scholarly journals Study on the Seismic Performance of Prefabricated Single-Segment Steel Jacket Bridge Piers

Symmetry ◽  
2021 ◽  
Vol 13 (12) ◽  
pp. 2312
Author(s):  
Baodong Deng ◽  
Yanmin Jia ◽  
Dongwei Liang
Keyword(s):  
Seismic Performance ◽  
Shaking Table ◽  
Parameter Analysis ◽  
Dynamic Responses ◽  
Bridge Piers ◽  
Longitudinal Reinforcement ◽  
Anchorage Length ◽  
Single Segment ◽  
Steel Jacket ◽  
Bridge Models

To study the seismic performance of prefabricated single-segment steel jacket piers connected by grouting sleeves, two scaled symmetrical pier models with different anchorage lengths of the longitudinal reinforcement in the grouting sleeves and a comparative symmetrical cast-in-place (CIP) model were designed. OpenSees finite element models were established and shaking table tests were carried out on the three scaled pier models. The seismic response of each pier was compared and analyzed. Results showed the stiffness of the two prefabricated piers was greater than that of the CIP pier, and other seismic responses were less than those of the CIP piers, The dynamic responses of the two prefabricated bridge models were similar and changing the anchorage length of the reinforcement in the grouting sleeve had little effect on the seismic performance of the prefabricated pier. The simulation results were in good agreement with the experimental results. In the parameter analysis, the counterweight of the pier top had the greatest influence on the seismic performance of the prefabricated pier. The anchorage length of the longitudinal reinforcement in the grouting sleeve could be 6–14 times the diameter of the longitudinal reinforcement. Moreover, the seismic performance was found to be optimal when the thickness of the steel jacket was 5–7 mm.

scholarly journals Seismic Performance of Deposit Slopes With Underlying Bedrock Before and After Reinforcement by Stabilising Piles

2021 ◽  
Author(s):  
Zhiliang Sun ◽  
Kong Lingwei ◽  
Bai Wei ◽  
Wang Yong
Keyword(s):  
Seismic Performance ◽  
Seismic Waves ◽  
Bending Moment ◽  
Resultant Force ◽  
Shaking Table ◽  
Slope Instability ◽  
Dynamic Responses ◽  
Seismic Excitation ◽  
Ground Acceleration ◽  
Response Characteristics

Abstract The seismic performance of stabilising piles used to reinforce underlying bedrock in a deposit slope is a complex soil-structure interaction problem, on which there is limited design guidance on the optimum use of a single row of rock-socketed piles to reinforce such slopes. Two centrifuge shaking-table model tests at a geometric scale of 1:50 were conducted to ascertain the dynamic responses of the underlying bedrock deposit slopes without and with the use of stabilising piles during an earthquake. Multi-stage seismic waves with various peak accelerations were applied from the bottom of each model. Under seismic excitation, the differences in the response accelerations between the deposit and bedrock increase significantly with the increase in amplitude of the input seismic waves. The two are prone to uncoordinated movement, which leads to slope instability. Setting stabilising piles reduces the crest settlement and angular deformation and changes the natural frequency of the slope crest. The presence of the rock-socketed stabilising piles can bridge the uncoordinated movement of the bedrock and the overlying deposit to some extent. According to the mobilised pile bending moment, shear force, lateral pile-soil load distribution, and pile displacement, the dynamic response characteristics of stabilising piles under continuous multi-level seismic excitation were analysed. The resultant force arising from a distributed load increment on the piles caused by an earthquake is mainly concentrated in the upper part (the point of action of the resultant force is 1.54m below the slope surface). With increases in the peak ground acceleration (PGA) of the input motion, the resistance of the bedrock in front of the stabilising piles increases; moreover, with the increase of PGA, the peak resistance under the bedrock surface of the stabilising piles gradually moves downwards. This finding indicates that the strong seismic motion significantly changes the embedded working state of the stabilising pile.

scholarly journals Experimental Study on Seismic Performance of Prefabricated Utility Tunnel

2019 ◽  
Vol 2019 ◽  
pp. 1-14
Author(s):  
Xu Duan ◽  
Qi Dong ◽  
Wanjun Ye
Keyword(s):  
Seismic Performance ◽  
Boundary Effect ◽  
Public Utility ◽  
Shaking Table ◽  
Dynamic Responses ◽  
Dynamic Strain ◽  
Soil Pressure ◽  
Scaled Model ◽  
Sensor Arrangement ◽  
Utility Tunnel

Utility tunnel is a kind of underground tunnel structure that carries more than two types of public utility lines, and the utility tunnels built by the prefabricated method have been adopted in many modern cities due to their easy maintenance and environmental protection capabilities. However, knowledge about the seismic performance of the prefabricated utility tunnel and pipelines inside is quite limited. In this paper, a prefabricated utility tunnel newly built in Xi’an, China, is taken as the prototype; a series of shaking table tests are conducted to investigate the seismic performance of the prefabricated utility tunnel in loess foundation, using El Centro earthquake wave as the input loading. Details of the experimental setup focus on the design of the soil container, scaled model (1 : 10), sensor arrangement, and test cases. Dynamic responses including evaluation of boundary effect, the amplification factor of the ground and structure, distribution of soil pressure, characteristics of predominant frequencies, and the damage phenomena are analyzed. Dynamic strain obtained by Fiber Bragg Grating sensors releases the critical positions of the prefabricated utility tunnel during the earthquake. Moreover, the dynamic responses of the pipelines contained in the utility tunnel are also analyzed. From aforementioned results, the seismic performance of the prefabricated utility tunnel has been revealed. The results will provide a reference for the seismic design of prefabricated utility tunnels.

scholarly journals Seismic Performance of Ni-Ti SMA Wires Equipped in the Spatial Skeletal Structure

2021 ◽  
Vol 8 ◽  
Author(s):  
Yang Liu ◽  
Tao Yang ◽  
Binbin Li ◽  
Bo Liu ◽  
Wentao Wang ◽  
...  
Keyword(s):  
Numerical Model ◽  
Vibration Control ◽  
Seismic Performance ◽  
Passive Control ◽  
Shaking Table Test ◽  
Experimental Tests ◽  
Shaking Table ◽  
Dynamic Responses ◽  
Skeletal Structure ◽  
Performance Study

Nickel Titanium (Ni-Ti) Shape Memory Alloy (SMA) can be used to limit response of structure during external disturbances such as large seismic events. This paper presents a seismic performance study of Ni-Ti SMA wires equipped in the spatial skeletal structure. First, an improved Graesser-Cozzarelli (G-C) numerical constitutive model of the Austenitic phase of NiTi SMA wire is established. By contrast, the model based on uniaxial cyclic loading experimental tests is demonstrated as feasibility and validity. Next, a method consisting of a three-layer steel spatial skeletal structure model equipped with SMA wires is employed for simulation and experimental tests. According to the obtained constitutive numerical model, the simulation program of vibration control is written to simulate the effect of vibration control of seismic EL-centro wave. Furthermore, a shaking table experimental test was designed to verify the vibration control effect under the same action of seismic EL-centro wave. By comparison of the results of the numerical simulation and shaking table test, dynamic responses of the displacement and acceleration for different floors with control and without control was concluded. The superior superelastic properties of SMA wires used in passive control are investigated and the correctness of the constitutive numerical model are verified as well. The results show that such a comprehensive analysis integrates seismic-resistant behavior of Ni-Ti SMA wires in this type of structure. Besides, proposed method has broad application prospects to address the issues in passive control field of building structures.

scholarly journals Seismic Performance of Deposit Slopes with Underlying Bedrock before and after Reinforcement by Stabilizing Piles

2021 ◽  
Vol 11 (12) ◽  
pp. 5664
Author(s):  
Zhiliang Sun ◽  
Lingwei Kong ◽  
Wei Bai ◽  
Yong Wang
Keyword(s):  
Seismic Performance ◽  
Seismic Waves ◽  
Shaking Table ◽  
Dynamic Responses ◽  
Ground Acceleration ◽  
Stabilizing Piles ◽  
Multi Stage ◽  
Before And After ◽  
Table Model ◽  
Input Motion

The seismic performance of stabilizing piles used to reinforce underlying bedrock in a deposit slope is a complex soil–structure interaction problem. Two centrifuge shaking table model testswere conducted to ascertain the dynamic responses of the underlying bedrock deposit slopes without and with the use of stabilizing piles during an earthquake. Multi-stage seismic waves with various peak accelerations were applied from the bottom of each model. The differencesin the response accelerations between the deposit and bedrock increase significantly with the increase in amplitude of the input seismic waves. The presence of the rock-socketed stabilizing piles can bridge the uncoordinated movement of the bedrock and the overlying deposit to some extent. The resultant force arising from a distributed load increment on the piles caused by an earthquake is mainly concentrated in the upper part. With increases in the peak ground acceleration of the input motion, the resistance of the bedrock in front of the stabilizing piles increases and the peak resistance under the bedrock surface of the stabilizing piles gradually moves downwards.This finding indicates that the strong seismic motion significantly changes the embedded working state of the stabilizing pile.

scholarly journals Experimental Study on the Behavior of Existing Reinforced Concrete Multi-Column Piers under Earthquake Loading

2021 ◽  
Vol 11 (6) ◽  
pp. 2652
Author(s):  
Jung Han Kim ◽  
Ick-Hyun Kim ◽  
Jin Ho Lee
Keyword(s):  
Seismic Performance ◽  
Seismic Design ◽  
Bridge Piers ◽  
Scale Model ◽  
Inertia Force ◽  
Small Scale ◽  
Lap Splice ◽  
Existing Structures ◽  
Seismic Design Code ◽  
Seismic Force

When a seismic force acts on bridges, the pier can be damaged by the horizontal inertia force of the superstructure. To prevent this failure, criteria for seismic reinforcement details have been developed in many design codes. However, in moderate seismicity regions, many existing bridges were constructed without considering seismic detail because the detailed seismic design code was only applied recently. These existing structures should be retrofitted by evaluating their seismic performance. Even if the seismic design criteria are not applied, it cannot be concluded that the structure does not have adequate seismic performance. In particular, the performance of a lap-spliced reinforcement bar at a construction joint applied by past practices cannot be easily evaluated analytically. Therefore, experimental tests on the bridge piers considering a non-seismic detail of existing structures need to be performed to evaluate the seismic performance. For this reason, six small scale specimens according to existing bridge piers were constructed and seismic performances were evaluated experimentally. The three types of reinforcement detail were adjusted, including a lap-splice for construction joints. Quasi-static loading tests were performed for three types of scale model with two-column piers in both the longitudinal and transverse directions. From the test results, the effect on the failure mechanism of the lap-splice and transverse reinforcement ratio were investigated. The difference in failure characteristics according to the loading direction was investigated by the location of plastic hinges. Finally, the seismic capacity related to the displacement ductility factor and the absorbed energy by hysteresis behavior for each test were obtained and discussed.

Sign in / Sign up

Export Citation Format

Share Document