scholarly journals Fabrication of Micro-Groove on the Surface of CFRP to Enhance the Connection Strength of Composite Part

Polymers ◽  
2021 ◽  
Vol 13 (22) ◽  
pp. 4039
Author(s):  
Bin Xu ◽  
Meng-Yang Wei ◽  
Xiao-Yu Wu ◽  
Lian-Yu Fu ◽  
Feng Luo ◽  
...  
Keyword(s):  
Tensile Strength ◽  
Injection Molding ◽  
Polymer Material ◽  
Lightweight Design ◽  
Injection Pressure ◽  
Polyamide 6 ◽  
Compression Molding ◽  
Connection Strength ◽  
Molding Process ◽  
Composite Part

Carbon fiber-reinforced plastic (CFRP) has the advantages of being light weight, high strength, and corrosion resistant. At present, it is widely used in the lightweight design of automobile parts. The manufacturing of lightweight parts inevitably involves the connection between CFRP and the polymer material. The connection strength between CFRP and the polymer material significantly affects the service life of the composite parts. Taking CFRP and polyamide 6 (PA6) injection-molded composite parts as an example, this paper proposed a technological method to enhance the connection strength between CFRP and PA6. The proposed method was to fabricate micro-groove structures on the CFRP surface by compression molding. These micro-groove structures effectively increased the injection-molding area of the composite parts, thus enhancing the connection strength between CFRP and PA6. This paper presented a detailed study on the compression-molding process of micro-grooves on the CFRP surface, and successfully obtained the appropriate parameters. Finally, PA6 was used for injection molding on the CFRP with micro-grooves at an injection pressure of 8 MPa, an injection temperature of 240 °C, a holding pressure of 5 MPa, and a holding time of 2.5 s. The experimental results show that the micro-groove array structures on the CFRP surface could effectively improve the tensile strength of the connection interface in the composite parts. Compared with the composite part without micro-grooves, the tensile strength of the composite part with micro-grooves was increased by 80.93%. The composite parts prepared in this paper are mainly used in automobile interiors and the research results of this paper meet the actual needs of the enterprise.

Viscosity Testing of Plastic Material PA6 with 15% of Glass Fibers

2018 ◽  
Vol 928 ◽  
pp. 133-138
Author(s):  
Karel Ráž ◽  
Martin Zahalka
Keyword(s):  
Injection Molding ◽  
Polymer Material ◽  
Process Parameters ◽  
Plastic Material ◽  
Glass Fibers ◽  
Injection Pressure ◽  
Injection Molding Process ◽  
Spiral Flow ◽  
Molding Process ◽  
Melt Temperature

The main aim of this paper was to describe the viscosity and injection mold filling behavior of PA6 with 15% of glass fibers. Injection molding is one of the most widely used processes for polymer products. The quality of these products is directly linked to correct choice of process parameters. It is necessary to understand the filling behavior of the polymer material during the injection molding process. The spiral flow test was carried out in this study to explore the effects of several injection process parameters. The resulting lengths of spiral flow were compared. The polymer material under test was Polyamide 6 with 15% of short glass fibers (trade name: Durethan BKV 15). Virtual testing as well as real testing was performed. A predominantly linear relationship between the flow length and the mold temperature, melt temperature and injection pressure is described here. A special mold was designed for this test.

scholarly journals Effects of Injection Molding Parameters on Properties of Insert-Injection Molded Polypropylene Single-Polymer Composites

Polymers ◽  
2021 ◽  
Vol 14 (1) ◽  
pp. 23
Author(s):  
Jian Wang ◽  
Qianchao Mao ◽  
Nannan Jiang ◽  
Jinnan Chen
Keyword(s):  
Tensile Strength ◽  
Injection Molding ◽  
Injection Pressure ◽  
Holding Time ◽  
Injection Molding Process ◽  
Processing Temperature ◽  
Molding Process ◽  
Multiple Production ◽  
Injection Speed ◽  
Injection Molded

The reinforcement and matrix of a polymer material can be composited into a single polymer composite (SPC), which is light weight, high strength, and has easy recyclability. The insert injection molding process can be used to realize the multiple production of SPC products with a short cycle time and wide processing temperature window. However, injection molding is a very complicated process; the influence of several important parameters should be determined to help in the future tailoring of SPCs to specific applications. The effects of varying barrel temperature, injection pressure, injection speed, and holding time on the properties of the insert-injection molded polypropylene (PP) SPC parts were investigated. It was found that the sample weight and tensile properties of the PP SPCs varied in different rules with the variations of these four parameters. The barrel temperature has a significant effect, followed by the holding time and injection pressure. Suitable parameter values should be determined for enhanced mechanical properties. Based on the tensile strength, a barrel temperature of 260 °C, an injection pressure of 127.6 MPa, an injection speed of 0.18 m/s, and a holding time of 60 s were determined as the optimum processing conditions. The best tensile strength and peel strength were up to 120 MPa and 19.44 N/cm, respectively.

Filling Behavior of Polymer Material into Sub-^|^mu;m Structure in Injection Molding Process

2013 ◽  
Vol 133 (4) ◽  
pp. 105-111
Author(s):  
Chisato Yoshimura ◽  
Hiroyuki Hosokawa ◽  
Koji Shimojima ◽  
Fumihiro Itoigawa
Keyword(s):  
Injection Molding ◽  
Polymer Material ◽  
Injection Molding Process ◽  
Molding Process

scholarly journals Study on Stability of a Novel Binder System Based on Palm Stearin in Metal Injection Moulding Application

2007 ◽  
Vol 4 (2) ◽  
pp. 1
Author(s):  
Muhammad Hussain Ismail ◽  
Norhamidi Muhamad ◽  
Aidah Jumahat ◽  
Istikamah Subuki ◽  
Mohd Afian Omar
Keyword(s):  
Injection Molding ◽  
Flow Characteristics ◽  
Injection Pressure ◽  
Palm Stearin ◽  
Steel Powder ◽  
Metal Injection Molding ◽  
Injection Molding Process ◽  
Binder System ◽  
Molding Process ◽  
Flow Activation Energy

Metal Injection Molding (MIM) is a wellestablished technology for manufacturing a variety of complex and small precision parts. In this paper, fundamental rheological characteristics of MIM feedstock using palm stearin are theoretically analyzed and presented. The feedstock consisted of gas atomized 316L stainless steel powder at three different particle size distributions and the binder system of palm stearin (PS) and polyethylene (PE). The powder loading used was 60vol % for all samples (monosize 16 µm, monosize 45 µm, and bimodal 16 µm + 45 µm) and the binder system of 40vol %(PS/PE = 40/60). The viscosity of MIM feedstock at different temperatures and shear rates was measured and evaluated. Results showed that, the feedstock containing palm stearin exhibited suitable rheological properties by increasing the fluidity of feedstock in MIM process. The rheological results also showed a pseudoplastic flow characteristics, which poses higher value of shear sensitivity (n) and lower value of flow activation energy (E), that are both favourable for injection molding process. The green parts were successfully injected and exhibited adequate strength for handling by optimizing the injection pressure and temperature.

Effects of molding on property of thermally conductive and electrically insulating polyamide 6–based composite

2018 ◽  
Vol 32 (9) ◽  
pp. 1190-1203 ◽  
Author(s):  
Xuping Yang ◽  
Wenbin Yang ◽  
Jinghui Fan ◽  
Juying Wu ◽  
Kai Zhang
Keyword(s):  
Thermal Conductivity ◽  
Tensile Strength ◽  
Injection Molding ◽  
Annealing Time ◽  
Polyamide 6 ◽  
Molding Pressure ◽  
Hot Press ◽  
Molding Method ◽  
Thermally Conductive ◽  
Press Molding

Thermally conductive and electrically insulating polyamide 6 (PA6) matrix quaternary composites were prepared by hot press molding and injection molding, respectively. The quaternary composites were composed of zero-dimensional aluminum oxide particle, one-dimensional silicon carbide whisker, two-dimensional flake graphite, and PA6 resin matrix. Morphology, structure, density, thermal conductivity, volume electrical resistivity, and tensile strength of two types of composites were characterized by scanning electron microscopy, X-ray diffractometer, thermal conductivity tester, high resistance micro-current tester, and tensile tester. The results showed that crystallinity, thermal conductivity, density, and tensile strength of hot press molding samples were superior to those of samples made by injection molding method. This is due to that hot press molding method can provide higher molding pressure and longer annealing time than injection molding. The mechanism could be explained that the performances of the composites were promoted by increasing molding pressure and annealing time.

Application of Moldflow in Gas-Assisted Injection Molding

2011 ◽  
Vol 328-330 ◽  
pp. 1202-1205
Author(s):  
Ke Ming Zi ◽  
Li Heng Chen
Keyword(s):  
Injection Molding ◽  
Volume Fraction ◽  
Injection Pressure ◽  
Processing Technique ◽  
Optimum Process ◽  
Molding Process ◽  
Plastic Processing ◽  
Gas Volume Fraction ◽  
Gas Volume

Gas-assisted injection molding(GAIM)is a new kind of plastic processing technique. It is one of the most important developments in the injection molding industry. GAIM has many advantages such as lower injection pressure, lower warpage, better surface quality, lower material consumption, and shorten molding cycle time, etc. MPI/Gas module of Moldflow software can be used to simulate the GAIM process to optimize the whole molding process. In this study, the FM new truck interior ceiling handle was analyzed in GAIM process based on the MPI/Gas module. The simulation results showed the gas penetrating time, the contours of plastic layers thickness fraction of the parts and the gas volume fraction changing with time. The results can help technicians to determine the optimum process of the melt injection and the gas injection to ensure the final quality of the parts.

Comprehensive Online Control Strategies for Plastic Injection Molding Process

2014 ◽  
Vol 136 (4) ◽  
Author(s):  
Jaho Seo ◽  
Amir Khajepour ◽  
Jan P. Huissoon
Keyword(s):  
Injection Molding ◽  
Injection Pressure ◽  
Thermal Control ◽  
Plastic Injection Molding ◽  
Injection Molding Process ◽  
Molding Process ◽  
Element Analysis ◽  
Thermal Dynamics ◽  
Uncertain Dynamics ◽  
Plastic Injection

This study proposes an effective thermal control for plastic injection molding (polymer: Santoprene 8211-45 with density of 790 kg/m3, injection pressure: 1400 psi (9,652,660 Pa)) in a laminated die. For this purpose, a comprehensive control strategy is provided to cover various themes. First, a new method for determining the optimal sensor locations as a prerequisite step for modeling and controller design is introduced. Second, system identification through offline and online training with finite element analysis and neural network techniques are used to develop an accurate model by incorporating uncertain dynamics of the laminated die. Third, an additive feedforward control by adding direct adaptive inverse control to self-adaptive PID is developed for temperature control of cavity wall (cavity size: 52.9 × 32.07 × 16.03 mm). A verification of designed controller's performance demonstrates that the proposed strategy provides accurate online temperature tracking and faster response under thermal dynamics with various cycle-times in the injection mold process.

Optimizing Injection Parameters of Kenaf Filler Polypropylene Composite by Taguchi Method

2017 ◽  
Vol 894 ◽  
pp. 81-84 ◽  
Author(s):  
Mohd Khairul Fadzly Md Radzi ◽  
Norhamidi Muhamad ◽  
Abu Bakar Sulong ◽  
Zakaria Razak
Keyword(s):  
Injection Molding ◽  
Taguchi Method ◽  
Process Condition ◽  
Injection Pressure ◽  
Poor Quality ◽  
Injection Molding Process ◽  
Molding Process ◽  
Injection Parameters ◽  
Pp Composites ◽  
Injection Temperature

Optimization of injection molding parameters provided a solution to achieve strength improvement of kenaf filler polypropylene composites. Since, molded polymers composites possibility being effected by machine parameters and other process condition that may cause poor quality of composites product. Thus in this study, composite of kenal filler reinforced with thermoplastic polypropylene (PP) were prepared using a sigma blade mixer, followed by an injection molding process. To determine the optimal processing of injection parameters, Taguchi method with L27 orthogonal array was used on statistical analysis of tensile properties of kenaf/PP composites. The results obtained the optimum parameters which were injection temperature 190°C, injection pressure 1300 bar, holding pressure 1900 bar and injection rate 20cm3/s. From the analysis of variance (ANOVA), both flow rate and injection temperature give highest contribution factor to the mechanical properties of the kenaf/PP composites.

Influence of Technological Parameters on Material Flow

2015 ◽  
Vol 1120-1121 ◽  
pp. 1194-1197 ◽  
Author(s):  
Michal Stanek ◽  
David Manas ◽  
Miroslav Manas ◽  
Vojtech Senkerik ◽  
Adam Skrobak ◽  
...  
Keyword(s):  
Injection Molding ◽  
Injection Pressure ◽  
Polymer Processing ◽  
Injection Rate ◽  
Cavity Surface ◽  
Injection Molding Process ◽  
Technological Parameters ◽  
Molding Process ◽  
Processing Technologies

Injection molding is one of the most extended polymer processing technologies. It enables the manufacture of final products, which do not require any further operations. The tools used for their production – the injection molds – are very complicated assemblies that are made using several technologies and materials. Delivery of polymer melts into the mold cavity is the most important stage of the injection molding process. The fluidity of polymers is affected by many parameters Inc. mold design. Evaluation of set of data obtained by experiments in which the testing conditions were widely changed shows that the quality of cavity surface and technological parameters (injection rate, injection pressure and gate size) has substantial influence on the length of flow.

Numerical and Experimental Study on the Injection Moulding of a Thin-Wall Complex Part

2008 ◽  
Author(s):  
Catalin Fetecau ◽  
Ion Postolache ◽  
Felicia Stan
Keyword(s):  
Injection Molding ◽  
Injection Pressure ◽  
Mold Temperature ◽  
Processing Parameters ◽  
Injection Molding Process ◽  
Thin Wall ◽  
Molding Process ◽  
Complex Part ◽  
Filling Time ◽  
Wall Injection

The research presented in this paper involves numerical and experimental efforts to investigate the relative thin-wall injection molding process in order to obtain high dimensional quality complex parts. To better understand the effects of various processing parameters (the filling time, injection pressure, the melting temperature, the mold temperature) on the injection molding of a thin-wall complex part, the molding experiments are regenerated into the computer model using the Moldflow Plastics Insight (MPI) 6.1 software. The computer visualization of the filling phase allows accurate prediction of the location of the flow front, welding lines and air traps. Furthermore, in order to optimize the injection molding process, the effects of the geometry of the runner system on the filling and packing phases are also investigated. It is shown that computational modeling could be used to help the process and mold designer to produce accurate parts.

Sign in / Sign up

Export Citation Format

Share Document