scholarly journals Synthesis and Characterization of a High Flux Nanocellulose–Cellulose Acetate Nanocomposite Membrane

Membranes ◽  
2019 ◽  
Vol 9 (6) ◽  
pp. 70 ◽  
Author(s):  
Nancy Li ◽  
Jackie Zheng ◽  
Pejman Hadi ◽  
Mengying Yang ◽  
Xiangyu Huang ◽  
...  
Keyword(s):  
Polymer Matrix ◽  
Energy Requirement ◽  
Cellulose Nanofibers ◽  
Membrane Resistance ◽  
High Energy ◽  
Sem Images ◽  
Membrane Performance ◽  
Aspect Ratios ◽  
Membrane Flux

Despite the advantages of membrane processes, their high energy requirement remains a major challenge. Fabrication of nanocomposite membranes by incorporating various nanomaterials in the polymer matrix has shown promise for enhancing membrane flux. In this study, we embed functionalized cellulose nanofibers (CNFs) with high aspect ratios in the polymer matrix to create hydrophilic nanochannels that reduce membrane resistance and facilitate the facile transport of water molecules through the membrane. The results showed that the incorporation of 0.1 wt % CNF into the polymer matrix did not change the membrane flux (~15 L · m − 2 · h − 1 ) and Bovine Serum Albumin (BSA) Fraction V rejection, while increasing the CNF content to 0.3 wt % significantly enhanced the flux by seven times to ~100 L · m − 2 · h − 1 , but the rejection was decreased to 60–70%. Such a change in membrane performance was due to the formation of hydrophilic nanochannels by the incorporation of CNF (corroborated by the SEM images), decreasing the membrane resistance, and thus enhancing the flux. When the concentration of the CNF in the membrane matrix was further increased to 0.6 wt %, no further increase in the membrane flux was observed, however, the BSA rejection was found to increase to 85%. Such an increase in the rejection was related to the electrostatic repulsion between the negatively-charged CNF-loaded nanochannels and the BSA, as demonstrated by zeta potential measurements. SEM images showed the bridging effect of the CNF in the nanochannels with high CNF contents.

scholarly journals A Comparative Study on the Characterization of Nanofibers with Cellulose I, I/II, and II Polymorphs from Wood

Polymers ◽  
2019 ◽  
Vol 11 (1) ◽  
pp. 153 ◽  
Author(s):  
Haiying Wang ◽  
Suiyi Li ◽  
Tiantian Wu ◽  
Xiaoxuan Wang ◽  
Xudong Cheng ◽  
...  
Keyword(s):  
Thermal Expansion ◽  
Comparative Study ◽  
Coefficient Of Thermal Expansion ◽  
Cellulose Nanofibers ◽  
High Yield ◽  
Chemical Extraction ◽  
Cellulose Content ◽  
Cellulose I ◽  
Aspect Ratios

Polymorphic changes in cellulose nanofibers (CNFs) are closely related to their properties and applications, and it is of interest to investigate how polymorphic changes influence their properties. A comparative study on the properties of CNFs with cellulose I, I/II, and II polymorphs from wood was conducted herein. CNFs were obtained by chemical extraction combined with a simple and efficient mechanical treatment (one pass through a grinder). This process resulted in a relatively high yield of 80–85% after a simple grinding treatment. The polymorphic changes in the CNFs and the chemical composition, morphology, tensile performances, and thermal properties were systematically characterized and compared. The X-ray diffraction and FTIR analyses verified the existence of three types of purified pulps and CNFs with cellulose I, cellulose I/II, and cellulose II polymorphs (CNF-I, CNF-I/II, CNF-II). Morphological observations presented that these three types of CNFs all exhibited high aspect ratios and entangled structures. Tensile testing showed that the CNF films all exhibited high tensile strengths, and the fracture strains of the CNF-I/II (11.8%) and CNF-II (13.0%) films were noticeably increased compared to those of the CNF-I film (6.0%). If CNF-II is used as reinforcing material, its larger fracture strain can improve the mechanical performance of the CNF composites, such as fracture toughness and impact strength. In addition, CNF-I, CNF-I/II, and CNF-II films showed very low thermal expansion in the range 20–150 °C, with the coefficient of thermal expansion values of 9.4, 17.1, and 17.3 ppm/K, respectively. Thermogravimetric analysis (TGA) revealed that the degradation temperature of CNF-I and CNF-II was greater than that of CNF-I/II, which was likely due to increased α-cellulose content. This comparative study of the characterization of CNF-I, CNF-I/II, and CNF-II provides a theoretical basis for the application of CNFs with different polymorphs and could broaden the applications of CNFs.

Preparation and Characterization of Antimicrobial PES Ultra-Filtration Membrane Modified with Capsaicin

2011 ◽  
Vol 356-360 ◽  
pp. 2338-2343 ◽  
Author(s):  
Han Min Wang ◽  
Xue Li Gao ◽  
Bao Wei Su ◽  
Cong Jie Gao
Keyword(s):  
Phase Inversion ◽  
Antibacterial Property ◽  
Inversion Method ◽  
Polyethylene Glycol 400 ◽  
Membrane Performance ◽  
Filtration Membrane ◽  
Membrane Flux ◽  
Ultra Filtration ◽  
Phase Inversion Method

The polyethersulfone ultra-filtration membrane was prepared by phase inversion method using polyethersulfone(PES), polyethylene glycol 400(PEG400) and N，N- dimethylamide(DMAC) as materials, and was modified by adding a capsaicin monomer named MBHBA which possess antibacterial property. The effects of MBHBA content on the ultra-filtration membrane performance were discussed. The results showed that the addition of MBHBA monomer effectively increased the membrane flux. And the modified membrane had strong inhibitory activity against Escherichia coli.

HIGH ENERGY SYNCHROTRON X-RAY MICROSPECTROSCOPY FOR GEOCHEMICAL CHARACTERIZATION OF TERRESTRIAL AND EXTRATERRESTRIAL SAMPLES

2016 ◽  
Author(s):  
Antonio Lanzirotti ◽  
◽  
Stephen R. Sutton ◽  
Matt Newville ◽  
Jeffrey P. Fitts ◽  
...  
Keyword(s):  
High Energy ◽  
Geochemical Characterization ◽  
X Ray

scholarly journals Green synthesis: Proposed mechanism and factors influencing the synthesis of platinum nanoparticles

2020 ◽  
Vol 9 (1) ◽  
pp. 386-398 ◽  
Author(s):  
Mahmood S. Jameel ◽  
Azlan Abdul Aziz ◽  
Mohammed Ali Dheyab
Keyword(s):  
Green Synthesis ◽  
Reaction Temperature ◽  
Platinum Nanoparticles ◽  
Energy Requirement ◽  
Average Particle Size ◽  
High Energy ◽  
Energy Utilization ◽  
Critical Parameters ◽  
Synthesis Process ◽  
Average Particle

AbstractPlatinum nanoparticles (Pt NPs) have attracted interest in catalysis and biomedical applications due to their unique structural, optical, and catalytic properties. However, the conventional synthesis of Pt NPs using the chemical and physical methods is constrained by the use of harmful and costly chemicals, intricate preparation requirement, and high energy utilization. Hence, this review emphasizes on the green synthesis of Pt NPs using plant extracts as an alternative approach due to its simplicity, convenience, inexpensiveness, easy scalability, low energy requirement, environmental friendliness, and minimum usage of hazardous materials and maximized efficiency of the synthesis process. The underlying complex processes that cover the green synthesis (biosynthesis) of Pt NPs were reviewed. This review affirms the effects of different critical parameters (pH, reaction temperature, reaction time, and biomass dosage) on the size and shape of the synthesized Pt NPs. For instance, the average particle size of Pt NPs was reported to decrease with increasing pH, reaction temperature, and concentration of plant extract.

scholarly journals Electrochemical Properties of Lipid Membranes Self-Assembled from Bicelles

Membranes ◽  
2020 ◽  
Vol 11 (1) ◽  
pp. 11
Author(s):  
Damian Dziubak ◽  
Kamil Strzelak ◽  
Slawomir Sek
Keyword(s):  
Electrochemical Properties ◽  
Self Assembly ◽  
Lipid Membranes ◽  
Lipid Membrane ◽  
Membrane Resistance ◽  
Electrochemical Characteristics ◽  
Freeze Thaw ◽  
Lipid Films ◽  
Supported Lipid Membranes

Supported lipid membranes are widely used platforms which serve as simplified models of cell membranes. Among numerous methods used for preparation of planar lipid films, self-assembly of bicelles appears to be promising strategy. Therefore, in this paper we have examined the mechanism of formation and the electrochemical properties of lipid films deposited onto thioglucose-modified gold electrodes from bicellar mixtures. It was found that adsorption of the bicelles occurs by replacement of interfacial water and it leads to formation of a double bilayer structure on the electrode surface. The resulting lipid assembly contains numerous defects and pinholes which affect the permeability of the membrane for ions and water. Significant improvement in morphology and electrochemical characteristics is achieved upon freeze–thaw treatment of the deposited membrane. The lipid assembly is rearranged to single bilayer configuration with locally occurring patches of the second bilayer, and the number of pinholes is substantially decreased. Electrochemical characterization of the lipid membrane after freeze–thaw treatment demonstrated that its permeability for ions and water is significantly reduced, which was manifested by the relatively high value of the membrane resistance.

scholarly journals Performance Analysis of Indentation Punch on High Energy Lithium Pouch Cells and Simulated Model Improvement

Polymers ◽  
2021 ◽  
Vol 13 (12) ◽  
pp. 1971
Author(s):  
Lihua Ye ◽  
Muhammad Muzamal Ashfaq ◽  
Aiping Shi ◽  
Syyed Adnan Raheel Shah ◽  
Yefan Shi
Keyword(s):  
Short Circuit ◽  
Lithium Ion ◽  
Mechanical Deformation ◽  
High Energy ◽  
State Of Charge ◽  
Punch Test ◽  
Short Course ◽  
Model Cell ◽  
The Impact

In this research, the aim relates to the material characterization of high-energy lithium-ion pouch cells. The development of appropriate model cell behavior is intended to simulate two scenarios: the first is mechanical deformation during a crash and the second is an internal short circuit in lithium-ion cells during the actual effect scenarios. The punch test has been used as a benchmark to analyze the effects of different state of charge conditions on high-energy lithium-ion battery cells. This article explores the impact of three separate factors on the outcomes of mechanical punch indentation experiments. The first parameter analyzed was the degree of prediction brought about by experiments on high-energy cells with two different states of charge (greater and lesser), with four different sizes of indentation punch, from the cell’s reaction during the indentation effects on electrolyte. Second, the results of the loading position, middle versus side, are measured at quasi-static speeds. The third parameter was the effect on an electrolyte with a different state of charge. The repeatability of the experiments on punch loading was the last test function analyzed. The test results of a greater than 10% state of charge and less than 10% state of charge were compared to further refine and validate this modeling method. The different loading scenarios analyzed in this study also showed great predictability in the load-displacement reaction and the onset short circuit. A theoretical model of the cell was modified for use in comprehensive mechanical deformation. The overall conclusion found that the loading initiating the cell’s electrical short circuit is not instantaneously instigated and it is subsequently used to process the development of a precise and practical computational model that will reduce the chances of the internal short course during the crash.

Sign in / Sign up

Export Citation Format

Share Document