scholarly journals INCREASING OF THERMAL FIRE RESISTANCE OF COTTON THREADS

2020 ◽  
pp. 99-102
Author(s):  
N. A. Keibal ◽  
V. F. Kablov ◽  
D. S. Shipovskaya ◽  
L. K. Buneeva
Keyword(s):  
Aqueous Solution ◽  
Polyvinyl Alcohol ◽  
Water Absorption ◽  
Fire Resistance ◽  
High Efficiency ◽  
Fire Retardant ◽  
Single Stage ◽  
Cotton Threads

The results of studies of fire - resistant impregnating compositions based on an aqueous solution of polyvinyl alcohol and an antipyretic additive-methylphosphite borate are presented. The effectiveness of single-stage processing of cotton threads with these impregnating compositions has been proved. It is established that the developed impregnating compositions for cotton threads have shown high efficiency of thermal and fire-retardant action. The influence of the developed impregnation formulations on water absorption and strength of cotton threads was evaluated.

Improvement of Ti/RuO2–IrO2 Anode Lifetime and Electrocatalytical Properties by Using an Eco-Friendly Thermal Decomposition Method Using Polyvinyl Alcohol as Solvent

2019 ◽  
Author(s):  
Charlys Bezerra ◽  
Géssica Santos ◽  
Marilia Pupo ◽  
Maria Gomes ◽  
Ronaldo Silva ◽  
...  
Keyword(s):  
Thermal Decomposition ◽  
Polyvinyl Alcohol ◽  
High Efficiency ◽  
Electrochemical Impedance ◽  
Pechini Method ◽  
Low Cost ◽  
Charge Transfer Resistance ◽  
Transfer Resistance ◽  
Calcination Temperatures ◽  
Service Lifetime

<p>Electrochemical oxidation processes are promising solutions for wastewater treatment due to their high efficiency, easy control and versatility. Mixed metal oxides (MMO) anodes are particularly attractive due to their low cost and specific catalytic properties. Here, we propose an innovative thermal decomposition methodology using <a>polyvinyl alcohol (PVA)</a> as a solvent to prepare Ti/RuO<sub>2</sub>–IrO<sub>2</sub> anodes. Comparative anodes were prepared by conventional method employing a polymeric precursor solvent (Pechini method). The calcination temperatures studied were 300, 400 and 500 °C. The physical characterisation of all materials was performed by X-ray diffraction and scanning electron microscopy coupled with energy dispersive spectroscopy, while electrochemical characterisation was done by cyclic voltammetry, accelerated service lifetime and electrochemical impedance spectroscopy. Both RuO<sub>2</sub> and IrO<sub>2</sub> have rutile-type structures for all anodes. Rougher and more compact surfaces are formed for the anodes prepared using PVA. Amongst temperatures studied, 300 °C using PVA as solvent is the most suitable one to produce anodes with expressive increase in voltammetric charge (250%) and accelerated service lifetime (4.3 times longer) besides reducing charge-transfer resistance (8 times lower). Moreover, the electrocatalytic activity of the anodes synthesised with PVA toward the Reactive Blue 21 dye removal in chloride medium (100 % in 30 min) is higher than that prepared by Pechini method (60 min). Additionally, the removal total organic carbon point out improved mineralisation potential of PVA anodes. Finally, this study reports a novel methodology using PVA as solvent to synthesise Ti/RuO<sub>2</sub>–IrO<sub>2</sub> anodes with improved properties that can be further extended to synthesise other MMO compositions.</p>

REMOVAL OF HEAVY METAL Cr (II), Ni (II), Cu (II), Zn (II), Cd (II), Pb (II) IONS FROM AQUEOUS SOLUTION BY MENTHA PIPERITA EXTRACT

2020 ◽  
pp. 15-20
Author(s):  
Ersin Yucel ◽  
Mine Yucel
Keyword(s):  
Aqueous Solution ◽  
Metal Ions ◽  
High Efficiency ◽  
Correlation Coefficients ◽  
Langmuir Model ◽  
Mentha Piperita ◽  
Freundlich Model ◽  
Biosorption Capacity ◽  
Peppermint Extract ◽  
The Stability

In this study, the usage of the peppermint (Mentha piperita) for extracting the metal ions [Mg (II), Cr (II), Ni (II), Cu (II), Zn (II), Cd (II), Pb (II)] that exist at water was investigated. In order to analyze the stability properties, Langmuir, Freundlich, Temkin and Dubinin-Radushkevich isotherms were used at removing the metal ions and the highest correlation coefficients (R2) were obtained at Langmuir isotherm. Therefore, it is seen that the Langmuir model is more proper than the Freundlich model. However, it was found that the correlation coefficients of removing Ni and Cd is higher at Freundlich model than Langmuir and low at Dubinin-Radushkevich isotherm. It is established that the biosorption amount increase depends on the increase of biosorbent and it can be achieved high efficiency (95%) even with small amount (0.6 mg, peppermint extract) at lead ions. It is also determined that the peppermint extracted that is used at this study shows high biosorption capacity for metal ions and can be used for immobilization of metals from polluted areas.

scholarly journals Experimental Study on Delaying the Failure Time of In-Service Cables in Trays by Using Fire-Retardant Coatings

2021 ◽  
Vol 11 (6) ◽  
pp. 2521
Author(s):  
Feng Jiang ◽  
Jianyong Liu ◽  
Wei Yuan ◽  
Jianbo Yan ◽  
Lin Wang ◽  
...  
Keyword(s):  
Fire Resistance ◽  
Failure Time ◽  
Fire Retardant ◽  
Resistance Test ◽  
Control Group ◽  
Engineering Practice ◽  
Standard Fire ◽  
Oil Storage ◽  
Fire Resistance Test ◽  
Test Furnace

Improving the fire resistance of the key cables connected to firefighting and safety equipment is of great importance. Based on the engineering practice of an oil storage company, this study proposes a modification scheme that entails spraying fire-retardant coatings on the outer surface of a cable tray to delay the failure times of the cables in the tray. To verify the effect, 12 specimens were processed using five kinds of fire-retardant coatings and two kinds of fire-resistant cotton to coat the cable tray. The specimens were installed in the vertical fire resistance test furnace. For the ISO 834 standard fire condition, a fire resistance test was carried out on the specimens. The data for the surface temperature and the insulation resistance of the cables in trays were collected, and the fireproof effect was analyzed. The results showed that compared with the control group, the failure time of the cable could be delayed by 1.57–14.86 times, and the thicker the fire-retardant coatings were, the better the fireproof effect was. In general, the fire protection effect of the fire-retardant coating was better than that of the fire-resistant cotton.

scholarly journals High efficiency removal of Pb(ii) in aqueous solution by a biochar-supported nanoscale ferrous sulfide composite

RSC Advances ◽  
2021 ◽  
Vol 11 (2) ◽  
pp. 953-959
Author(s):  
Chengguang Chen ◽  
Muqing Qiu
Keyword(s):  
Aqueous Solution ◽  
High Efficiency ◽  
Ferrous Sulfide

A biochar-supported nanoscale ferrous sulfide composite was prepared and applied for the treatment of Pb(ii) ions in aqueous solution.

High Efficiency Combined Aggregate – Submerged Combustion Melter–Electric Furnace for Vitrification of High-Level Radioactive Wastes

2004 ◽  
Author(s):  
L. S. Pioro ◽  
I. L. Pioro
Keyword(s):  
Electric Furnace ◽  
High Efficiency ◽  
High Capacity ◽  
Main Idea ◽  
Melting Process ◽  
Radioactive Wastes ◽  
Single Stage ◽  
Interface Surface ◽  
High Level ◽  
Submerged Combustion

It is well known that high-level radioactive wastes (HLRAW) are usually vitrified inside electric furnaces. Disadvantages of electric furnaces are their low melting capacity and restrictions on charge preparation. Therefore, a new concept for a high efficiency combined aggregate – submerged combustion melter (SCM)–electric furnace was developed for vitrification of HLRAW. The main idea of this concept is to use the SCM as the primary high-capacity melting unit with direct melt drainage into an electric furnace. The SCM employs a single-stage method for vitrification of HLRAW. The method includes concentration (evaporation), calcination, and vitrification of HLRAW in a single-stage process inside a melting chamber of the SCM. Specific to the melting process is the use of a gas-air or gas-oxygen-air mixture with direct combustion inside a melt. Located inside the melt are high-temperature zones with increased reactivity of the gas phase, the existence of a developed interface surface, and intensive mixing, leading to intensification of the charge melting and vitrification process. The electric furnace clarifies molten glass, thus preparing the high-quality melt for subsequent melt pouring into containers for final storage.

Sign in / Sign up

Export Citation Format

Share Document