scholarly journals Heat Transfer Enhancement by Coupling of Carbon Nanotubes and SiO2 Nanofluids: A Numerical Approach

Processes ◽  
2019 ◽  
Vol 7 (12) ◽  
pp. 937 ◽  
Author(s):  
Fitnat Saba ◽  
Saima Noor ◽  
Naveed Ahmed ◽  
Umar Khan ◽  
Syed Tauseef Mohyud-Din ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Carbon Nanotubes ◽  
Three Dimensional ◽  
Numerical Approach ◽  
Skin Friction Coefficient ◽  
Squeezing Flow ◽  
Hybrid Nanofluid ◽  
Governing Equations ◽  
Similarity Transformations ◽  
Rotating Channel

This article comprises the study of three-dimensional squeezing flow of (CNT-SiO2/H2O) hybrid nanofluid. The flow is confined inside a rotating channel whose lower wall is stretchable as well as permeable. Heat transfer with viscous dissipation is a main subject of interest. We have analyzed mathematically the benefits of hybridizing SiO 2 -based nanofluid with carbon nanotubes ( CNTs ) nanoparticles. To describe the effective thermal conductivity of the CNTs -based nanofluid, a renovated Hamilton–Crosser model (RHCM) has been employed. This model is an extension of Hamilton and Crosser’s model because it also incorporates the effect of the interfacial layer. For the present flow scenario, the governing equations (after the implementation of similarity transformations) results in a set of ordinary differential equations (ODEs). We have solved that system of ODEs, coupled with suitable boundary conditions (BCs), by implementing a newly proposed modified Hermite wavelet method (MHWM). The credibility of the proposed algorithm has been ensured by comparing the procured results with the result obtained by the Runge-Kutta-Fehlberg solution. Moreover, graphical assistance has also been provided to inspect the significance of various embedded parameters on the temperature and velocity profile. The expression for the local Nusselt number and the skin friction coefficient were also derived, and their influential behavior has been briefly discussed.

scholarly journals Modelling of Applied Magnetic Field and Thermal Radiations Due to the Stretching of Cylinder

Processes ◽  
2021 ◽  
Vol 9 (6) ◽  
pp. 1077
Author(s):  
Muhammad Tamoor ◽  
Muhammad Kamran ◽  
Sadique Rehman ◽  
Aamir Farooq ◽  
Rewayat Khan ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Fluid Velocity ◽  
Three Dimensional ◽  
Numerical Approach ◽  
Skin Friction Coefficient ◽  
Physical Parameters ◽  
Boundary Layer Equations ◽  
Convective Parameter ◽  
Momentum And Heat Transfer ◽  
Dimensional Boundary

In this study, a numerical approach was adopted in order to explore the analysis of magneto fluid in the presence of thermal radiation combined with mixed convective and slip conditions. Using the similarity transformation, the axisymmetric three-dimensional boundary layer equations were reduced to a self-similar form. The shooting technique, combined with the Range–Kutta–Fehlberg method, was used to solve the resulting coupled nonlinear momentum and heat transfer equations numerically. When physically interpreting the data, some important observations were made. The novelty of the present study lies in finding help to control the rate of heat transfer and fluid velocity in any industrial manufacturing processes (such as the cooling of metallic plates). The numerical results revealed that the Nusselt number decrease for larger Prandtl number, curvature, and convective parameters. At the same time, the skin friction coefficient was enhanced with an increase in both slip velocity and convective parameter. The effect of emerging physical parameters on velocity and temperature profiles for a nonlinear stretching cylinder has been thoroughly studied and analyzed using plotted graphs and tables.

scholarly journals Unsteady Transport Phenomena of Hybrid Al2O3-Cu/H2O Nanofluid Past a Shrinking Slender Cylinder

2021 ◽  
Vol 50 (12) ◽  
pp. 3753-3764
Author(s):  
Nurul Amira Zainal ◽  
Roslinda Nazar ◽  
Kohilavani Naganthran ◽  
Ioan Pop
Keyword(s):  
Heat Transfer ◽  
Differential Equations ◽  
Volume Fraction ◽  
Skin Friction Coefficient ◽  
Hybrid Nanofluid ◽  
Similarity Transformations ◽  
Flow And Heat Transfer ◽  
Theoretical Investigations ◽  
Suitable Form ◽  
Layer Flow

Theoretical investigations of unsteady boundary layer flow gain interest due to its relatability to practical settings. Thus, this study proposes a unique mathematical model of the unsteady flow and heat transfer in hybrid nanofluid past a permeable shrinking slender cylinder. The suitable form of similarity transformations is adapted to simplify the complex partial differential equations into a solvable form of ordinary differential equations. A built-in bvp4c function in MATLAB software is exercised to elucidate the numerical analysis for certain concerning parameters, including the unsteadiness and curvature parameters. The bvp4c procedure is excellent in providing more than one solution once sufficient predictions are visible. The present analysis further observed dual solutions that exist in the system of equations. Notable findings showed that by increasing the nanoparticles volume fraction, the skin friction coefficient increases in accordance with the heat transfer rate. In contrast, the decline of the unsteadiness parameter demonstrates a downward trend toward the heat transfer performance.

scholarly journals Unsteady MHD Mixed Convection Flow in Hybrid Nanofluid at Three-Dimensional Stagnation Point

Mathematics ◽  
2021 ◽  
Vol 9 (5) ◽  
pp. 549
Author(s):  
Nurul Amira Zainal ◽  
Roslinda Nazar ◽  
Kohilavani Naganthran ◽  
Ioan Pop
Keyword(s):  
Heat Transfer ◽  
Friction Coefficient ◽  
Differential Equations ◽  
Mixed Convection ◽  
Skin Friction ◽  
Stagnation Point ◽  
Three Dimensional ◽  
Skin Friction Coefficient ◽  
Stagnation Point Flow ◽  
Hybrid Nanofluid

There has been significant interest in exploring a stagnation point flow due to its numerous potential uses in engineering applications such as cooling of nuclear reactors. Hence, this study proposed a numerical analysis on the unsteady magnetohydrodynamic (MHD) mixed convection at three-dimensional stagnation point flow in Al2O3–Cu/H2O hybrid nanofluid over a permeable sheet. The ordinary differential equations are accomplished by simplifying the governing partial differential equations through suitable similarity transformation. The numerical computation is established by the MATLAB system software using the bvp4c technique. The bvp4c procedure is excellent in providing more than one solution once sufficient predictions are visible. The influence of certain functioning parameters is inspected, and notable results exposed that the rate of heat transfer is exaggerated along with the skin friction coefficient while the suction/injection and magnetic parameters are intensified. The results also signified that the rise in the volume fraction of the nanoparticle and the decline of the unsteadiness parameter demonstrates a downward attribution towards the heat transfer performance and skin friction coefficient. Conclusively, the observations are confirmed to have multiple solutions, which eventually contribute to an investigation of the analysis of the solution stability, thereby justifying the viability of the first solution.

scholarly journals Lorentz Forces Effects on the Interactions of Nanoparticles in Emerging Mechanisms with Innovative Approach

Symmetry ◽  
2020 ◽  
Vol 12 (10) ◽  
pp. 1700 ◽  
Author(s):  
Noor Saeed Khan ◽  
Qayyum Shah ◽  
Arif Sohail ◽  
Poom Kumam ◽  
Phatiphat Thounthong ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Entropy Generation ◽  
Volume Fraction ◽  
Dimensional Space ◽  
Three Dimensional ◽  
Leading Edge ◽  
Generation Rate ◽  
Entropy Generation Rate ◽  
Hybrid Nanofluid ◽  
Similarity Transformations

This paper focuses on advances in the understanding of both the fundamental and applied aspects of nanomaterials. Nanoparticles (titania and graphene oxide) in water-based fluid lying on a surface incorporating the leading edge accretion (or ablation) are analyzed. Entropy generation rate is also considered. The Hall current effect is induced in the flow of hybrid nanofluid, due to which the two-dimensional study converts into three-dimensional space. Similarity transformations convert the equations of momentum, heat transfer, nanoparticles volume fraction and boundary conditions into non-dimensional form. Mathematica software is used to obtain the computation through homotopy analysis method. Analysis is provided through the effects of different parameters on different profiles by sketching the graphs. Flow, heat transfer and nanoparticles concentration in TiO2/H2O, as well as GO-TiO2/H2O, are decreased with increasing the Stefan blowing effect, while entropy generation rate elevates upon increasing each parameter. Both of the velocity components are reduced with increasing the Hall parameter. Streamlines demonstrate that trapping is increased at the left side of the surface. The obtained results are compared with the published work which show the authentication of the present work.

Impact of Frictional Heating on MHD Radiative Ferrofluid Past a Convective Shrinking Surface

2017 ◽  
Vol 378 ◽  
pp. 157-174 ◽  
Author(s):  
Anantha Kumar Kempannagari ◽  
Venkata Ramana Reddy Janke ◽  
Sugunamma Vangala ◽  
Sandeep Naramgari
Keyword(s):  
Heat Transfer ◽  
Volume Fraction ◽  
Frictional Heating ◽  
Fluid Velocity ◽  
Skin Friction Coefficient ◽  
Shrinking Sheet ◽  
Physical Parameters ◽  
Governing Equations ◽  
Similarity Transformations ◽  
Shrinking Surface

The intention of this analysis is to analyse the heat transfer impact on MHD ferrofluid flow over a shrinking sheet. This study is carried out under the knowledge of frictional heating, Biot number and thermal radiation. With the assist of suitable similarity transformations, the governing equations are transmuted into coupled nonlinear ODE’s and then numerically solved by R.K. Fehlberg Technique. For this study, we considered the ferrofluid. The behavior of sundry physical parameters on fluid velocity, temperature, skin friction coefficient and local Nusselt number are discussed and presented through plots and tables. Through this investigation, we found that the magnitude of fluid velocity enhances with rising values of volume fraction of nanoparticles. Also, it is found that the Eckert number has tendency to reduce the rate of heat transport.

scholarly journals Unsteady hybrid-nanofluid flow comprising ferrousoxide and CNTs through porous horizontal channel with dilating/squeezing walls

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Muhammad Bilal ◽  
Hamna Arshad ◽  
Muhammad Ramzan ◽  
Zahir Shah ◽  
Poom Kumam
Keyword(s):  
Carbon Nanotubes ◽  
Differential Equations ◽  
Numerical Approach ◽  
Hybrid Nanofluid ◽  
Multi Wall Carbon Nanotubes ◽  
Porous Walls ◽  
Industrial Cleaning ◽  
Energy Equations ◽  
Single Wall Nanotubes ◽  
Order Four

AbstractThe key objective of the present research is to examine the hybrid magnetohydrodynamics (MHD) nanofluid (Carbon-nanotubes and ferrous oxide–water) CNT–Fe3O4/H2 flow into a horizontal parallel channel with thermal radiation through squeezing and dilating porous walls. The parting motion is triggered by the porous walls of the channel. The fluid flow is time-dependent and laminar. The channel is asymmetric and the upper and lower walls are distinct in temperature and are porous. With the combination of nanoparticles of Fe3O4 and single and multi-wall carbon nanotubes, the hybrid nanofluid principle is exploited. By using the similarity transformation, the set of partial differential equations (PDEs) of this mathematical model, governed by momentum and energy equations, is reduced to corresponding ordinary differential equations (ODEs). A very simple numerical approach called the Runge–Kutta system of order four along with the shooting technique is used to achieve the solutions for regulating ODEs. MATLAB computing software is used to create temperature and velocity profile graphs for various emerging parameters. At the end of the manuscript, the main conclusions are summarized. Through different graphs, it is observed that hybrid-nanofluid has more prominent thermal enhancement than simple nanofluid. Further, the single-wall nanotubes have dominated impact on temperature than the multi-wall carbon nanotubes. From the calculations, it is also noted that Fe2O3–MWCNT–water has an average of 4.84% more rate of heat transfer than the Fe2O3–SWCNT–water. On the other hand, 8.27% more heat flow observed in Fe2O3–SWCNT–water than the simple nanofluid. Such study is very important in coolant circulation, inter-body fluid transportation, aerospace engineering, and industrial cleaning procedures, etc.

scholarly journals Numerical simulation of variable thermal conductivity on 3D flow of nanofluid over a stretching sheet

2020 ◽  
Vol 9 (1) ◽  
pp. 233-243 ◽  
Author(s):  
Nainaru Tarakaramu ◽  
P.V. Satya Narayana ◽  
Bhumarapu Venkateswarlu
Keyword(s):  
Heat Transfer ◽  
Thermal Conductivity ◽  
Stretching Sheet ◽  
Three Dimensional ◽  
Variable Thermal Conductivity ◽  
Normal Velocity ◽  
Transfer Coefficients ◽  
Similarity Transformations ◽  
Frictional Coefficients ◽  
The Impact

AbstractThe present investigation deals with the steady three-dimensional flow and heat transfer of nanofluids due to stretching sheet in the presence of magnetic field and heat source. Three types of water based nanoparticles namely, copper (Cu), aluminium oxide (Al2O3), and titanium dioxide (TiO2) are considered in this study. The temperature dependent variable thermal conductivity and thermal radiation has been introduced in the energy equation. Using suitable similarity transformations the dimensional non-linear expressions are converted into dimensionless system and are then solved numerically by Runge-Kutta-Fehlberg scheme along with well-known shooting technique. The impact of various flow parameters on axial and transverse velocities, temperature, surface frictional coefficients and rate of heat transfer coefficients are visualized both in qualitative and quantitative manners in the vicinity of stretching sheet. The results reviled that the temperature and velocity of the fluid rise with increasing values of variable thermal conductivity parameter. Also, the temperature and normal velocity of the fluid in case of Cu-water nanoparticles is more than that of Al2O3- water nanofluid. On the other hand, the axial velocity of the fluid in case of Al2O3- water nanofluid is more than that of TiO2nanoparticles. In addition, the current outcomes are matched with the previously published consequences and initiate to be a good contract as a limiting sense.

Turbine Airfoil Heat Transfer Predictions Using CFD

2005 ◽  
Author(s):  
Anil K. Tolpadi ◽  
James A. Tallman ◽  
Lamyaa El-Gabry
Keyword(s):  
Heat Transfer ◽  
Boundary Layer ◽  
Turbulence Modeling ◽  
Three Dimensional ◽  
Numerical Approach ◽  
Navier Stokes ◽  
Design System ◽  
Computational Fluid Dynamics Cfd ◽  
Turbine Airfoils ◽  
Typical Design

Conventional heat transfer design methods for turbine airfoils use 2-D boundary layer codes (BLC) combined with empiricism. While such methods may be applicable in the mid span of an airfoil, they would not be very accurate near the end-walls and airfoil tip where the flow is very three-dimensional (3-D) and complex. In order to obtain accurate heat transfer predictions along the entire span of a turbine airfoil, 3-D computational fluid dynamics (CFD) must be used. This paper describes the development of a CFD based design system to make heat transfer predictions. A 3-D, compressible, Reynolds-averaged Navier-Stokes CFD solver with k-ω turbulence modeling was used. A wall integration approach was used for boundary layer prediction. First, the numerical approach was validated against a series of fundamental airfoil cases with available data. The comparisons were very favorable. Subsequently, it was applied to a real engine airfoil at typical design conditions. A discussion of the features of the airfoil heat transfer distribution is included.

scholarly journals Inclusion of Viscous Dissipation on the Boundary Layer Flow of Cu-TiO2 Hybrid Nanofluid over Stretching/Shrinking Sheet

2021 ◽  
Vol 88 (2) ◽  
pp. 64-79
Author(s):  
Yap Bing Kho ◽  
Rahimah Jusoh ◽  
Mohd Zuki Salleh ◽  
Muhammad Khairul Anuar Mohamed ◽  
Zulkhibri Ismail ◽  
...  
Keyword(s):  
Boundary Layer ◽  
Differential Equations ◽  
Viscous Dissipation ◽  
Boundary Layer Flow ◽  
Skin Friction Coefficient ◽  
Shrinking Sheet ◽  
Hybrid Nanofluid ◽  
Suction Parameter ◽  
Similarity Transformations ◽  
Layer Flow

The effects of viscous dissipation on the boundary layer flow of hybrid nanofluids have been investigated. This study presents the mathematical modelling of steady two dimensional boundary layer flow of Cu-TiO2 hybrid nanofluid. In this research, the surface of the model is stretched and shrunk at the specific values of stretching/shrinking parameter. The governing partial differential equations of the hybrid nanofluid are reduced to the ordinary differential equations with the employment of the appropriate similarity transformations. Then, Matlab software is used to generate the numerical and graphical results by implementing the bvp4c function. Subsequently, dual solutions are acquired through the exact guessing values. It is observed that the second solution adhere to less stableness than first solution after performing the stability analysis test. The existence of viscous dissipation in this model is dramatically brought down the rate of heat transfer. Besides, the effects of the suction and nanoparticles concentration also have been highlighted. An increment in the suction parameter enhances the magnitude of the reduced skin friction coefficient while the augmentation of concentration of copper and titanium oxide nanoparticles show different modes.

Sign in / Sign up

Export Citation Format

Share Document