scholarly journals Vibration Energy Harvester Based on Torsionally Oscillating Magnet

Micromachines ◽  
2021 ◽  
Vol 12 (12) ◽  
pp. 1545
Author(s):  
Xinyi Wang ◽  
Jiaxing Li ◽  
Chenyuan Zhou ◽  
Kai Tao ◽  
Dayong Qiao ◽  
...  
Keyword(s):  
Energy Harvester ◽  
Proof Mass ◽  
Vibrational Energy ◽  
Open Circuit ◽  
Vibration Energy ◽  
Peak Voltage ◽  
Vibration Energy Harvester ◽  
Energy Harvesters ◽  
Cantilever Structure ◽  
Sinusoidal Excitation

Most of the miniaturized electromagnetic vibrational energy harvesters (EVEHs) are based on oscillating proof mass suspended by several springs or a cantilever structure. Such structural feature limits the miniaturization of the device’s footprint. This paper presents an EVEH device based on a torsional vibrating magnet over a stack of flexible planar coils. The torsional movement of the magnet is enabled by microfabricated silicon torsional springs, which effectively reduce the footprint of the device. With a size of 1 cm × 1 cm × 1.08 cm, the proposed EVEH is capable of generating an open-circuit peak-to-peak voltage of 169 mV and a power of 6.9 μW, under a sinusoidal excitation of ±0.5 g (g = 9.8 m/s2) and frequency of 96 Hz. At elevated acceleration levels, the maximum peak-to-peak output voltage is 222 mV under the acceleration of 7 g (±3.5 g).

Field Test and Characteristic Analysis of Railroad Track Vibration Energy Harvester

2019 ◽  
Author(s):  
Jianyong Zuo ◽  
Jie Yu ◽  
Cheng Liu ◽  
Yihao Gu ◽  
Lei Zuo ◽  
...  
Keyword(s):  
Energy Harvesting ◽  
Energy Harvester ◽  
Vibrational Energy ◽  
Railway Track ◽  
Vibration Energy ◽  
Resistive Load ◽  
Characteristic Analysis ◽  
Peak Voltage ◽  
Vibration Energy Harvester ◽  
Energy Harvesting System

Abstract Railroad vibration energy harvester has been researched and developed to harness the energy from the vibration of railway track when the trains pass. The vibrational energy could be transformed into electrical energy using mechanical motion rectification (MMR) mechanism and then further be used to power trackside equipment including sensors and some smart electrical devices. In order to test the performance of the MMR railroad energy harvesting system, a series of infield tests were conducted with a self-developed distributed measurement system in Railroad Test Lab at Tongji University. A 10V peak voltage was achieved with 8 Ohms external resistive load at the train speed of 30 km/h, which was consistent with the result of in-lab bench tests. In addition, some experience of design and installation for the motioned based energy harvesting system was gained, which can provide some references for the future improvement of railroad energy harvesting systems.

scholarly journals The Effect of Axial Displacement of Magnets in Piezoelectric Energy Harvester

2018 ◽  
Vol 7 (3.7) ◽  
pp. 95
Author(s):  
Li Wah Thong ◽  
Yu Jing Bong ◽  
Swee Leong Kok ◽  
Roszaidi Ramlan
Keyword(s):  
Frequency Spectrum ◽  
Power Output ◽  
Energy Harvester ◽  
Vibrational Energy ◽  
Vibration Energy ◽  
Vibration Energy Harvester ◽  
Energy Harvesters ◽  
Piezoelectric Energy ◽  
Operational Frequency ◽  
And Performance

The utilization of vibration energy harvesters as a substitute to batteries in wireless sensors has shown prominent interest in the literature. Various approaches have been adapted in the energy harvesters to competently harvest vibrational energy over a wider spectrum of frequencies with optimize power output.   A typical bistable piezoelectric energy harvester, where the influence of magnetic field is induced into a linear piezoelectric cantilever, is designed and analyzed in this paper. The exploitations of the magnetic force specifically creates nonlinear response and bistability in the energy harvester that extends the operational frequency spectrum for optimize performance.  Further analysis on the effects of axial spacing displacement between two repulsive magnets of the harvester, in terms of x-axis (horizontal) and z-axis (vertical) on its natural resonant frequency and performance based on the frequency response curve are investigated for realizing optimal power output. Experimental results show that by selecting the optimal axial spacing displacement, the vibration energy harvester can be designed to produce maximized output power in an improved broadband of frequency spectrum.  

scholarly journals A Pendulum-Like Low Frequency Electromagnetic Vibration Energy Harvester Based on Polymer Spring and Coils

Polymers ◽  
2021 ◽  
Vol 13 (19) ◽  
pp. 3380
Author(s):  
Yunjia Li ◽  
Xinyi Wang ◽  
Shuhan Zhang ◽  
Chenyuan Zhou ◽  
Dayong Qiao ◽  
...  
Keyword(s):  
Resonant Frequency ◽  
Output Voltage ◽  
Degrees Of Freedom ◽  
Energy Harvester ◽  
Vibrational Energy ◽  
Low Frequency ◽  
Open Circuit ◽  
Vibration Energy ◽  
Vibration Energy Harvester ◽  
Circuit Output

This paper presents a low-frequency electromagnetic vibrational energy harvester (EVEH) with two degrees of freedom and two resonant modes. The proposed EVEH is based on a disc magnet suspended in a pendulum fashion by a polymeric spring between two sets of polymer coil stacks. The fabricated EVEH is capable of harvesting vibration energy on two directions with an extended bandwidth. With a sinusoidal acceleration of ±1 g on Z direction, a peak-to-peak closed-circuit output voltage of 0.51 V (open-circuit voltage: 1 V), and an output power of 35.1 μW are achieved at the resonant frequency of 16 Hz. With a sinusoidal acceleration of ±1.5 g on X direction, a peak-to-peak output voltage of 0.14 V and power of 2.56 μW are achieved, at the resonant frequency of 20 Hz.

Simply supported FPEDs connected by springs for broadband energy harvesting

2020 ◽  
Vol 64 (1-4) ◽  
pp. 201-210
Author(s):  
Yoshikazu Tanaka ◽  
Satoru Odake ◽  
Jun Miyake ◽  
Hidemi Mutsuda ◽  
Atanas A. Popov ◽  
...  
Keyword(s):  
Energy Harvesting ◽  
Evaluation Method ◽  
Energy Harvester ◽  
Vibrational Energy ◽  
Functional Materials ◽  
Vibration Energy ◽  
Theoretical Evaluation ◽  
Vibration Energy Harvester ◽  
Polyvinylidene Difluoride ◽  
Simply Supported

Energy harvesting methods that use functional materials have attracted interest because they can take advantage of an abundant but underutilized energy source. Most vibration energy harvester designs operate most effectively around their resonant frequency. However, in practice, the frequency band for ambient vibrational energy is typically broad. The development of technologies for broadband energy harvesting is therefore desirable. The authors previously proposed an energy harvester, called a flexible piezoelectric device (FPED), that consists of a piezoelectric film (polyvinylidene difluoride) and a soft material, such as silicon rubber or polyethylene terephthalate. The authors also proposed a system based on FPEDs for broadband energy harvesting. The system consisted of cantilevered FPEDs, with each FPED connected via a spring. Simply supported FPEDs also have potential for broadband energy harvesting, and here, a theoretical evaluation method is proposed for such a system. Experiments are conducted to validate the derived model.

scholarly journals Dynamic Modeling and Structural Optimization of a Bistable Electromagnetic Vibration Energy Harvester

Energies ◽  
2019 ◽  
Vol 12 (12) ◽  
pp. 2410 ◽  
Author(s):  
Bei Zhang ◽  
Qichang Zhang ◽  
Wei Wang ◽  
Jianxin Han ◽  
Xiaoli Tang ◽  
...  
Keyword(s):  
Energy Harvester ◽  
Vibration Energy ◽  
Vibration Energy Harvester ◽  
Energy Harvesters ◽  
Electromagnetic Vibration ◽  
Magnetic Spring ◽  
Element Simulation ◽  
Nonlinear Galerkin Method ◽  
Simulation And Experiment ◽  
The Mathematical Model

A novel bistable electromagnetic vibration energy harvester (BEMH) is constructed and optimized in this study, based on a nonlinear system consisting mainly of a flexible membrane and a magnetic spring. A large-amplitude transverse vibration equation of the system is established with the general nonlinear geometry and magnetic force. Firstly, the mathematical model, considering the higher-order nonlinearities given by nonlinear Galerkin method, is applied to a membrane with a co-axial magnet mass and magnetic spring. Secondly, the steady vibration response of the membrane subjected to a harmonic base motion is obtained, and then the output power considering electromagnetic effect is analytically derived. On this basis, a parametric study in a broad frequency domain has been achieved for the BEMH with different radius ratios and membrane thicknesses. It is demonstrated that model predictions are both in close agreement with results from the finite element simulation and experiment data. Finally, the proposed efficient solution method is used to obtain an optimizing strategy for the design of multi-stable energy harvesters with the similar flexible structure.

On Mathematical Modeling of Piezoelectric Energy Harvesters

2014 ◽  
Vol 953-954 ◽  
pp. 655-658 ◽  
Author(s):  
Guang Qing Shang ◽  
Hong Bing Wang ◽  
Chun Hua Sun
Keyword(s):  
Mathematical Modeling ◽  
Energy Harvesting ◽  
Energy Harvester ◽  
Vibration Energy ◽  
Piezoelectric Energy Harvesting ◽  
Vibration Energy Harvester ◽  
Energy Harvesters ◽  
Piezoelectric Energy ◽  
Energy Harvesting System ◽  
Piezoelectric Vibration

Energy harvesting system has become one of important areas of ​​research and develops rapidly. How to improve the performance of the piezoelectric vibration energy harvester is a key issue in engineering applications. There are many literature on piezoelectric energy harvesting. The paper places focus on summarizing these literature of mathematical modeling of piezoelectric energy harvesting, ranging from the linear to nonlinear, from early a single mechanical degree to piezoaeroelastic problems.

Design and Comparison of Micro Electromagnetic Vibration Energy Harvesters

2015 ◽  
Vol 645-646 ◽  
pp. 1223-1232
Author(s):  
Yi Ming Lei ◽  
Zhi Yu Wen ◽  
Li Chen
Keyword(s):  
Energy Harvester ◽  
Load Resistance ◽  
Vibration Energy ◽  
Test Results ◽  
Peak Voltage ◽  
Energy Harvesters ◽  
Electromagnetic Vibration ◽  
Mems Technology ◽  
Electromagnetic Energy Harvesting ◽  
Linear Spring

This paper presents two electromagnetic vibration energy harvesters based on micro-electro-mechanical (MEMS) technology. Two prototypes with different vibration structures were designed and fabricated. The energy harvester includes a permanent magnet attached on vibration structure (resonator) made by Si and a fixed wire-wound coil, with the total volume of 0.9 cm3. Two energy harvesters with different resonator are tested and compared. Experiments show that: in the same acceleration and a load resistance, the resonant frequency of prototype B is approximately 95% of prototype A; The peak-peak voltage and the maximum power of prototype B is 1.6 times and 2.7 times of prototype A respectively. The test results was analyzed simply and it indicated that the electromagnetic energy harvesting with the spring B has better performance; also proved that the potential ability of the non-linear spring could extend the frequency bandwidth and improve output voltage.

Heartbeat Energy Harvesting Using the Fan-Folded Piezoelectric Beam Geometry

2015 ◽  
Author(s):  
M. H. Ansari ◽  
M. Amin Karami
Keyword(s):  
Natural Frequency ◽  
Energy Harvester ◽  
Low Frequency ◽  
Mode Shapes ◽  
Vibration Energy ◽  
Vibration Energy Harvester ◽  
Mechanical Coupling ◽  
Energy Harvesters ◽  
Piezoelectric Energy ◽  
Piezoelectric Beam

A three dimensional piezoelectric vibration energy harvester is designed to generate electricity from heartbeat vibrations. The device consists of several bimorph piezoelectric beams stacked on top of each other. These horizontal bimorph beams are connected to each other by rigid vertical beams making a fan-folded geometry. One end of the design is clamped and the other end is free. One major problem in micro-scale piezoelectric energy harvesters is their high natural frequency. The same challenge is faced in development of a compact vibration energy harvester for the low frequency heartbeat vibrations. One way to decrease the natural frequency is to increase the length of the bimorph beam. This approach is not usually practical due to size limitations. By utilizing the fan-folded geometry, the natural frequency is decreased while the size constraints are observed. The required size limit of the energy harvester is 1 cm by 1 cm by 1 cm. In this paper, the natural frequencies and mode shapes of fan-folded energy harvesters are analytically derived. The electro-mechanical coupling has been included in the model for the piezoelectric beam. The design criteria for the device are discussed.

scholarly journals A Comparison of Methods to Measure the Coupling Coefficient of Electromagnetic Vibration Energy Harvesters

Micromachines ◽  
2019 ◽  
Vol 10 (12) ◽  
pp. 826 ◽  
Author(s):  
Mario Mösch ◽  
Gerhard Fischerauer
Keyword(s):  
Coupling Coefficient ◽  
Energy Harvester ◽  
Electromagnetic Coupling ◽  
Electric Circuit ◽  
Open Circuit ◽  
Measurement Methods ◽  
Vibration Energy ◽  
Simulation Data ◽  
Average Deviation ◽  
Energy Harvesters

Vibration energy harvesters transform environmental vibration energy into usable electrical energy. The transformation is only possible because of a coupling between the mechanical part of the energy harvester and the electric circuit. This paper compares several measurement methods to determine the electromagnetic coupling coefficient. These methods are applied to various implementations of an energy harvester and the results are compared with one another and with simulation data by analyzing the magnetic flux. The average deviation between the measurement methods and the simulation data in our study was 5%. This good agreement validates the methods. Based on this, we recommend determination of the coupling coefficient and the optimum load resistance for maximum power harvesting on the basis of simulations and the open circuit method, because this procedure leads to the shortest measurement times.

An Electromagnetic Frequency Increased Vibration Energy Harvester

2011 ◽  
Vol 403-408 ◽  
pp. 4231-4234 ◽  
Author(s):  
Khalid Ashraf ◽  
Mohd Haris Md Khir ◽  
John Ojur Dennis
Keyword(s):  
Permanent Magnets ◽  
Energy Harvester ◽  
Proof Mass ◽  
Excitation Frequency ◽  
Average Power ◽  
Low Frequency ◽  
High Frequency Oscillation ◽  
Vibration Energy ◽  
Frequency Oscillation ◽  
Vibration Energy Harvester

This paper presents an impact-based frequency increased electromagnetic vibration energy harvester to scavenge energy in a low frequency environment. To realize the novel impact based frequency up-conversion mechanism, a coil has been elastically anchored with a platform on which four permanent magnets are arranged in such a way that a strong closed magnetic flux path, linking the coil, is formed. The proposed scavenger has two dynamics of motion. The first phase is a low frequency oscillation to absorb energy from ambient vibration during which both the coil and magnet act as proof mass and move collectively. The increased proof mass ensures maximization of absorbed energy. After crossing a certain clearance, the platform containing magnetic setup rigidly and supporting the coil elastically, collides with a rigid stopper and bounces back. As a result of this mechanical impact a high frequency oscillation is setup in the coil relative to the magnets during which energy is transferred to electrical domain by electromagnetic induction. A macro-prototype has been build to prove the proposed concept. Initial test results show that the proposed harvester generates a peak voltage of 1 volt across a load of 220 Ω at an excitation frequency of 5 Hz which corresponds to a peak power of 4.5 mW and average power of 660 µW.

Sign in / Sign up

Export Citation Format

Share Document