scholarly journals Tungsten Matrix Composite Reinforced with CoCrFeMnNi High-Entropy Alloy: Impact of Processing Routes on Microstructure and Mechanical Properties

Metals ◽  
2019 ◽  
Vol 9 (9) ◽  
pp. 992 ◽  
Author(s):  
P. V. Satyanarayana ◽  
R. Sokkalingam ◽  
P. K. Jena ◽  
K. Sivaprasad ◽  
K. G. Prashanth
Keyword(s):  
Heating Rate ◽  
Microwave Sintering ◽  
Oxide Phase ◽  
High Entropy Alloy ◽  
High Entropy Alloys ◽  
Mechanically Alloyed ◽  
High Entropy ◽  
Plasma Sintering ◽  
Conventional Sintering ◽  
Spark Plasma

Tungsten heavy alloy composite was developed by using novel CoCrFeMnNi high-entropy alloy as the binder/reinforcement phase. Elemental tungsten (W) powder and mechanically alloyed CoCrFeMnNi high-entropy alloy were mixed gently in high energy ball mill and consolidated using different sintering process with varying heating rate (in trend of conventional sintering < microwave sintering < spark plasma sintering). Mechanically alloyed CoCrFeMnNi high-entropy alloy have shown a predominant face-centered cubic (fcc) phase with minor Cr-rich σ-phase. Consolidated tungsten heavy high-entropy alloys (WHHEA) composites reveal the presence of Cr–Mn-rich oxide phase in addition to W-grains and high-entropy alloys (HEA) phase. An increase in heating rate restricts the tungsten grain growth with reduces the volume fraction of the Cr–Mn-rich phase. Finally, spark plasma sintering with a higher heating rate and shorter sintering time has revealed higher compressive strength (~2041 MPa) than the other two competitors (microwave sintering: ~1962 MPa and conventional sintering: ~1758 MPa), which may be attributed to finer W-grains and reduced fraction of Cr–Mn rich oxide phase.

Compression stress strengthening modelling of a ultrafine-grained equiatomic SPS CoCrFeNiNb high-entropy alloy

2020 ◽  
pp. 095440622094324
Author(s):  
Marcello Cabibbo ◽  
Filip Průša ◽  
Alexandra Šenková ◽  
Andrea Školáková ◽  
Vojtěch Kučera ◽  
...  
Keyword(s):  
Powder Metallurgy ◽  
Mechanical Alloying ◽  
Oxide Phase ◽  
High Entropy Alloy ◽  
Induction Melting ◽  
High Entropy Alloys ◽  
High Entropy ◽  
Plasma Sintering ◽  
Transmission Electron ◽  
Spark Plasma

High-entropy alloys are known to show exceptionally high mechanical properties, both compression and tensile strength, and unique physical properties, such as their phase stability. These quite unusual properties are primarily due to the microstructure generated by mechanical alloying processes, such as conventional induction arc melting, powder metallurgy, or mechanical alloying. In the present study, an equiatomic CoCrFeNiNb high-entropy alloy was prepared by a sequence of conventional induction melting, powder metallurgy, and compaction via spark plasma sintering. The high-entropy alloys showed uniform sub-micrometer grain microstructure consisted by a mixture of an fcc solid solution strengthened by a hcp Laves phase and a third intergranular oxide phase. The as-cast high-entropy alloys showed an ultimate compression strength (UCS) of ∼1400 MPa, which after sintering and compaction at 1273 K increased up to ∼2400 MPa. Extensive transmission electron microscopy quantitative analyses were carried out to model the UCS. A quite good agreement between the microstructure-strengthening model and the experimental UCS was found.

scholarly journals Application of Hydride Process in Achieving Equimolar TiNbZrHfTa BCC Refractory High Entropy Alloy

Crystals ◽  
2020 ◽  
Vol 10 (11) ◽  
pp. 1020 ◽  
Author(s):  
Bhupendra Sharma ◽  
Kentaro Nagano ◽  
Kuldeep Kumar Saxena ◽  
Hiroshi Fujiwara ◽  
Kei Ameyama
Keyword(s):  
Titanium Hydride ◽  
Single Phase ◽  
Strengthening Mechanism ◽  
High Entropy Alloy ◽  
Mechanically Alloyed ◽  
High Entropy ◽  
Plasma Sintering ◽  
Bcc Structure ◽  
Spark Plasma ◽  
Tih2 Powder

For the first time, an equiatomic refractory high entropy alloy (RHEA) TiNbZrHfTa compact with a single-phase body-centered cubic (BCC) structure was fabricated via a titanium hydride (TiH2) assisted powder metallurgy approach. The constituent pure Ti, Zr, Nb, Hf, and Ta powders were mechanically alloyed (MA) with titanium hydride (TiH2) powder. The resultant MA powder was dehydrogenated at 1073 K for 3.6 ks and subsequently sintered through spark plasma sintering (SPS). Additionally, TiNbZrHfTa counterparts were prepared from pure elements without MA with TiH2. It was observed that the compact prepared from pure powders had a chemically heterogeneous microstructure with hexagonal close packed (HCP) and dual BCC phases. On the other hand, despite containing many constituents, the compact fabricated at 1473 K for 3.6 ks via the hydride approach had a single-phase BCC structure. The Vickers microhardness of the TiNbZrHfTa alloy prepared via the hydride process was Hv 520 (±30). The exceptional microhardness of the alloy is greater than any individual constituent, suggesting the operation of a simple solid-solution-like strengthening mechanism and/or precipitation hardening. In addition, the heat treatments were also carried out to analyze the phase stability of TiNbZrHfTa prepared via the hydride process. The results highlight the substantial changes in the phase as a function of temperature and/or time.

scholarly journals Refractory CrMoNbWV High-Entropy Alloy Manufactured by Mechanical Alloying and Spark Plasma Sintering: Evolution of Microstructure and Properties

Materials ◽  
2021 ◽  
Vol 14 (3) ◽  
pp. 621
Author(s):  
Nikolay Razumov ◽  
Tagir Makhmutov ◽  
Artem Kim ◽  
Boris Shemyakinsky ◽  
Aleksey Shakhmatov ◽  
...  
Keyword(s):  
Solid Solution ◽  
Spark Plasma Sintering ◽  
High Hardness ◽  
High Entropy Alloy ◽  
Mechanically Alloyed ◽  
Laves Phases ◽  
High Entropy ◽  
Electrochemical Tests ◽  
Plasma Sintering ◽  
Spark Plasma

In this study, bulk samples of a CrMoNbWV high-entropy alloy (HEA) were obtained for the first time by spark plasma sintering (SPS) of mechanically alloyed (MA) powders at 1200 °C, 1300 °C, and 1400 °C. Microstructure evolution, phase formation as well as wear and corrosion behavior were investigated. The MA powders’ phase composition was found to be represented by body-centered-cubic (BCC) solid solution. The solid solution partially decomposed to Laves phases under the sintering, such as Cr2Nb and (Fe, Cr)Nb, and NbVO4-VO oxides mixture. The temperature increase to 1400 °C led to a grain coarsening of the BCC phase and decreased the Laves phase content accompanied by precipitation at the grain boundaries. The sintered samples showed high hardness and compressive strength (2700–2800 MPa) at room temperature. The wear tests demonstrated excellent results in comparison to conventional wear-resistant composites. The obtained samples also exhibited high corrosion resistance under electrochemical tests in H2SO4 solution. The CrMoNbWV HEA has comparable mechanical and corrosive properties with the WNbMoTaV type HEA, but at the same time has a reduced density: CrMoNbWV—10.55 g/cm3, WNbMoTaV—12.42 g/cm3.

scholarly journals Vacuum brazing of Al2O3 and 3D printed Ti6Al4V lap-joints using high entropy driven AlZnCuFeSi filler

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Ashutosh Sharma ◽  
Byungmin Ahn
Keyword(s):  
Strength Properties ◽  
Lap Joints ◽  
High Entropy Alloy ◽  
Face Centered Cubic ◽  
High Entropy ◽  
Plasma Sintering ◽  
Spark Plasma ◽  
3D Printed ◽  
Face Centered ◽  
Alloy Filler

AbstractIn this work, we studied the brazing characteristics of Al2O3 and 3D printed Ti–6Al–4V alloys using a novel equiatomic AlZnCuFeSi high entropy alloy filler (HEAF). The HEAF was prepared by mechanical alloying of the constituent powder and spark plasma sintering (SPS) approach. The filler microstructure, wettability and melting point were investigated. The mechanical and joint strength properties were also evaluated. The results showed that the developed AlZnCuFeSi HEAF consists of a dual phase (Cu–Zn, face-centered cubic (FCC)) and Al–Fe–Si rich (base centered cubic, BCC) phases. The phase structure of the (Cu–Al + Ti–Fe–Si)/solid solution promises a robust joint between Al2O3 and Ti–6Al–4V. In addition, the joint interfacial reaction was found to be modulated by the brazing temperature and time because of the altered activity of Ti and Zn. The optimum shear strength reached 84 MPa when the joint was brazed at 1050 °C for 60 s. The results can be promising for the integration of completely different materials using the entropy driven fillers developed in this study.

Sign in / Sign up

Export Citation Format

Share Document