scholarly journals Mechanical Properties of 3D-Printed Acrylonitrile–Butadiene–Styrene TiO2 and ATO Nanocomposites

Polymers ◽  
2020 ◽  
Vol 12 (7) ◽  
pp. 1589 ◽  
Author(s):  
Nectarios Vidakis ◽  
Markos Petousis ◽  
Athena Maniadi ◽  
Emmanuel Koudoumas ◽  
Marco Liebscher ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Mechanical Performance ◽  
Sno2 Nanoparticles ◽  
Three Dimensional ◽  
Acrylonitrile Butadiene Styrene ◽  
International Standards ◽  
Fused Filament Fabrication ◽  
Melt Mixing ◽  
3D Printed ◽  
Butadiene Styrene

In order to enhance the mechanical performance of three-dimensional (3D) printed structures fabricated via commercially available fused filament fabrication (FFF) 3D printers, novel nanocomposite filaments were produced herein following a melt mixing process, and further 3D printed and characterized. Titanium Dioxide (TiO2) and Antimony (Sb) doped Tin Oxide (SnO2) nanoparticles (NPs), hereafter denoted as ATO, were selected as fillers for a polymeric acrylonitrile butadiene styrene (ABS) thermoplastic matrix at various weight % (wt%) concentrations. Tensile and flexural test specimens were 3D printed, according to international standards. It was proven that TiO2 filler enhanced the overall tensile strength by 7%, the flexure strength by 12%, and the micro-hardness by 6%, while for the ATO filler, the corresponding values were 9%, 13%, and 6% respectively, compared to unfilled ABS. Atomic force microscopy (AFM) revealed the size of TiO2 (40 ± 10 nm) and ATO (52 ± 11 nm) NPs. Raman spectroscopy was performed for the TiO2 and ATO NPs as well as for the 3D printed nanocomposites to verify the polymer structure and the incorporated TiO2 and ATO nanocrystallites in the polymer matrix. The scope of this work was to fabricate novel nanocomposite filaments using commercially available materials with enhanced overall mechanical properties that industry can benefit from.

scholarly journals 3D Printed Hierarchical Honeycombs with Carbon Fiber and Carbon Nanotube Reinforced Acrylonitrile Butadiene Styrene

2021 ◽  
Vol 5 (2) ◽  
pp. 62
Author(s):  
Michel Theodor Mansour ◽  
Konstantinos Tsongas ◽  
Dimitrios Tzetzis
Keyword(s):  
Carbon Fibers ◽  
Mechanical Performance ◽  
Acrylonitrile Butadiene Styrene ◽  
Experimental Tests ◽  
Fused Filament Fabrication ◽  
Element Analysis ◽  
Compression Performance ◽  
Honeycomb Structures ◽  
3D Printed ◽  
Butadiene Styrene

The mechanical properties of Fused Filament Fabrication (FFF) 3D printed specimens of acrylonitrile butadiene styrene (ABS), ABS reinforced with carbon fibers (ABS/CFs) and ABS reinforced with carbon nanotubes (ABS/CNTs) are investigated in this paper using various experimental tests. In particular, the mechanical performance of the fabricated specimens was determined by conducting compression and cyclic compression testing, as well as nanoindentation tests. In addition, the design and the manufacturing of hierarchical honeycomb structures are presented using the materials under study. The 3D printed honeycomb structures were examined by uniaxial compressive tests to review the mechanical behavior of such cellular structures. The compressive performance of the hierarchical honeycomb structures was also evaluated with finite element analysis (FEA) in order to extract the stress-strain response of these structures. The results revealed that the 2nd order hierarchy displayed increased stiffness and strength as compared with the 0th and the 1st hierarchies. Furthermore, the addition of carbon fibers in the ABS matrix improved the stiffness, the strength and the hardness of the FFF printed specimens as well as the compression performance of the honeycomb structures.

scholarly journals Enhanced Mechanical, Thermal and Antimicrobial Properties of Additively Manufactured Polylactic Acid with Optimized Nano Silica Content

Nanomaterials ◽  
2021 ◽  
Vol 11 (4) ◽  
pp. 1012
Author(s):  
Nectarios Vidakis ◽  
Markos Petousis ◽  
Emanuel Velidakis ◽  
Nikolaos Mountakis ◽  
Lazaros Tzounis ◽  
...  
Keyword(s):  
Polylactic Acid ◽  
Three Dimensional ◽  
Antibacterial Properties ◽  
Antimicrobial Properties ◽  
Sio2 Nanoparticles ◽  
International Standards ◽  
Fused Filament Fabrication ◽  
Melt Mixing ◽  
Screening Process ◽  
3D Printed

The scope of this work was to create, with melt mixing compounding process, novel nanocomposite filaments with enhanced properties that industry can benefit from, using commercially available materials, to enhance the performance of three-dimensional (3D) printed structures fabricated via fused filament fabrication (FFF) process. Silicon Dioxide (SiO2) nanoparticles (NPs) were selected as fillers for a polylactic acid (PLA) thermoplastic matrix at various weight % (wt.%) concentrations, namely, 0.5, 1.0, 2.0 and 4.0 wt.%. Tensile, flexural and impact test specimens were 3D printed and tested according to international standards and their Vickers microhardness was also examined. It was proven that SiO2 filler enhanced the overall strength at concentrations up to 1 wt.%, compared to pure PLA. Atomic force microscopy (AFM) was employed to investigate the produced nanocomposite extruded filaments roughness. Raman spectroscopy was performed for the 3D printed nanocomposites to verify the polymer nanocomposite structure, while thermogravimetric analysis (TGA) revealed the 3D printed samples’ thermal stability. Scanning electron microscopy (SEM) was carried out for the interlayer fusion and fractography morphological characterization of the specimens. Finally, the antibacterial properties of the produced nanocomposites were investigated with a screening process, to evaluate their performance against Escherichia coli (E. coli) and Staphylococcus aureus (S. aureus).

Correlation of tribo-mechanical properties of internal geometry structures of fused filament fabrication 3D-printed acrylonitrile butadiene styrene

2020 ◽  
Vol 72 (10) ◽  
pp. 1259-1265
Author(s):  
Mohamad Nordin Mohamad Norani ◽  
Mohd Fadzli Bin Abdollah ◽  
Muhammad Ilman Hakimi Chua Abdullah ◽  
Hilmi Amiruddin ◽  
Faiz Redza Ramli ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Wear Rate ◽  
Peer Review ◽  
Tribological Properties ◽  
Acrylonitrile Butadiene Styrene ◽  
Fused Filament Fabrication ◽  
Content Type ◽  
Internal Geometry ◽  
3D Printed ◽  
Butadiene Styrene

Purpose This study aims is to investigate the correlation between tribological and mechanical properties of the fused filament fabrication 3D-printed acrylonitrile butadiene styrene (ABS) pin with different internal geometries. Design/methodology/approach The tribological properties were determined by a dry sliding test with constant test parameters, while the hardness and modulus of elasticity were determined by microhardness and compression tests. Findings Although the internal geometry of the pin sample slightly affects the coefficient of friction (COF) and the wear rate of the 3D-printed ABS, it was important to design a lightweight tribo-component by reducing the material used to save energy without compromising the strength of the component. The COF and wear rate values are relatively dependent on the elastic modulus. A 3D-printed ABS pin with an internal triangular flip structure was found to have the shortest run-in period and the lowest COF with high wear resistance. Abrasive wear and delamination are the predominant wear mechanisms involved. Research limitations/implications The findings are the subject of future research under various sliding conditions by investigating the synergistic effect of sliding speeds and applied loads to validate the results of this study. Originality/value The internal structure affects the mechanical properties and release stress concentration at the contact point, resulting in hypothetically low friction and wear. This approach may also reduce the weight of the parts without scarifying or at least preserving their preceding tribological performance. Therefore, based on our knowledge, limited studies have been conducted for the application of 3D printing in tribology, and most studies focused on improving their mechanical properties rather than correlating them with tribological properties that would benefit longer product lifespans. Peer review The peer review history for this article is available at: https://publons.com/publon/10.1108/ILT-04-2020-0143/

scholarly journals The mechanical performance of 3D printed hierarchical honeycombs using carbon fiber and carbon nanotube reinforced acrylonitrile butadiene styrene filaments

2020 ◽  
Vol 318 ◽  
pp. 01049
Author(s):  
Michel Theodor Mansour ◽  
Konstantinos Tsongas ◽  
Dimitris Tzetzis
Keyword(s):  
Carbon Fiber ◽  
Carbon Fibers ◽  
Mechanical Performance ◽  
Acrylonitrile Butadiene Styrene ◽  
Compression Tests ◽  
Fused Filament Fabrication ◽  
Element Analysis ◽  
3D Printed ◽  
Experimental Findings ◽  
Butadiene Styrene

The aim of this paper is to design hierarchical honeycombs as well as manufacturing such structures with a commercial 3D Printer using Fused Filament Fabrication (FFF) technique. The materials under study are commercial filaments such as acrylonitrile butadiene styrene (ABS), acrylonitrile butadiene styrene/carbon fibers (ABS/CF) and acrylonitrile butadiene styrene/carbon nanotubes (ABS/CNTs). The fabricated hierarchical honeycombs were examined by compression tests in order to evaluate the mechanical behaviour of such honeycomb 3D printed structures. The compression behaviour of the hierarchical honeycombs was assessed also with finite element analysis (FEA) and at the end there was a comparison with the experimental findings. The results reveal that the 2nd order hierarchy presented an increase both in stiffness and strength in comparison with the 0th and the 1st hierarchies which make such designs a suitable for structures require such properties. Also, the results reveal that ABS/carbon fiber constructs outperform the other materials under study.

Sign in / Sign up

Export Citation Format

Share Document