scholarly journals Design and Multidimensional Screening of Flash-PEO Coatings for Mg in Comparison to Commercial Chromium(VI) Conversion Coating

Metals ◽  
2021 ◽  
Vol 11 (2) ◽  
pp. 337
Author(s):  
Ewa Wierzbicka ◽  
Marta Mohedano ◽  
Endzhe Matykina ◽  
Raul Arrabal
Keyword(s):  
Corrosion Resistance ◽  
Corrosion Protection ◽  
Electrochemical Impedance ◽  
Salt Spray ◽  
Conversion Coating ◽  
Neutral Salt ◽  
Chromium Vi ◽  
Alkaline Electrolytes ◽  
Az31b Alloy ◽  
Plasma Electrolytic

REACH (Registration, Evaluation, Authorisation and Restriction of Chemicals) regulations demand for an expedient discovery of a Cr(VI)-free alternative corrosion protection for light alloys even though the green alternatives might never be as cheap as current harmful technologies. In the present work, flash- plasma electrolytic oxidation coatings (FPEO) with the process duration < 90 s are developed on AZ31B alloy in varied mixtures of silicate-, phosphate-, aluminate-, and fluoride-based alkaline electrolytes implementing current density and voltage limits. The overall evaluation of the coatings’ anticorrosion performance (electrochemical impedance spectroscopy (EIS), neutral salt spray test (NSST), paintability) shows that from nine optimized FPEO recipes, two (based on phosphate, fluoride, and aluminate or silicate mixtures) are found to be an adequate substitute for commercially used Cr(VI)-based conversion coating (CCC). The FPEO coatings with the best corrosion resistance consume a very low amount of energy (~1 kW h m−2 µm−1). It is also found that the lower the energy consumption of the FPEO process, the better the corrosion resistance of the resultant coating. The superb corrosion protection and a solid environmentally friendly outlook of PEO-based corrosion protection technology may facilitate the economic justification for industrial end-users of the current-consuming process as a replacement of the electroless CCC process.

Passivation Effect of Rare Earth Lanthanum on Galvanized Steel

2014 ◽  
Vol 525 ◽  
pp. 31-34
Author(s):  
Xiao Feng Liu
Keyword(s):  
Corrosion Resistance ◽  
Rare Earth ◽  
Electrochemical Impedance ◽  
Orthogonal Experiment ◽  
Salt Spray ◽  
Conversion Coating ◽  
Galvanized Steel ◽  
Neutral Salt ◽  
White Rust ◽  
Order Of Magnitude

By way of chemical marinate method, carrying out rare earth lanthanum to corrosion protect galvanized steel. The process of rare earth lanthanum conversion coating for galvanized steel was studied by using orthogonal experiment to get the optimized passivation parameters when the concentration of La (NO3) is 30g/L, H2O2is 20ml/L, pH=4 and was passivated at 40°C for 30s. The corrosion resistance was examined by weight loss tests, neutral salt spray tests (NSS) and electrochemical impedance spectroscopy (EIS). The results showed that the corrosion impedance of the pretreated sample was significantly improved, the corrosion rate was decreased by one order of magnitude, and the anti-white rust time was 54h.

scholarly journals Application of Commercial Surface Pretreatments on the Formation of Cerium Conversion Coating (CeCC) over High-Strength Aluminum Alloys 2024-T3 and 7075-T6

Metals ◽  
2021 ◽  
Vol 11 (6) ◽  
pp. 930
Author(s):  
Juan Jesús Alba-Galvín ◽  
Leandro González-Rovira ◽  
Francisco Javier Botana ◽  
Maria Lekka ◽  
Francesco Andreatta ◽  
...  
Keyword(s):  
Electrochemical Impedance ◽  
Salt Spray ◽  
Aluminum Matrix ◽  
Optical Emission ◽  
High Strength ◽  
Chemical Conversion ◽  
Conversion Coating ◽  
Neutral Salt ◽  
Corrosion Properties ◽  
Surface Pretreatment

The selection of appropriate surface pretreatments is one of the pending issues for the industrial application of cerium-based chemical conversion coatings (CeCC) as an alternative for toxic chromate conversion coating (CrCC). A two-step surface pretreatment based on commercial products has been successfully used here to obtain CeCC on AA2024-T3 and AA7075-T6. Specimens processed for 1 to 15 min in solutions containing CeCl3 and H2O2 have been studied by scanning electron microscopy coupled with energy-dispersive X-ray analysis (SEM-EDX), glow discharge optical emission spectroscopy (GDOES), potentiodynamic linear polarization (LP), electrochemical impedance spectroscopy (EIS), and neutral salt spray (NSS) tests. SEM-EDX showed that CeCC was firstly observed as deposits, followed by a general coverage of the surface with the formation of cracks where the coating was getting thicker. GDOES confirmed an increase of the CeCC thickness as the deposition proceed, the formation of CeCC over 7075 being faster than over 2024. There was a Ce-rich layer in both alloys and an aluminum oxide/hydroxide layer on 7075 between the upper Ce-rich layer and the aluminum matrix. According to LP and EIS, CeCC in all samples offered cathodic protection and comparable degradation in chloride-containing media. Finally, the NSS test corroborated the anti-corrosion properties of the CeCC obtained after the commercial pretreatments employed.

Corrosion resistance of composite coating used for fastener protection

2019 ◽  
Vol 66 (5) ◽  
pp. 595-602
Author(s):  
Zhifeng Lin ◽  
Likun Xu ◽  
Xiangbo Li ◽  
Li Wang ◽  
Weimin Guo ◽  
...  
Keyword(s):  
Corrosion Resistance ◽  
Carbon Steel ◽  
Composite Coating ◽  
Marine Environment ◽  
Electrochemical Impedance ◽  
Salt Spray ◽  
Diffusion Method ◽  
Economic Losses ◽  
Neutral Salt ◽  
Content Type

Purpose The purpose of this paper is to examine the performance of a fastener composite coating system, sherardized (SD) coating/zinc-aluminum (ZA) coating whether it has good performance in marine environment. Design/methodology/approach In this paper, SD coating was fabricated on fastener surface by solid-diffusion method. ZA coating was fabricated by thermal sintering method. Corrosion behaviours of the composite coating were investigated with potentiodynamic polarization curves, open circuit potential and electrochemical impedance spectroscopy methods. Findings Neutral salt spray (NSS) and deep sea exposure tests revealed that the composite coating had excellent corrosion resistance. Polarization curve tests showed that corrosion current density of the sample with composite coating was significantly decreased, indicating an effective corrosion protection of the composite coating. OCP measurement of the sample in NaCl solution demonstrated that the composite coating had the best cathodic protection effect. The good corrosion resistance of the composite coating was obtained by the synergy of SD and ZA coating. Practical implications SD/ZA coating can be used in marine environment to prolong the life of carbon steel fastener. Social implications SD/ZA composite coating can reduce the risk and accident caused by failed fastener, avoid huge economic losses. Originality/value A new kind of composite coating was explored to protect the carbon steel fastener in marine environment. And the composite coating has the long-term anti-corrosion performance both in simulated and marine environment test.

scholarly journals Improvement of AZ91 Alloy Corrosion Properties by Duplex NI-P Coating Deposition

Materials ◽  
2020 ◽  
Vol 13 (6) ◽  
pp. 1357 ◽  
Author(s):  
Jaromír Wasserbauer ◽  
Martin Buchtík ◽  
Jakub Tkacz ◽  
Stanislava Fintová ◽  
Jozef Minda ◽  
...  
Keyword(s):  
Corrosion Resistance ◽  
Magnesium Alloy ◽  
Corrosion Behavior ◽  
Electrochemical Impedance ◽  
Salt Spray ◽  
Az91 Alloy ◽  
Neutral Salt ◽  
Az91 Magnesium Alloy ◽  
Corrosion Properties ◽  
Az91 Magnesium

The corrosion behavior of duplex Ni-P coatings deposited on AZ91 magnesium alloy was studied. The electroless deposition process of duplex Ni-P coating consisted in the preparation of low-phosphorus Ni-P coating (5.7 wt.% of P), which served as a bond coating and high-phosphorus Ni-P coating (11.5 wt.% of P) deposited on it. The duplex Ni-P coatings with the thickness of 25, 50, 75 and 100 µm were deposited on AZ91 magnesium alloy. The electrochemical corrosion behavior of coated AZ91 magnesium alloy was investigated by electrochemical impedance spectroscopy and potentiodynamic polarization method in 0.1 M NaCl. Obtained results showed a significant improvement in the corrosion resistance of coated specimens when compared to uncoated AZ91 magnesium alloy. From the results of the immersion tests in 3.5 wt.% NaCl, 10% solution of HCl and NaOH and 5% neutral salt spray, a noticeable increase in the corrosion resistance with the increasing thickness of the Ni-P coating was observed.

scholarly journals Comparative Study on the Corrosion Resistance of 6061Al and SiC3D/6061Al Composite in a Chloride Environment

Materials ◽  
2021 ◽  
Vol 14 (24) ◽  
pp. 7730
Author(s):  
Liang Yu ◽  
Shuangshuang Hao ◽  
Xiaodong Nong ◽  
Xiuling Cao ◽  
Chen Zhang ◽  
...  
Keyword(s):  
Corrosion Resistance ◽  
Electrochemical Impedance ◽  
Salt Spray ◽  
Specific Area ◽  
Open Circuit ◽  
Pressure Casting ◽  
Neutral Salt ◽  
Salt Leaching ◽  
Chloride Environment ◽  
Al Matrix

Interface problems and the destruction of the continuity of the oxide film in the Al matrix usually reduce the corrosion resistance of the material. In this paper, the corrosion resistance of Al matrix composites (AMCs) was improved by introducing the silicon carbide skeletons (SiC3D) obtained with polymer replica technology. SiC3D/6061Al was fabricated by infiltrating molten 6061Al alloy in the oxidized SiC3D using the low-pressure casting method. The corrosion resistance performances of 6061Al and SiC3D/6061Al in NaCl solution were studied by electrochemical, neutral salt spray corrosion (NSS), and salt leaching (SL) tests. Results show corrosion resistance of SiC3D/6061Al is higher than that of 6061Al alloys by open circuit potential (OCP), potentio-dynamic polarization (PDP), and electrochemical impedance spectroscopy (EIS) tests. However, NSS and SL tests show the corrosion resistance of SiC3D/6061Al is lower than that of 6061Al alloy. The reason is a corrosion resistant and anti-oxidation network macrostructure with large interface recombination, few concentrated interfaces, and a small specific area that formed in SiC3D/6061Al. SiC3D cannot damage the continuity of the Al2O3 passivating film, and the network macrostructure greatly improves the corrosion resistance performance.

Corrosion Protection of Aluminum Alloy 2024-T3 by Vanadate Conversion Coatings

CORROSION ◽  
2004 ◽  
Vol 60 (3) ◽  
pp. 284-296 ◽  
Author(s):  
H. Guan ◽  
R. G. Buchheit
Keyword(s):  
Aluminum Alloy ◽  
Corrosion Protection ◽  
Inductively Coupled Plasma ◽  
Electrochemical Impedance ◽  
Salt Spray ◽  
Conversion Coating ◽  
Self Healing ◽  
Pitting Potential ◽  
X Ray ◽  
Aluminum Alloy 2024

Abstract In this paper, the formation, chemistry, morphology, and corrosion protection of a new type of inorganic conversion coating is described. This coating, referred to as a vanadate conversion coating (VCC), forms on aluminum alloy substrates in a matter of minutes during simple immersion in aqueous vanadate-based solutions at ambient temperatures. VCCs are yellow in color and conformal across the surface of aluminum alloy 2024-T3 (AA2024-T3 [UNS A92024]) substrates. Auger electron sputter depth profiles and x-ray absorption near-edge spectroscopy show that VCCs formed by a 3-min immersion are 300 nm to 500 nm thick and consist of a mixture of vanadium oxides and other components in the coating bath. In anodic polarization experiments conducted in aerated chloride solutions, VCCs increase the pitting potential and decrease the rate of oxygen reduction. When characterized by electrochemical impedance spectroscopy, VCCs demonstrate a low-frequency impedance between 1 MΩ-cm2 and 2 MΩ-cm2 after 24 h exposure to aerated 0.5 M sodium chloride (NaCl) solutions. In salt spray testing conducted according to ASTM B117, VCCs suppress formation of large pits for more than 168 h. VCCs also appear to be self-healing. Analysis of solution in contact with VCCs by inductively coupled plasma emission spectroscopy indicates that vanadate is released into solution upon exposure. Vanadium deposits were identified by x-ray microchemical analysis on a bare alloy substrate held in close proximity to a vanadate conversion-coated surface, and corrosion resistance of this bare surface was observed to increase during exposure. An important component of VCC formation appears to involve inorganic polymerization of V5+, which leads to the buildup of a film that passivates the surface and inhibits corrosion.

scholarly journals Effect of Plasma Surface Pretreatment on Ce3+-Doped GPTMS-ZrO2 Self-Healing Coatings on Aluminum Alloy

2012 ◽  
Vol 2012 ◽  
pp. 1-9 ◽  
Author(s):  
N. Kumar ◽  
A. Jyothirmayi ◽  
R. Subasri
Keyword(s):  
Aluminum Alloy ◽  
Corrosion Protection ◽  
Electrochemical Impedance ◽  
Condensation Reaction ◽  
Salt Spray ◽  
Neutral Salt ◽  
Self Healing ◽  
Surface Pretreatment ◽  
Plasma Surface ◽  
Coating Deposition

A hybrid sol synthesized from an acid-catalyzed hydrolysis and condensation reaction of 3-glycidoxypropyltrimethoxysilane (GPTMS) and zirconium n-propoxide was used as a matrix nanocomposite sol. To this sol, 0.01 M Ce3+ was added as an inhibitor to provide a self-healing coating system. The effect of an atmospheric air plasma surface pretreatment of aluminum alloy substrates prior to coating deposition of Ce3+-doped/undoped GPTMS-ZrO2 sol was studied with respect to corrosion protection. Coatings were generated by a dip coating technique employing a withdrawal speed of 5 mm/s and thermally cured at 130° C for 1 h. The coated Al surfaces were characterized using potentiodynamic polarization studies and electrochemical impedance spectroscopy. They were also subjected to accelerated corrosion testing using neutral salt spray test with 5% NaCl solution after creating an artificial scratch for more than 200 hours to assess the self-healing ability of coatings. It was observed that cerium (III) doping was effective for corrosion protection during long-term exposure to the electrolyte solution, and a plasma surface pretreatment of substrates prior to coating deposition of Ce3+-doped coatings improved the adhesion of coatings that provides enhanced corrosion protection along with self-healing ability exhibited in case of damages/scratches caused in the coating.

scholarly journals Accelerated Corrosion Tests in Quality Labels for Powder Coatings on Galvanized Steel—Comparison of Requirements and Experimental Evaluation

Materials ◽  
2021 ◽  
Vol 14 (21) ◽  
pp. 6547
Author(s):  
Izabela Kunce ◽  
Agnieszka Królikowska ◽  
Leszek Komorowski
Keyword(s):  
Corrosion Resistance ◽  
Corrosion Protection ◽  
Experimental Evaluation ◽  
Salt Spray ◽  
Galvanized Steel ◽  
Neutral Salt ◽  
Powder Coatings ◽  
Accelerated Corrosion ◽  
Corrosion Tests ◽  
Accelerated Corrosion Tests

Powder coatings are widely applied for corrosion protection of steel, aluminum, and hot dip galvanized steel in a variety of corrosive environments. Powder coatings are subjected to a number of strict laboratory tests to determine their mechanical properties, corrosion resistance, and color stability. Among European quality certificates for powder coatings applied to galvanized steel, the most commonly recognized are GSB-ST and Qualisteelcoat certificates, which also refer to the EN 13438 standard. Certificates of quality for powder coatings are constantly updated according to the latest research results and experience of specialists operating in the field of corrosion protection. This paper presents an experimental evaluation of how the required length of selected accelerated corrosion tests can affect the final assessment of powder coatings. On the example of two powder painting systems: polyester as well as based on epoxy and polyester resins, the paper presents the influence of the time of accelerated corrosion tests: ISO 6270, ISO 9227 (Neutral Salt Spray and Acetic Acid Salt Spray), and ISO 3231 on the protective properties of the coatings. The results of damage assessment according to ISO 4628 have been correlated with the requirements of particular quality specifications. Additionally, based on FTIR (Fourier Transform Infrared Spectroscopy) and EIS (Electrochemical Impedance Spectroscopy) analyses, the influence of the applied corrosion tests on the degradation degree of the coatings studied has been presented. The paper aims to present a tests for those powder coating systems applied to facilities for which the main requirement is corrosion resistance rather than aesthetics.

Effect of halloysite nanotubes on corrosion protection properties of the self-curing epoxy resin coatings

2021 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Gongwen Tang ◽  
Tingting Ren ◽  
Yi Wang ◽  
Zhishan Yan ◽  
Linrong Ma ◽  
...  
Keyword(s):  
Corrosion Resistance ◽  
Epoxy Resin ◽  
Corrosion Protection ◽  
Salt Spray ◽  
Thermo Gravimetric Analysis ◽  
Halloysite Nanotubes ◽  
The Self ◽  
Gravimetric Analysis ◽  
Neutral Salt ◽  
Content Type

Purpose The purpose of this paper is to study the effect of the nano tube fillers on the corrosion protection properties of the self-curing epoxy (SEP) coatings. Design/methodology/approach The self-curing epoxy (SEP) resin was synthesized via a reaction between diisopropoxy-bis ethylacetoacetato titanate and the epoxy resin. Halloysite nanotubes (HNTs) was surface modified by grafting (3-glycidoxypropyl) trimethoxysilane to obtain modified HNTs (mHNTs). The HNTs and mHNTs are used as nano tube fillers for the SEP coating. The thermal stability of the coatings was assessed via thermo-gravimetric analysis. The field-emission scanning electron microscopy (SEM) was conducted to analyze the surfaces and cross sections of the coatings. The anticorrosive efficiencies of the coatings were investigated by electrochemical measurements and a neutral salt spray test. Findings The results demonstrated that the additions of HNTs and mHNTs have little effect on the thermal degradation temperature of the SEP coating. However, the addition of the nanotubes reduced the corrosion resistance of the SEP coating. Originality/value The SEP coating itself showed excellent corrosion resistance without any reinforcement particles and is hence promising for application in the heavy-duty anticorrosion field of heat exchangers.

The Corrosion Resistance of Zn-Plated Samples with Blackish Green Passivation Film

2011 ◽  
Vol 383-390 ◽  
pp. 3081-3085
Author(s):  
Yu Bao Cao
Keyword(s):  
Corrosion Resistance ◽  
Electrochemical Impedance ◽  
Salt Spray ◽  
Sample Surface ◽  
Corrosion Current ◽  
Electrochemical Process ◽  
Salt Spray Test ◽  
Neutral Salt ◽  
Passivation Film ◽  
Passivated Sample

The corrosion resistance of blackishgreen passivation films on zinc-plated steel sheet was studied by polarization curve measurement, electrochemical impedance spectroscopy and neutral salt spray test. The passivated sample featured a more positive corrosion potential and much lower corrosion current density as compared to non-passivated sample in 5% (mass fraction) NaCl solution. The Nyquist plots of the samples with and without passivation were characterized as two complete capacitive arcs, indicating that the corrosion is controlled by electrochemical process. The radii of capacitive arcs of the passivated sample are larger than those of non-passivated sample, because the passivation film formed on the sample surface increases the reaction resistance in corrosion process, thus the corrosion resistance of the sample is improved. The anti-white rust time of the passivation film in neutral salt spray test is 400 h.

Sign in / Sign up

Export Citation Format

Share Document