scholarly journals Effect of Extrusion Temperature on the Physico-Mechanical Properties of Unidirectional Wood Fiber-Reinforced Polylactic Acid Composite (WFRPC) Components Using Fused Deposition Modeling

Polymers ◽  
2018 ◽  
Vol 10 (9) ◽  
pp. 976 ◽  
Author(s):  
Teng-Chun Yang
Keyword(s):  
Mechanical Properties ◽  
Polylactic Acid ◽  
Fused Deposition Modeling ◽  
Wood Fiber ◽  
Color Difference ◽  
Extrusion Temperature ◽  
Fiber Reinforced ◽  
Substantial Impact ◽  
Fused Deposition ◽  
Deposition Modeling

Wood fiber-reinforced polylactic acid (PLA) composites (WFRPCs) were used as a filament to manufacture the unidirectional WFRPC components by means of fused deposition modeling (FDM). The physico-mechanical properties of the WFRPC components printed at different extrusion temperatures (200, 210, 220, and 230 °C) were determined. The results revealed that most of the physical properties (moisture content, surface roughness, water absorption rate, and thickness swelling rate) of the printed WFRPC component were not significantly influenced by extrusion temperature, while its density and color difference increased as the extrusion temperature increased. Additionally, the tensile and flexural properties of the FDM-printed WFRPC component decreased when the extrusion temperature was more than 200 °C, whereas the compressive strength and internal bond strength increased by 15.1% and 24.3%, respectively, when the extrusion temperature was increased from 200 to 230 °C. Furthermore, scanning electronic microscopy (SEM) demonstrated that the fracture surface of the tensile component printed at a higher extrusion temperature exhibited a better compatibility at fiber/PLA interfaces and good adhesion between the extruded filament segments. These results indicate that the FDM printing process using different extrusion temperatures has a substantial impact on the surface color, density, and mechanical properties of the printed WFRPC component.

Property Enhancement of Carbon Fiber-Reinforced Polylactic Acid Composites Prepared by Fused-Deposition Modeling

2020 ◽  
pp. 455-478
Author(s):  
Pravin R. Kubade ◽  
Hrushikesh B. Kulkarni ◽  
Vinayak C. Gavali
Keyword(s):  
Mechanical Properties ◽  
Additive Manufacturing ◽  
Carbon Fiber ◽  
Polylactic Acid ◽  
Fused Deposition Modeling ◽  
Three Dimensional ◽  
Fiber Reinforced ◽  
Fused Deposition ◽  
Deposition Modeling ◽  
Properties Of Composites

Additive Manufacturing or three-dimensional printing refers to a process of building lighter, stronger three-dimensional parts, manufactured layer by layer. Additive manufacturing uses a computer and CAD software which passes the program to the printer to build the desired shape. Metals, thermoplastic polymers, and ceramics are the preferred materials used for additive manufacturing. Fused deposition modeling is one additive manufacturing technique involving the use of thermoplastic polymer for creating desired shape. Carbon fibers can be added into polymer to strengthen the composite without adding additional weight. Present work deals with the manufacturing of Carbon fiber-reinforced Polylactic Acid composites prepared using fused deposition modeling. Mechanical and thermo-mechanical properties of composites are studied as per ASTM standards and using sophisticated instruments. It is observed that there is enhancement in thermo-mechanical properties of composites due to addition reinforcement which is discussed in detail.

scholarly journals Morphology and Mechanical Properties of 3D Printed Wood Fiber/Polylactic Acid Composite Parts Using Fused Deposition Modeling (FDM): The Effects of Printing Speed

Polymers ◽  
2020 ◽  
Vol 12 (6) ◽  
pp. 1334 ◽  
Author(s):  
Teng-Chun Yang ◽  
Chin-Hao Yeh
Keyword(s):  
Mechanical Properties ◽  
Polylactic Acid ◽  
Fused Deposition Modeling ◽  
Wood Fiber ◽  
Wood Fibers ◽  
Surface Color ◽  
Fused Deposition ◽  
Deposition Modeling ◽  
Printing Speed ◽  
Morphology And Mechanical Properties

In this study, a wood fiber/polylactic acid composite (WPC) filament was used as feedstock to print the WPC part by means of fused deposition modeling (FDM). The morphology and mechanical properties of WPC parts printed at different speeds (30, 50, and 70 mm/s) were determined. The results show that the density of the printed WPC part increased as the printing speed decreased, while its surface color became darker than that of parts printed at a high speed. The printing time decreased with an increasing printing speed; however, there was a small difference in the time saving percentage without regard to the dimensions of the printed WPC part at a given printing speed. Additionally, the tensile and flexural properties of the printed WPC part were not significantly influenced by the printing speed, whereas the compressive strength and modulus of the FDM-printed part significantly decreased by 34.3% and 14.6%, respectively, when the printing speed was increased from 30 to 70 mm/s. Furthermore, scanning electronic microscopy (SEM) illustrated that the FDM process at a high printing speed produced an uneven surface of the part with a narrower width of printed layers, and pull-outs of wood fibers were more often observed on the fracture surface of the tensile sample. These results show that FDM manufacturing at different printing speeds has a substantial effect on the surface color, surface roughness, density, and compressive properties of the FDM-printed WPC part.

scholarly journals Use of Data Mining Techniques for the Prediction of Surface Roughness of Printed Parts in Polylactic Acid (PLA) by Fused Deposition Modeling (FDM): A Practical Application in Frame Glasses Manufacturing

Polymers ◽  
2020 ◽  
Vol 12 (4) ◽  
pp. 840
Author(s):  
Esther Molero ◽  
Juan Jesús Fernández ◽  
Oscar Rodríguez-Alabanda ◽  
Guillermo Guerrero-Vaca ◽  
Pablo E. Romero
Keyword(s):  
Data Mining ◽  
Surface Roughness ◽  
Polylactic Acid ◽  
Fused Deposition Modeling ◽  
Extrusion Temperature ◽  
Practical Application ◽  
Direction Parallel ◽  
Layer Height ◽  
Fused Deposition ◽  
Deposition Modeling

In the present work, ten data mining algorithms have been used to generate models capable of predicting the surface roughness of parts printed on polylactic acid (PLA) by using fused deposition modeling (FDM). The models have been trained using experimental data measured on 27 horizontal (XY) and 27 vertical (XZ) specimens, printed using different values for the parameters studied (layer height, extrusion temperature, print speed, print acceleration and flow). The models generated by multilayer perceptron (MLP) and logistic model trees (LMT) have obtained the best results in a cross-validation. Although it does not obtain such optimal results, the J48 algorithm (C4.5) allows the generation of models in the form of a decision tree. These trees permit to determine which print parameters have an influence on the surface roughness. For XY specimens, the surface roughness measured in the direction parallel to the extrusion path (Ra,0,XY ) depends on the flow, the print temperature and the layer height; in the direction perpendicular to the extrusion path, the surface roughness (Ra,90,XY) depends only on the flow. For XZ specimens, the surface roughness measured in the direction parallel to the extrusion path (Ra,0,XZ) depends only on the print speed; in the direction perpendicular to the extrusion path (Ra,90,XZ), it depends on the layer height and the extrusion temperature. According to the study carried out, the most suitable set up provides values of Ra,0,XY, Ra,90,XY, Ra,0,XZ and Ra,90,XZ equal to 0.46, 1.18, 0.45 and 11.54, respectively. A practical application of this work is the manufacture of PLA frame glasses using FDM.

Improving mechanical properties of continuous fiber-reinforced thermoplastic composites produced by FDM 3D printer

2018 ◽  
Vol 38 (3) ◽  
pp. 99-116 ◽  
Author(s):  
Behnam Akhoundi ◽  
Amir Hossein Behravesh ◽  
Arvin Bagheri Saed
Keyword(s):  
Mechanical Properties ◽  
Fused Deposition Modeling ◽  
Thermoplastic Composites ◽  
3D Printer ◽  
Fiber Reinforced ◽  
Continuous Fiber ◽  
Fiber Volume ◽  
Fused Deposition ◽  
Deposition Modeling ◽  
Consistent Method

The main purpose of this research is to bolster mechanical properties of the parts, produced by an extrusion-based 3D printer, or fused deposition modeling machine, via increasing the content of continuous fiber yarn to its practical limit. In-melt continuous glass fiber yarn embedding was applied as a reliable and consistent method for simultaneous impregnation to produce continuous fiber-reinforced thermoplastic composites in the fused deposition modeling process. It is well known that the main weakness in the fused deposition modeling 3D printed products is their low strength compared to the manufactured ones by conventional methods such as injection molding and machining processes. This characteristic can be related to both inherent weakness of thermoplastic materials and poor adhesion between the deposited rasters and the layers. Although various attempts have been performed to tackle this issue, it is widely believed that using continuous fibers is the most effective method to serve this purpose if a reliable and consistent method is implemented. Since the mechanical properties of continuous fiber-reinforced composites directly depend on the content of fiber volume, maximizing the fiber content as well as producing an integrated part was assumed as the main objective. In this work, an analysis of various patterns of raster deposition was conducted, followed by the experiments and verification. The effective parameters on the fiber yarn volume, such as fiber yarn diameter, fiber yarn laying pattern, extrusion width, layer height, and flow percentage, were investigated and their optimal values were reported. The attained experimental results showed that, for polylactic acid-glass fiber yarn reinforced composite, with the extrusion width of 0.3 mm, the layer heights of 0.22 mm, flow percentage of 0.43, and the rectangular laying pattern, approximately 50% fiber-volume content can be achieved which resulted in tensile yield strength and modulus of 478 MPa and 29.4 GPa, respectively. There was an excellent agreement between these experimental results and predicted theoretically values by rule of mixture.

scholarly journals 3D Printing of Fiber-Reinforced Plastic Composites Using Fused Deposition Modeling: A Status Review

Materials ◽  
2021 ◽  
Vol 14 (16) ◽  
pp. 4520
Author(s):  
Salman Pervaiz ◽  
Taimur Ali Qureshi ◽  
Ghanim Kashwani ◽  
Sathish Kannan
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
3D Printing ◽  
Fused Deposition Modeling ◽  
Fiber Reinforced Polymers ◽  
Fiber Reinforced ◽  
Reinforced Polymers ◽  
Fused Deposition ◽  
Frp Composites ◽  
Deposition Modeling

Composite materials are a combination of two or more types of materials used to enhance the mechanical and structural properties of engineering products. When fibers are mixed in the polymeric matrix, the composite material is known as fiber-reinforced polymer (FRP). FRP materials are widely used in structural applications related to defense, automotive, aerospace, and sports-based industries. These materials are used in producing lightweight components with high tensile strength and rigidity. The fiber component in fiber-reinforced polymers provides the desired strength-to-weight ratio; however, the polymer portion costs less, and the process of making the matrix is quite straightforward. There is a high demand in industrial sectors, such as defense and military, aerospace, automotive, biomedical and sports, to manufacture these fiber-reinforced polymers using 3D printing and additive manufacturing technologies. FRP composites are used in diversified applications such as military vehicles, shelters, war fighting safety equipment, fighter aircrafts, naval ships, and submarine structures. Techniques to fabricate composite materials, degrade the weight-to-strength ratio and the tensile strength of the components, and they can play a critical role towards the service life of the components. Fused deposition modeling (FDM) is a technique for 3D printing that allows layered fabrication of parts using thermoplastic composites. Complex shape and geometry with enhanced mechanical properties can be obtained using this technique. This paper highlights the limitations in the development of FRPs and challenges associated with their mechanical properties. The future prospects of carbon fiber (CF) and polymeric matrixes are also mentioned in this study. The study also highlights different areas requiring further investigation in FDM-assisted 3D printing. The available literature on FRP composites is focused only on describing the properties of the product and the potential applications for it. It has been observed that scientific knowledge has gaps when it comes to predicting the performance of FRP composite parts fabricated under 3D printing (FDM) techniques. The mechanical properties of 3D-printed FRPs were studied so that a correlation between the 3D printing method could be established. This review paper will be helpful for researchers, scientists, manufacturers, etc., working in the area of FDM-assisted 3D printing of FRPs.

Effect of Printing Parameters on the Mechanical Properties of Parts Fabricated with Open-Source 3D Printers in PLA by Fused Deposition Modeling

2020 ◽  
Vol 22 (4) ◽  
pp. 895-908
Author(s):  
M. Ouhsti ◽  
B. El Haddadi ◽  
S. Belhouideg
Keyword(s):  
Mechanical Properties ◽  
Polylactic Acid ◽  
Fused Deposition Modeling ◽  
Acrylonitrile Butadiene Styrene ◽  
Fused Deposition Modelling ◽  
Fused Deposition ◽  
3D Printers ◽  
Deposition Modeling ◽  
Printed Materials ◽  
Printing Parameters

Abstract3D polymer-based printers have become easily accessible to the public. Usually, the technology used by these 3D printers is Fused Deposition Modelling (FDM). The majority of these 3D printers mainly use acrylonitrile butadiene styrene (ABS) and polylactic acid (PLA) to fabricate 3D objects. In order for the printed parts to be useful for specific applications, the mechanical properties of the printed parts must be known. The aim of this study is to determine the tensile strength and elastic modulus of printed materials in polylactic acid (PLA) according to three important printing parameters such as deposition angle, extruder temperature and printing speed. The central composite design (CCD) was used to reduce the number of tensile test experiments. The obtained results show that the mechanical properties of printed parts depend on printing parameters. Empirical models relating response and process parameters are developed. The analysis of variance (ANOVA) was used to test the validity of models relating response and printing parameters. The optimal printing parameters are determined for the desired mechanical properties.

Sign in / Sign up

Export Citation Format

Share Document