About the Role of Interfaces on the Fatigue Crack Propagation in Laminated Metallic Composites

The influence of gradients in hardness and elastic properties at interfaces of dissimilar materials in laminated metallic composites (LMCs) on fatigue crack propagation is investigated experimentally for three different LMC systems: Al/Al-LMCs with dissimilar yield stress and Al/Steel-LMCs as well as Al/Ti/Steel-LMCs with dissimilar yield stress and Young’s modulus, respectively. The damage tolerant fatigue behavior in Al/Al-LMCs with an alternating layer structure is enhanced significantly compared to constituent monolithic materials. The prevalent toughening mechanisms at the interfaces are identified by microscopical methods and synchrotron X-ray computed tomography. For the soft/hard transition, crack deflection mechanisms at the vicinity of the interface are observed, whereas crack bifurcation mechanisms can be seen for the hard/soft transition. The crack propagation in Al/Steel-LMCs was studied conducting in-situ scanning electron microscope (SEM) experiments in the respective low cycle fatigue (LCF) and high cycle fatigue (HCF) regimes of the laminate. The enhanced resistance against crack propagation in the LCF regime is attributed to the prevalent stress redistribution, crack deflection, and crack bridging mechanisms. The fatigue properties of different Al/Ti/Steel-LMC systems show the potential of LMCs in terms of an appropriate selection of constituents in combination with an optimized architecture. The results are also discussed under the aspect of tailored lightweight applications subjected to cyclic loading.

Beneficial effect of low BN additive on densification and mechanical properties of hot-pressed ZrB2–SiC composites

The incorporation of 1 wt% hexagonal BN (hBN) into ZrB2–30 vol% SiC could noticeably better the fracture toughness, hardness, and consolidation behavior of this composite. This research intended to scrutinize the effects of various amounts of hBN (0–5 wt%) on different characteristics of ZrB2–SiC materials. The hot-pressing method under 10 MPa at 1900 °C for 120 min was employed to sinter all designed specimens. Afterward, the as-sintered samples were characterized using X-ray diffractometry (XRD), field emission scanning electron microscopy (FESEM), energy-dispersive X-ray spectroscopy (EDS), and Vickers technique. The hBN addition up to 1 wt% improved relative density, leading to a near fully dense sample; however, the incorporation of 5 wt% of such an additive led to a composite containing more than 5% remaining porosity. The highest Vickers hardness of 23.8 GPa and fracture toughness of 5.7 MPa.m1/2 were secured for the sample introduced by only 1 wt% hBN. Ultimately, breaking large SiC grains, crack bridging, crack deflection, crack branching, and crack arresting were introduced as the chief toughening mechanisms in the ZrB2–SiC–hBN system.

A comparative study of nano-fillers to improve toughness and modulus of polymer-derived ceramics

Brittleness is a major limitation of polymer-derived ceramics (PDCs). Different concentrations of three nanofillers (carbon nanotubes, Si3N4 and Al2O3 nanoparticles) were evaluated to improve both toughness and modulus of a commercial polysilazane (PSZ) PDC. The PSZs were thermally cross-linked and pyrolyzed under isostatic pressure in nitrogen. A combination of mechanical, chemical, density, and microscopy characterizations was used to determine the effects of these fillers. Si3N4 and Al2O3 nanoparticles (that were found to be active fillers) were more effective than nanotubes and improved the elastic modulus, hardness, and fracture toughness (JIC) of the PDC by ~ 1.5 ×, ~ 3 ×, and ~ 2.5 ×, respectively. Nanotubes were also effective in maintaining the integrity of the samples during pyrolysis. The modulus and hardness of PDCs correlated positively with their apparent density; this can provide a fast way to assess future PDCs. The improvement in fracture toughness was attributed to crack deflection and bridging observed in the micro-indentation cracks in the modified PDCs. The specific toughness of the modified PDCs was 4 × higher than that of high-purity alumina, and its specific modulus reached that of commercially available technical ceramics. These PDCs can also easily take different shapes and therefore are of interest in protective armor, propulsion, thermal protection, device packaging and biomaterial systems.

Microstructure study of fractured polar bear hair for toughening, strengthening, stiffening designs via energy dissipation and crack deflection mechanisms in materials

Polar bear hair is known for its superior thermal insulation properties protecting from frigid water and freezing weather conditions. However, this microscopy study of polar bear hair is related to...