scholarly journals Durability of Mortars with Fly Ash Subject to Freezing and Thawing Cycles and Sulfate Attack

Materials ◽  
2021 ◽  
Vol 15 (1) ◽  
pp. 220
Author(s):  
Monika Jaworska-Wędzińska ◽  
Iga Jasińska
Keyword(s):  
Fly Ash ◽  
Portland Cement ◽  
Sodium Sulfate ◽  
Sulfate Solution ◽  
Physical Factors ◽  
Sodium Sulfate Solution ◽  
Freezing And Thawing ◽  
High Calcium ◽  
High Calcium Fly Ash ◽  
Freezing And Thawing Cycles

Destruction of cement composites occurs due to the alternate or simultaneous effects of aggressive media, resulting in the destruction of concrete under the influence of chemical and physical factors. This article presents the results of changes in the measurement of linear strains of samples and changes in the microstructure of cement after 30 freezing and thawing cycles and immersed in 5% sodium sulfate solution. The compressive strengths ratios were carried out at the moment when the samples were moved to the sulfate solution after 30 cycles and at the end of the study when the samples showed visual signs of damage caused by the effect of 5% Na2SO4. The composition of the mixtures was selected based on the Gibbs triangle covering the area up to 40% replacement of Portland cement with low and high-calcium fly ashes or their mixture. Air-entrained and non-air entrained mortars were made of OPC, in which 20%, 26.6%, and 40% of Portland cement were replaced with low and/or high-calcium fly ash. Initial, freezing and thawing cycles accelerated the destruction of non- air-entrained cement mortars immersed in 5% sodium sulfate solution. The sulfate resistance, after the preceding frost damage, decreased along with the increase in the amount of replaced fly ash in the binder. Air-entrained mortars in which 20% of cement was replaced with high-calcium fly ash showed the best resistance to the action of sodium sulfate after 30 freezing and thawing cycles.

scholarly journals Deterioration Regularity of Sodium Sulfate Solution Attack on Cemented Coal Gangue-Fly Ash Backfill under Drying-Wetting Cycles

2020 ◽  
Vol 2020 ◽  
pp. 1-13
Author(s):  
Shaojie Chen ◽  
Zhen Zhang ◽  
Dawei Yin ◽  
Junbiao Ma
Keyword(s):  
Fly Ash ◽  
Sodium Sulfate ◽  
Sulfate Solution ◽  
Coal Gangue ◽  
Salt Crystallization ◽  
Sodium Sulfate Solution ◽  
Sulfate Ion ◽  
Sulfate Ions ◽  
Ion Contents ◽  
The Masses

To research the properties of cemented coal gangue-fly ash backfill (CGFB) exposed to different concentrations of sodium sulfate solutions under drying-wetting cycles, the mass changes, uniaxial compressive strengths, sulfate ion contents at different depths, and microstructures of CGFB samples were measured in this study. The results show that the CGFB samples were damaged by salt crystallization in the dry state and attacked by the expansive products in the wet state. The sulfate ion contents in CGFB samples increased with the sulfate concentrations and drying-wetting cycles and decreased from the surface to the inside of the samples. The damage process of CGFB samples evolved from the surface to the inside. In the early stage of corrosion, sulfate ions adsorbed to the surface of CGFB samples and consumed nonhydrated particles to form acicular ettringite and other products that filled the material pores. For this stage, the driving force of sulfate ions to enter into the CGFB samples was the highest for the samples immersed in 15% sodium sulfate solution, and the masses and strengths increased the fastest. As the drying-wetting cycles continued, the nonhydrated particles inside the samples were nearly completely hydrated, and the samples were constantly damaged by salt crystallization and dissolution. The corrosion ions entered into the samples and consumed portlandite to produce a large amount of prismatic ettringite and aggravated the internal corrosion of CGFB samples. At the fifteenth drying-wetting cycle, the higher the salt concentration of the immersion solution was, the faster the masses and the strengths of CGFB samples decreased. Moreover, the surface spalling and failure of CGFB samples were more severe.

Sulfate Resistance of Clay-Portland Cement and Clay High-Calcium Fly Ash Geopolymer

2015 ◽  
Vol 27 (5) ◽  
pp. 04014158 ◽  
Author(s):  
Patimapon Sukmak ◽  
Pre De Silva ◽  
Suksun Horpibulsuk ◽  
Prinya Chindaprasirt
Keyword(s):  
Fly Ash ◽  
Portland Cement ◽  
Sulfate Resistance ◽  
High Calcium ◽  
High Calcium Fly Ash

scholarly journals Experimental Study on the Durability of Fly Ash-Based Filling Paste in Environments with Different Concentrations of Sulfates

2018 ◽  
Vol 2018 ◽  
pp. 1-12 ◽  
Author(s):  
Boqiang Cui ◽  
Yin Liu ◽  
Hao Guo ◽  
Zhanxin Liu ◽  
Yao Lu
Keyword(s):  
Fly Ash ◽  
Sodium Sulfate ◽  
Sulfate Solution ◽  
Mechanical Analysis ◽  
Test Block ◽  
Sodium Sulfate Solution ◽  
Stress Strain ◽  
Hydrated Calcium Silicate ◽  
Soaking Time ◽  
Hydrated Products

In order to study the effects of different concentrations of sulfate on the strength of fly ash-based coal mine filling paste, using variable control, mechanical analysis, and other means, the changes in the uniaxial compressive strengths of filling paste blocks soaked in different concentrations of sodium sulfate solution for different durations are studied, and their stress-strain curves are discussed. The hydrated products of each block are analyzed at different stages by XRD, and the results indicate that different concentrations of sodium sulfate solution have different effects on the strength of the filling paste after soaking for different durations. A sodium sulfate solution with a concentration of 5% had an activator effect on the fly ash-based filling paste and enhanced the strength of the filling paste. A sodium sulfate solution with a concentration of 10% and 15% increased the early strength of the paste test block faster, but after 60 d, the strength decreased. The stress-strain curves for these blocks show that the elastic moduli of the filling paste test blocks change irregularly, and it was found that with the increase in soaking time, the blocks soaked in the 10% and 15% sodium sulfate solutions developed fissures in the later stage that adversely affected the strength of the filling paste. The XRD results show that the filling paste test block hydration products are hydrated calcium silicate (C-S-H) based and that ettringite (AFt), beneficial to strength of the filling paste in proper quantities, appeared in the main product of the filling paste test blocks that were soaked in the sodium sulfate solution. With the increase in the concentration of the sodium sulfate solution, the AFt is generated in larger quantities, and gypsum crystals begin to appear, which is not conducive to the filling paste block strength.

scholarly journals Durability Study on High Calcium Fly Ash Based Geopolymer Concrete

2015 ◽  
Vol 2015 ◽  
pp. 1-7 ◽  
Author(s):  
Ganesan Lavanya ◽  
Josephraj Jegan
Keyword(s):  
Fly Ash ◽  
Portland Cement ◽  
Sodium Hydroxide ◽  
Ordinary Portland Cement ◽  
Geopolymer Concrete ◽  
Portland Cement Concrete ◽  
Cement Concrete ◽  
High Calcium ◽  
High Calcium Fly Ash ◽  
Ordinary Portland Cement Concrete

This study presents an investigation into the durability of geopolymer concrete prepared using high calcium fly ash along with alkaline activators when exposed to 2% solution of sulfuric acid and 5% magnesium sulphate for up to 45 days. The durability was also assessed by measuring water absorption and sorptivity. Ordinary Portland cement concrete was also prepared as control concrete. The grades chosen for the investigation were M20, M40, and M60. The alkaline solution used for present study is the combination of sodium silicate and sodium hydroxide solution with the ratio of 2.50. The molarity of sodium hydroxide was fixed as 12. The test specimens were150×150×150 mm cubes,100×200 mm cylinders, and100×50 mm discs cured at ambient temperature. Surface deterioration, density, and strength over a period of 14, 28, and 45 days were observed. The results of geopolymer and ordinary Portland cement concrete were compared and discussed. After 45 days of exposure to the magnesium sulfate solution, the reduction in strength was up to 12% for geopolymer concrete and up to 25% for ordinary Portland cement concrete. After the same period of exposure to the sulphuric acid solution, the compressive strength decrease was up to 20% for geopolymer concrete and up to 28% for ordinary Portland cement concrete.

Influence of Nano-Silica Dosage on Properties of Cement Paste Incorporating with High Calcium Fly Ash

2020 ◽  
Vol 841 ◽  
pp. 9-13
Author(s):  
Teewara Suwan ◽  
Peerapong Jitsangiam ◽  
Prinya Chindaprasirt
Keyword(s):  
Fly Ash ◽  
Portland Cement ◽  
Cement Paste ◽  
Construction Material ◽  
Internal Heat ◽  
Nano Silica ◽  
Industrial Sectors ◽  
High Calcium ◽  
High Calcium Fly Ash ◽  
Cement And Concrete

Nanotechnology is receiving widespread attention in many industrial sectors, including construction material industry. One of the nano-scale admixtures, which has the potential to enhance the performance of cement and concrete, is known as Nano-silica (n-SiO2). In general, fly ash (FA) is currently used in cement and concrete industry for replacing the consumption of Portland cement (OPC) to reduce its production cost as well as to improve some specific required properties, e.g., workability or low internal heat liberation. However, the strength of hardened Portland cement is normally decreased when a higher amount of fly ash is presented. This research article is therefore pointed on the influence of nano-silica dosage on the properties of cement paste incorporating with high calcium fly ash. Seven different proportions of OPC:FA were prepared viz. 100:0, 80:20, 60:40, 50:50, 40:60, 20:80 and 0:100 by weight. The commercial grade nano-silica (in liquid form) was used as an admixture in those mixes by 0.0, 0.5, 1.0 and 1.5 wt% of the mixing water with a water-to-binder (w/b) ratio of 0.30. The results indicated that the addition of n-SiO2 improved the compressive strength of all mixtures (with and without high calcium FA) as the presence of n-SiO2 can be a source of silica and easily contribute to an additional formation of CSH in the cementing system, confirmed by the results of XRD analysis. The main findings show a potential approach of using n-SiO2 as an admixture for cement and concrete construction.

Effect of sodium hydroxide and sodium silicate solutions on strengths of alkali activated high calcium fly ash containing Portland cement

2016 ◽  
Vol 21 (6) ◽  
pp. 2202-2210 ◽  
Author(s):  
Tanakorn Phoo-ngernkham ◽  
Sakonwan Hanjitsuwan ◽  
Nattapong Damrongwiriyanupap ◽  
Prinya Chindaprasirt
Keyword(s):  
Fly Ash ◽  
Portland Cement ◽  
Sodium Hydroxide ◽  
Sodium Silicate ◽  
High Calcium ◽  
High Calcium Fly Ash ◽  
Alkali Activated

scholarly journals Damage and Degradation of Concrete under Coupling Action of Freeze-Thaw Cycle and Sulfate Attack

2020 ◽  
Vol 2020 ◽  
pp. 1-17 ◽  
Author(s):  
Wei Tian ◽  
Fangfang Gao
Keyword(s):  
Fly Ash ◽  
Sodium Sulfate ◽  
Sulfate Solution ◽  
Sulfate Attack ◽  
Sodium Sulfate Solution ◽  
Failure Characteristics ◽  
Freeze Thaw ◽  
Thaw Cycle ◽  
Freeze Thaw Cycle ◽  
Two Stages

In this study, the mechanical behaviors, failure characteristics, and microstructure of concrete containing fly ash (FA) against combined freeze-thaw cycles and sulfate attack were studied compared with normal concrete, and the formation rates of corrosion products during coupling cycles were investigated. Results showed that, during the coupling action of freeze-thaw cycles and sodium sulfate solution, concrete containing 10% fly ash exposed in 5% sodium sulfate solution exhibited better freeze-thaw resistance. Meanwhile, the variation of compressive strength of concrete during the coupling cycles could be divided into two stages, including the strength enhancement stage and the strength reduction stage. Moreover, the proportion of micropores and capillary pores decreased obviously during combined freeze-thaw cycles and sulfate attack, and excessive concentration of sodium sulfate solution led to more macropores after high-frequency freeze-thaw cycles.

Sign in / Sign up

Export Citation Format

Share Document