analysis (i.e., pure sinusoidal excitation) in the kHz range. The proposed approach exploits a downsampling strategy to overcome the limitations introduced by low-speed cameras. The developed experimental setup was used to measure the response of a bladed disk subjected to an excitation frequency above 6 kHz, providing a deep insight in the deformed shapes, in terms of amplitude and phase distributions, which could not be feasible with single-point sensors. Results demonstrated the system’s effectiveness in measuring amplitudes of few microns, also evidencing blade mistuning effects. A deeper insight into the deformed shape analysis was provided by considering the phase maps on the entire blisk geometry, and phase variation lines were observed on the blades for high excitation frequency.

scholarly journals Full-Field Operational Modal Analysis of an Aircraft Composite Panel from the Dynamic Response in Multi-Impact Test

Sensors ◽  
2021 ◽  
Vol 21 (5) ◽  
pp. 1602
Author(s):  
Ángel Molina-Viedma ◽  
Elías López-Alba ◽  
Luis Felipe-Sesé ◽  
Francisco Díaz
Keyword(s):  
Modal Analysis ◽  
Energy Absorption ◽  
High Speed ◽  
Operational Modal Analysis ◽  
Modal Identification ◽  
Image Correlation ◽  
Composite Panel ◽  
Impact Excitation ◽  
Full Field ◽  
The Impact

Experimental characterization and validation of skin components in aircraft entails multiple evaluations (structural, aerodynamic, acoustic, etc.) and expensive campaigns. They require different rigs and equipment to perform the necessary tests. Two of the main dynamic characterizations include the energy absorption under impact forcing and the identification of modal parameters through the vibration response under any broadband excitation, which also includes impacts. This work exploits the response of a stiffened aircraft composite panel submitted to a multi-impact excitation, which is intended for impact and energy absorption analysis. Based on the high stiffness of composite materials, the study worked under the assumption that the global response to the multi-impact excitation is linear with small strains, neglecting the nonlinear behavior produced by local damage generation. Then, modal identification could be performed. The vibration after the impact was measured by high-speed 3D digital image correlation and employed for full-field operational modal analysis. Multiple modes were characterized in a wide spectrum, exploiting the advantages of the full-field noninvasive techniques. These results described a consistent modal behavior of the panel along with good indicators of mode separation given by the auto modal assurance criterion (Auto-MAC). Hence, it illustrates the possibility of performing these dynamic characterizations in a single test, offering additional information while reducing time and investment during the validation of these structures.

scholarly journals Experimental Characterization of the FRCM-Concrete Interface Bond Behavior Assisted by Digital Image Correlation

Sensors ◽  
2021 ◽  
Vol 21 (4) ◽  
pp. 1154
Author(s):  
Dario De Domenico ◽  
Antonino Quattrocchi ◽  
Damiano Alizzio ◽  
Roberto Montanini ◽  
Santi Urso ◽  
...  
Keyword(s):  
Digital Image Correlation ◽  
Digital Image ◽  
Mechanical Tests ◽  
Image Correlation ◽  
Front Face ◽  
Full Field ◽  
Bond Behavior ◽  
Externally Bonded ◽  
Strengthening Technique ◽  
Concrete Interface

Digital Image Correlation (DIC) provides measurements without disturbing the specimen, which is a major advantage over contact methods. Additionally, DIC techniques provide full-field maps of response quantities like strains and displacements, unlike traditional methods that are limited to a local investigation. In this work, an experimental application of DIC is presented to investigate a problem of relevant interest in the civil engineering field, namely the interface behavior between externally bonded fabric reinforced cementitious mortar (FRCM) sheets and concrete substrate. This represents a widespread strengthening technique of existing reinforced concrete structures, but its effectiveness is strongly related to the bond behavior between composite fabric and underlying concrete. To investigate this phenomenon, a set of notched concrete beams are realized, reinforced with FRCM sheets on the bottom face, subsequently cured in different environmental conditions (humidity and temperature) and finally tested up to failure under three-point bending. Mechanical tests are carried out vis-à-vis DIC measurements using two distinct cameras simultaneously, one focused on the concrete front face and another focused on the FRCM-concrete interface. This experimental setup makes it possible to interpret the mechanical behavior and failure mode of the specimens not only from a traditional macroscopic viewpoint but also under a local perspective concerning the evolution of the strain distribution at the FRCM-concrete interface obtained by DIC in the pre- and postcracking phase.

scholarly journals Reveal of Internal, Early-Load Interfacial Debonding on Cement Textile-Reinforced Sandwich Insulated Panels

2021 ◽  
Vol 11 (2) ◽  
pp. 879
Author(s):  
Eleni Tsangouri ◽  
Hasan Ismail ◽  
Matthias De Munck ◽  
Dimitrios G. Aggelis ◽  
Tine Tysmans
Keyword(s):  
Average Frequency ◽  
Technical Committee ◽  
Interfacial Debonding ◽  
Image Correlation ◽  
Rilem Technical Committee ◽  
Structural Element ◽  
Full Field ◽  
Displacement Mapping ◽  
Early Loading ◽  
Damage Tracking

Internal interfacial debonding (IID) phenomena on sandwich façade insulated panels are detected and tracked by acoustic emission (AE). The panels are made of a thin and lightweight cementitious composite skin. In the lab, the panels are tested under incremental bending simulating service loads (i.e., wind). Local (up to 150 mm wide) skin-core detachments are reported in the early loading stage (at 5% of ultimate load) and are extensively investigated in this study, since IID can detrimentally affect the long-term durability of the structural element. A sudden rise in the AE hits rate and a shift in the wave features (i.e., absolute energy, amplitude, rise time) trends indicate the debonding onset. AE source localization, validated by digital image correlation (DIC) principal strains and out-of-plane full-field displacement mapping, proves that early debonding occurs instantly and leads to the onset of cracks in the cementitious skin. At higher load levels, cracking is accompanied by local debonding phenomena, as proven by RA value increases and average frequency drops, a result that extends the state-of-the-art in the fracture assessment of concrete structures (Rilem Technical Committee 212-ACD). Point (LVDT) and full-field (AE/DIC) measurements highlight the need for a continuous and full-field monitoring methodology in order to pinpoint the debonded zones, with the DIC technique accurately reporting surface phenomena while AE offers in-volume damage tracking.

scholarly journals Full-field time-encoded frequency-domain optical coherence tomography

2006 ◽  
Vol 14 (17) ◽  
pp. 7661 ◽  
Author(s):  
Boris Považay ◽  
Angelika Unterhuber ◽  
Boris Hermann ◽  
Harald Sattmann ◽  
Holger Arthaber ◽  
...  
Keyword(s):  
Optical Coherence Tomography ◽  
Frequency Domain ◽  
Optical Coherence ◽  
Full Field

scholarly journals Material parameter identification using finite elements with time-adaptive higher-order time integration and experimental full-field strain information

2021 ◽  
Author(s):  
Stefan Hartmann ◽  
Rose Rogin Gilbert
Keyword(s):  
Experimental Data ◽  
Finite Elements ◽  
Parameter Identification ◽  
Material Parameter ◽  
Measurement Data ◽  
Least Square ◽  
Image Correlation ◽  
Field Strain ◽  
Material Parameter Identification ◽  
Full Field

AbstractIn this article, we follow a thorough matrix presentation of material parameter identification using a least-square approach, where the model is given by non-linear finite elements, and the experimental data is provided by both force data as well as full-field strain measurement data based on digital image correlation. First, the rigorous concept of semi-discretization for the direct problem is chosen, where—in the first step—the spatial discretization yields a large system of differential-algebraic equation (DAE-system). This is solved using a time-adaptive, high-order, singly diagonally-implicit Runge–Kutta method. Second, to study the fully analytical versus fully numerical determination of the sensitivities, required in a gradient-based optimization scheme, the force determination using the Lagrange-multiplier method and the strain computation must be provided explicitly. The consideration of the strains is necessary to circumvent the influence of rigid body motions occurring in the experimental data. This is done by applying an external strain determination tool which is based on the nodal displacements of the finite element program. Third, we apply the concept of local identifiability on the entire parameter identification procedure and show its influence on the choice of the parameters of the rate-type constitutive model. As a test example, a finite strain viscoelasticity model and biaxial tensile tests applied to a rubber-like material are chosen.

Sign in / Sign up

Export Citation Format

Share Document