scholarly journals Performance in Binary Characteristics of Sisal Fibre Reinforced Concrete

2019 ◽  
Vol 9 (1) ◽  
pp. 44-47
Keyword(s):  
Compressive Strength ◽  
Reinforced Concrete ◽  
Fly Ash ◽  
Flexural Strength ◽  
Chloride Ions ◽  
Fiber Reinforced Concrete ◽  
Test Method ◽  
Sisal Fiber ◽  
Durability Test ◽  
Sisal Fibre

This research study has experimentally performed on the compressive strength, split tensile flexural strength and durability test method also emphasized in various mixes of high-performance concrete. The maximum compressive strength of concrete was noted for different curing days, while the addition of fly ash 20% with 15% of slag along with1% of sisal fiber reinforced concrete than compared to Plain Portland cement content up to 100%. Further, increasing the cementitious binder content there is a drastic fall in strength gain was observed than that of other mixes. On the contrary, the best mix was identified that's 10% fly ash along with 15% of slag produced the highest compressive strength, split tensile strength and flexural strength for different days of cured the concrete specimens. Also, the durability test performed as prescribed in ATMC 1202, based on the lab test results, it is concluded that the electrical charge passed over all the concrete specimen at 28 and 56 days presents the lesser values 1000 (coulombs) this is the evidently proved that the high resistance towards the corrosions and drastically reduced the chloride ions permeability except for plain cement concrete.

scholarly journals Influence Factors on the Properties of Ultrahigh-Performance Fiber-Reinforced Concrete Cured under the Condition of Room Temperature

2018 ◽  
Vol 2018 ◽  
pp. 1-9
Author(s):  
Pu Zhang ◽  
Yiliang Huang ◽  
Yongqi Li ◽  
Jun Zhao ◽  
Hengqian Dong ◽  
...  
Keyword(s):  
Compressive Strength ◽  
Reinforced Concrete ◽  
Fly Ash ◽  
Influence Factors ◽  
Volume Ratio ◽  
Fiber Reinforced Concrete ◽  
Fiber Reinforced ◽  
Curing Conditions ◽  
Heat Curing ◽  
Composition Materials

Ultrahigh-performance fiber-reinforced concrete (UHPFRC) is a new type of concrete with excellent performance and good application prospects. However, expensive heat curing or high-pressure curing was often adopted to ensure the sufficient compressive strength. This study focuses on improving the compressive strength and workability of UHPFRC by changing the composition materials and the mixture ratios under standard curing conditions. The 0-1 mm and 1∼3 mm sintered bauxite was adopted as coarse aggregate. UHPFRC with high compressive strength and good workability was developed by changing the water-binder ratios, by adding ground-granulated blast furnace slag (GGBFS) or fly ash, and by changing the bauxite content of different particle sizes. When the volume ratio of steel fiber was 3%, the recommend water to binder ratio was 0.194 according to this experiment, the dosage of GGBFS-replaced cement is recommended as 20%, the dosage of fly ash instead of silica fume is recommended as 30%. The recommend ratio of 0-1 mm and 1∼3 mm sintered bauxite was 1.51 : 1. Finally, a kind of UHPFRC material with a compressive strength of 152.4 MPa and a slump of 120 mm was developed under the standard curing conditions.

Polypropylene Fiber Reinforced Concrete for Airport Rigid Pavements: Compressive and Flexural Strength

2011 ◽  
Vol 219-220 ◽  
pp. 1601-1607 ◽  
Author(s):  
Tammam Merhej ◽  
Xin Kai Li ◽  
De Cheng Feng
Keyword(s):  
Compressive Strength ◽  
Reinforced Concrete ◽  
Flexural Strength ◽  
Volume Fraction ◽  
Linear Regression Analysis ◽  
Polypropylene Fiber ◽  
Fiber Reinforced Concrete ◽  
Fiber Reinforced ◽  
Rigid Pavements ◽  
Polypropylene Fiber Reinforced Concrete

This paper presents the experimental investigation carried out to study the behavior of polypropylene fiber reinforced concrete (PPFRC) under compression and flexure. Crimped polypropylene fibers and twisted polypropylene fiber were used with 0.0%, 0.2%, 0.4% and 0.6% volume fractions. The influence of the volume fraction of each shape of polypropylene fiber on the compressive strength and flexural strength is presented. Empirical equations to predict the effect of polypropylene fiber on compressive and flexural strength of concrete were proposed using linear regression analysis. An increase of 27% in flexural strength was obtained when 0.6% volume fraction of twisted polypropylene fiber was added. It was also found that the contribution of fiber in flexural strength is more effective when twisted fibers were used. The compressive strength was found to be less affected by polypropylene fiber addition.

scholarly journals An analysis of fresh, mechanical and durability properties of lightweight self-consolidating fiber reinforced concrete

2021 ◽  
Author(s):  
Imge Nicole Celasun
Keyword(s):  
Compressive Strength ◽  
Reinforced Concrete ◽  
Flexural Strength ◽  
Chloride Ion ◽  
Crumb Rubber ◽  
Fiber Content ◽  
Fiber Reinforced Concrete ◽  
Fiber Reinforced ◽  
Acid Attack ◽  
Chloride Permeability

This research investigated the fresh, mechanical and durability behavior of lightweight self-consolidating fiber reinforced concrete (LWSCFRC) with four different fibers (Polyethylene, Polyvinyl Alcohol, High-Density Polyethylene and Crumb Rubber). Two LWSCFRC mixtures were created for each fiber to analyze the effects of increasing fiber content on fresh state properties: slump flow and density. Mechanical and durability tests included compressive/ flexural strength, rapid chloride permeability and resistance to acid attack. The increase in fiber content decreased the workability of LWSCFRC mixtures except for crumb rubber. Flexural strength of all LWSCFRC specimens was similar compared to their control counterparts, while crumb rubber exhibited the highest compressive strength from all fiber specimens. Addition of fibers resulted in good resistance against chloride ion penetration but compressive strength of specimens in a 5% sulfuric acid solution decreased. Overall, 1.0% Crumb Rubber performed better in fresh, mechanical and durability testing from all the fiber specimens.

scholarly journals Impact of Length and Percent Dosage of Recycled Steel Fibers on the Mechanical Properties of Concrete

2021 ◽  
Vol 7 (10) ◽  
pp. 1650-1666
Author(s):  
Akhtar Gul ◽  
Bashir Alam ◽  
Muhammad Junaid Iqbal ◽  
Wisal Ahmed ◽  
Khan Shahzada ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Reinforced Concrete ◽  
Fiber Reinforced Concrete ◽  
Modulus Of Rupture ◽  
Test Results ◽  
Durability Test ◽  
Waste Tyres ◽  
Ultimate Load Carrying Capacity ◽  
Recycled Steel

The global rapid increase in waste tyres accumulation, as well as the looming social and environmental concerns, have become major threats in recent times. The use of Recycled Steel Fiber (RSF) extracted from waste tyres in fiber reinforced concrete can be of great profitable engineering applications however the choice of suitable length and volume fractions of RSF is presently the key challenge that requires research exploration. The present experimental work aims at investigating the influence of varying lengths (7.62 and 10.16 cm) and dosages (1, 1.5, 2, 2.5, 3, 3.5, and 4%) of RSF on the various mechanical properties and durability of concrete. Test results revealed that the varying lengths and dosages of RSF significantly affect the mechanical properties of concrete. The improvements in the compressive strength, splitting tensile strength, and Modulus of Rupture (MOR) of RSF reinforced concrete observed were about 26, 70, and 63%, respectively. Moreover, the RSF reinforced concrete showed an increase of about 20 and 15% in the yield load and ultimate load-carrying capacity, respectively. The durability test results showed a greater loss in compressive strength and modulus of elasticity and a smaller loss in concrete mass of SFRC. Based on the experimental findings of this study, the optimum dosages of RSF as 2.5 and 2% for the lengths 7.62 and 10.16 cm lengths, respectively are recommended for production of structural concrete. Doi: 10.28991/cej-2021-03091750 Full Text: PDF

scholarly journals An analysis of fresh, mechanical and durability properties of lightweight self-consolidating fiber reinforced concrete

2021 ◽  
Author(s):  
Imge Nicole Celasun
Keyword(s):  
Compressive Strength ◽  
Reinforced Concrete ◽  
Flexural Strength ◽  
Chloride Ion ◽  
Crumb Rubber ◽  
Fiber Content ◽  
Fiber Reinforced Concrete ◽  
Fiber Reinforced ◽  
Acid Attack ◽  
Chloride Permeability

This research investigated the fresh, mechanical and durability behavior of lightweight self-consolidating fiber reinforced concrete (LWSCFRC) with four different fibers (Polyethylene, Polyvinyl Alcohol, High-Density Polyethylene and Crumb Rubber). Two LWSCFRC mixtures were created for each fiber to analyze the effects of increasing fiber content on fresh state properties: slump flow and density. Mechanical and durability tests included compressive/ flexural strength, rapid chloride permeability and resistance to acid attack. The increase in fiber content decreased the workability of LWSCFRC mixtures except for crumb rubber. Flexural strength of all LWSCFRC specimens was similar compared to their control counterparts, while crumb rubber exhibited the highest compressive strength from all fiber specimens. Addition of fibers resulted in good resistance against chloride ion penetration but compressive strength of specimens in a 5% sulfuric acid solution decreased. Overall, 1.0% Crumb Rubber performed better in fresh, mechanical and durability testing from all the fiber specimens.

Mechanical properties of black sugar palm fiber-reinforced concrete

2011 ◽  
Vol 30 (11) ◽  
pp. 994-1004 ◽  
Author(s):  
T. Ferdiansyah ◽  
H. Abdul Razak
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Reinforced Concrete ◽  
Flexural Strength ◽  
Volume Fraction ◽  
Crack Deflection ◽  
Fiber Reinforced Concrete ◽  
Engineering Properties ◽  
Palm Fiber ◽  
Sugar Palm Fiber

This article reports the results of an investigation on the engineering properties of concrete containing black sugar palm fiber. Three fiber lengths of 15, 25, and 35 mm in four volume fractions, namely 0.2%, 0.4%, 0.6%, and 0.8%, were utilized in this investigation. The values of compressive, flexural, toughness, first crack deflection, first crack toughness, and toughness indices are reported for ages up to 90 days. It was observed that the addition of palm fibers slightly increased the flexural strength of concrete. The incorporation of the fibers had no significant effect on the compressive strength. The mix with 0.8% volume fraction and 35 mm length fiber gave higher toughness and ductility compared to other mixes.

Experimental Study of the Mechanical Properties of Hybrid Fiber Reinforced Concrete

2009 ◽  
Vol 610-613 ◽  
pp. 69-75
Author(s):  
Yuan Hua ◽  
Tai Quan Zhou
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Reinforced Concrete ◽  
Aspect Ratio ◽  
Flexural Strength ◽  
Fiber Reinforced Concrete ◽  
Fiber Reinforced ◽  
Hybrid Fiber ◽  
Reinforced Fiber ◽  
Reinforced Materials

Different kinds of fiber are used to reinforce the concrete to improve the concrete mechanical properties. The high modulus and high flexibility fibers are often used to reinforce in the cement base, which leads to the higher performance compound cement based materials. In the paper, the carbon fiber and glass fiber material are used as flexibility reinforced materials. The polypropylene fiber and the polyethylene fiber are used as strength reinforced materials. The combinations of the flexibility reinforced fiber and strength reinforced fiber are chosen as C-P HF (Carbon and Polypropylene Hybrid Fiber) and G-Pe HF (Glass and Polyethylene Hybrid Fiber). The concrete mixture ratio and the fiber-reinforced amount are determined to the author’s previous study. The relationship between compressive strength, flexural strength and length/diameter aspect ratio of fiber for the carbon and polypropylene hybrid fiber reinforced concrete (C-P HFRC), and for the glass and polyethylene hybrid fiber reinforced concrete (G--Pe HFRC) was tested and discussed. The testing results show that length/diameter aspect ratio of fiber obviously affects the flexural strength of C-P HFRC and G-Pe HFRC, though the compressive strength is slightly affected by the length-diameter aspect ratio.

Mechanical Properties of Fiber Reinforced Concrete

2018 ◽  
Vol 875 ◽  
pp. 174-178
Author(s):  
Bhawat Chaichannawatik ◽  
Athasit Sirisonthi ◽  
Qudeer Hussain ◽  
Panuwat Joyklad
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Compressive Strength ◽  
Reinforced Concrete ◽  
Glass Fiber ◽  
Plain Concrete ◽  
Fiber Reinforced Concrete ◽  
Sisal Fiber ◽  
Fiber Reinforced ◽  
Glass Fiber Reinforced

This study presents results of an experimental investigation conducted to investigate the mechanical properties of sisal and glass fiber reinforced concrete. Four basic concrete mixes were considered: 1) Plain concrete (PC) containing ordinary natural aggregates without any fibers, 2) sisal fiber reinforced concrete (SFRC), 3) sisal and glass fiber reinforced concrete (SGFRC), 4, glass fiber reinforced concrete (GFRC). Investigated properties were compressive strength, splitting tensile strength, flexural tensile strength and workability. The results of fiber reinforced concrete mixes were compared with plain concrete to investigate the effect of fibers on the mechanical properties of fiber reinforced concrete. It was determined that addition of different kinds of fibers (natural and synthetic) is very useful to produce concrete. The addition of fibers was resulted into higher compressive strength, splitting and tensile strength. However, the workability of the fiber reinforced concrete was found lower than the plain concrete due to the addition of fibers in the concrete.

The Influence of Carbonization on the Performances of Fly Ash Geopolymeric Concrete

2015 ◽  
Vol 744-746 ◽  
pp. 1519-1526 ◽  
Author(s):  
Qi Huang ◽  
Xiao Shuang Shi ◽  
Qing Yuan Wang ◽  
Ling Tang
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Chemical Composition ◽  
Ph Value ◽  
Test Method ◽  
Portland Cement Concrete ◽  
Durability Test ◽  
Obvious Effect ◽  
Phenolphthalein Solution ◽  
Term Performance

Two mixtures were designed to manufacture ordinary Portland cement concrete (PCC) and alkali-activated fly ash geopolymeric concrete (FGC). The depth of carbonation at 3rd,7th,14th and 28th day were measured according to the carbonization test method in “Ordinary Concrete Long-term Performance and Durability Test Method Standard”(GB/T 50082-2009) by spotting with phenolphthalein solution. The changes of compressive strength of the specimens carbonized with different days were tested and compared, as well as the pH value of specimens’ surfaces. Furthermore, the changes in microstructure and chemical composition were observed through the scanning electronic microscope (SEM) and energy dispersive X-ray spectrometer (EDX), respectively. The results show that although the compressive strength of FGC decreased significantly at first, but there is no obvious effect of carbonization on compressive strength, pH value and chemical composition of FGC as carbonation going on. Moreover, the microstructure of FGC is more homogeneous and denser. It can be concluded that compared with PCC, carbonization resistance of FGC is much better.

Sign in / Sign up

Export Citation Format

Share Document