scholarly journals A Tailored AlSiMg Alloy for Laser Powder Bed Fusion

Metals ◽  
2020 ◽  
Vol 10 (4) ◽  
pp. 514 ◽  
Author(s):  
Daniel Knoop ◽  
Andreas Lutz ◽  
Bernhard Mais ◽  
Axel von Hehl
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Heat Treatment ◽  
Aluminum Matrix ◽  
Powder Bed Fusion ◽  
Laser Powder Bed Fusion ◽  
Elongation At Break ◽  
Powder Bed ◽  
Wide Range ◽  
Strength And Ductility

The majority of aluminum alloys used for laser powder bed fusion are based on the aluminum–silicon system, particularly alloys containing 7 to 12 wt.% silicon and less than 1 wt.% magnesium. Silicon has a beneficial influence on melt viscosity during casting and laser additive manufacturing and prevents the formation of cracks. This study focused on the development of a new AlSi3.5Mg2.5 alloy for laser powder bed fusion with a Mg-Si content above 1.85 wt.% Mg2Si, which is the solubility limit of the α-aluminum matrix, and a subsequent heat treatment to adjust the mechanical properties with a wide range of strength and ductility values. The characterization of the microstructure was conducted by optical microscopy, scanning electron microscopy, transmission electron microscopy, and differential scanning calorimetry. The mechanical properties were determined by tensile tests and additional tight radius bending tests. The newly developed alloy was compared with AlSi10Mg and Scalmalloy®. AlSi3.5Mg2.5 offers higher strength and ductility than AlSi10Mg, at comparable material costs. The mechanical properties can be adjusted in a wide range of values using a single step heat treatment. After direct ageing, the samples exhibited a ultimate tensile strength (UTS) of 484 ± 1 MPa and an elongation at break of 10.5% ± 1.3%, while after soft annealing, they exhibited a UTS of 179 ± 2 MPa and an elongation at break of 25.6% ± 0.9%.

scholarly journals In Situ Formation of a Metastable β-Ti Alloy by Laser Powder Bed Fusion (L-PBF) of Vanadium and Iron Modified Ti-6Al-4V

Metals ◽  
2018 ◽  
Vol 8 (12) ◽  
pp. 1067 ◽  
Author(s):  
Florian Huber ◽  
Thomas Papke ◽  
Christian Scheitler ◽  
Lukas Hanrieder ◽  
Marion Merklein ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Homogeneous Element ◽  
Alloy Formation ◽  
Powder Bed Fusion ◽  
Laser Powder Bed Fusion ◽  
Powder Bed ◽  
Β Phase ◽  
Stabilizing Effect

The aim of this work is to investigate the β-Ti-phase-stabilizing effect of vanadium and iron added to Ti-6Al-4V powder by means of heterogeneous powder mixtures and in situ alloy-formation during laser powder bed fusion (L-PBF). The resulting microstructure was analyzed by metallographic methods, scanning electron microscopy (SEM), and electron backscatter diffraction (EBSD). The mechanical properties were characterized by compression tests, both prior to and after heat-treating. Energy dispersive X-ray spectroscopy showed a homogeneous element distribution, proving the feasibility of in situ alloying by LPBF. Due to the β-phase-stabilizing effect of V and Fe added to Ti-6Al-4V, instead of an α’-martensitic microstructure, an α/β-microstructure containing at least 63.8% β-phase develops. Depending on the post L-PBF heat-treatment, either an increased upsetting at failure (33.9%) compared to unmodified Ti-6Al-4V (28.8%), or an exceptional high compressive yield strength (1857 ± 35 MPa compared to 1100 MPa) were measured. The hardness of the in situ alloyed material ranges from 336 ± 7 HV0.5, in as-built condition, to 543 ± 13 HV0.5 after precipitation-hardening. Hence, the range of achievable mechanical properties in dependence of the post-L-PBF heat-treatment can be significantly expanded in comparison to unmodified Ti-6Al-4V, thus providing increased flexibility for additive manufacturing of titanium parts.

scholarly journals Control of Crystallographic Texture and Mechanical Properties of Hastelloy-X via Laser Powder Bed Fusion

Crystals ◽  
2021 ◽  
Vol 11 (9) ◽  
pp. 1064
Author(s):  
Shinya Hibino ◽  
Tsubasa Todo ◽  
Takuya Ishimoto ◽  
Ozkan Gokcekaya ◽  
Yuichiro Koizumi ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Process Parameters ◽  
Crystallographic Texture ◽  
Lamellar Microstructure ◽  
Powder Bed Fusion ◽  
Laser Powder Bed Fusion ◽  
Hastelloy X ◽  
Single Crystalline ◽  
Powder Bed ◽  
Wide Range

The influence of various laser powder bed fusion (LPBF) process parameters on the crystallographic textures and mechanical properties of a typical Ni-based solid-solution strengthened alloy, Hastelloy-X, was examined. Samples were classified into four groups based on the type of crystallographic texture: single crystalline-like microstructure with <100>//build direction (BD) (<100>-SCM), single crystalline-like microstructure with <110>//BD (<110>-SCM), crystallographic lamellar microstructure (CLM), or polycrystalline microstructure (PCM). These four crystallographic textures were realized in Hastelloy-X for the first time here to the best of our knowledge. The mechanical properties of the samples varied depending on their texture. The tensile properties were affected not only by the Schmid factor but also by the grain size and the presence of lamellar boundaries (grain boundaries). The lamellar boundaries at the interface between the <110>//BD oriented main layers and the <100>//BD-oriented sub-layers of CLM contributed to the resistance to slip transmission and the increased proof stress. It was possible to control a wide range of crystallographic microstructures via the LPBF process parameters, which determines the melt pool morphology and solidification behavior.

scholarly journals Structure and Properties of Ti/Ti64 Graded Material Manufactured by Laser Powder Bed Fusion

Materials ◽  
2021 ◽  
Vol 14 (20) ◽  
pp. 6140
Author(s):  
Evgenii Borisov ◽  
Igor Polozov ◽  
Kirill Starikov ◽  
Anatoly Popovich ◽  
Vadim Sufiiarov
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Additive Manufacturing ◽  
Hot Isostatic Pressing ◽  
Powder Bed Fusion ◽  
Laser Powder Bed Fusion ◽  
Powder Bed ◽  
Isostatic Pressing ◽  
Graded Material ◽  
Single Part

Multimaterial additive manufacturing is an attractive way of producing parts with improved functional properties by combining materials with different properties within a single part. Pure Ti provides a high ductility and an improved corrosion resistance, while the Ti64 alloy has a higher strength. The combination of these alloys within a single part using additive manufacturing can be used to produce advanced multimaterial components. This work explores the multimaterial Laser Powder Bed Fusion (L-PBF) of Ti/Ti64 graded material. The microstructure and mechanical properties of Ti/Ti64-graded samples fabricated by L-PBF with different geometries of the graded zones, as well as different effects of heat treatment and hot isostatic pressing on the microstructure of the bimetallic Ti/Ti64 samples, were investigated. The transition zone microstructure has a distinct character and does not undergo significant changes during heat treatment and hot isostatic pressing. The tensile tests of Ti/Ti64 samples showed that when the Ti64 zones were located along the sample, the ratio of cross-sections has a greater influence on the mechanical properties than their shape and location. The presented results of the investigation of the graded Ti/Ti64 samples allow tailoring properties for the possible applications of multimaterial parts.

scholarly journals Multi-Laser Powder Bed Fusion Benchmarking—Initial Trials with Inconel 625

2019 ◽  
Vol 105 (7-8) ◽  
pp. 2891-2906 ◽  
Author(s):  
H. Wong ◽  
K. Dawson ◽  
G. A. Ravi ◽  
L. Howlett ◽  
R. O. Jones ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Production Rate ◽  
Single Mode ◽  
Inconel 625 ◽  
Powder Bed Fusion ◽  
Laser Powder Bed Fusion ◽  
Powder Bed ◽  
Single Laser ◽  
Stress Relieving

Abstract Production rate is an increasingly important factor in the deployment of metal additive manufacturing (AM) throughout industry. To address the perceived low production rate of metal AM systems based on single-laser powder bed fusion (L-PBF), several companies now offer systems in which melting has been parallelised by the introduction of multiple, independently controlled laser beams. Nevertheless, a full set of studies is yet to be conducted to benchmark the efficiency of multi-laser systems and, at the same time, to verify if the mechanical properties of components are compromised due to the increase in build rate. This study addresses the described technology gaps and presents a 4-beam L-PBF system operating in “single multi” (SM) mode (SM-L-PBF) where each of the four lasers is controlled so that it melts all of a particular components’ layers and produces specimens for comparison with standard L-PBF specimens from the same machine. That is all four lasers making all of some of the parts were compared to a single-laser manufacturing all of the parts. Build parameters were kept constant throughout the manufacturing process and the material used was Inconel 625 (IN625). Stress-relieving heat treatment was conducted on As-built (AB) specimens. Both AB and heat-treated (HT) specimen sets were tested for density, microstructure, tensile strength and hardness. Results indicate that the stress-relieving heat treatment increases specimen ductility without compromising other mechanical properties. SM-L-PBF has achieved a build rate of 14 cm3/h when four 200 W lasers were used to process IN625 at a layer thickness of 30 μm. An increase in the build rate of 2.74 times (build time reduction: 63%) has been demonstrated when compared to that of L-PBF, with little to no compromises in specimen mechanical properties. The observed tensile properties exceed the American Society for Testing Materials (ASTM) requirements for IN625 (by a margin of 22 to 26% in the 0.2% offset yield strength). Average specimen hardness and grain size are in the same order as that reported in literatures. The study has demonstrated that a multi-laser AM system opens up opportunities to tackle the impasse of low build rate in L-PBF in an industrial setting and that at least when operating in single mode there is no detectable degradation in the mechanical and crystallographic characteristics of the components produced.

Sign in / Sign up

Export Citation Format

Share Document