scholarly journals Nano Alumina Based High Strength Concrete

2020 ◽  
Vol 9 (4) ◽  
pp. 256-363
Keyword(s):  
Mechanical Properties ◽  
High Strength Concrete ◽  
High Strength ◽  
Pulse Velocity ◽  
Hardened Concrete ◽  
Normal Concrete ◽  
Conventional Concrete ◽  
Tem Analysis ◽  
Strength Concrete ◽  
Nano Alumina

Very recently, the world of nano technology has initiated to fabricate new materials owing to the demand for their use in enhancing the properties of different materials in general and, materials used in the construction industry in particular. In this study, the results of an exhaustive experimental analysis, on the use of nano alumina with cement powder to enhance the grade and strength of concrete has been undertaken. The influence of the nano alumina in concrete with different proportions has been studied to assess mechanical properties of concrete with reference to normal concrete. The test results indicate that the use of nano alumina in concrete has enhanced the mechanical properties of hardened concrete. This nano alumina based high strength concrete (HSC) has an enhanced compressive strength of 64.17 N/mm2 (MPa) after 28 days, which is a significant improvement over normal concrete. All the mixes having nano alumina in different proportions gave better results as compared to normal conventional concrete mix. The Rebound Hammer, Ultrasonic Pulse Velocity, SEM and TEM analysis further validate the above findings.

An Experiment Investigation on Physical and Mechanical Properties of High Strength Concrete with Suitable Admixture

2019 ◽  
Vol 972 ◽  
pp. 10-15
Author(s):  
B.C. Gayana ◽  
Mallikarjuna Shashanka ◽  
Avinash N. Rao ◽  
Karra Ram Chandar
Keyword(s):  
Mechanical Properties ◽  
High Strength Concrete ◽  
Construction Material ◽  
Physical And Mechanical Properties ◽  
High Strength ◽  
Steel Fibers ◽  
Partial Replacement ◽  
Hardened Concrete ◽  
Conventional Concrete ◽  
Strength Concrete

Concrete is an essential construction material. Even-though conventional concrete performs and satisfy the structures under normal conditions, a few special situations require very high compressive strength of concrete. An experimental investigation is done to develop high strength concrete with suitable admixtures and steel fibers. The properties of fresh and hardened concrete with alccofine as partial replacement for binder and poly-carboxylate ether (Glenium 8233) and steel fibers is investigated for the workability and mechanical properties i.e., compressive, splitting tensile and flexural strength of concrete. Based on the results, the strength increased with the addition of alccofine compared to the control mix. Hence, by optimum percentage of alccofine, high strength of concrete of 112 MPa can be obtained.

scholarly journals IMPACT OF USING STONE POWDER AND MINERAL ADMIXTURES IN HIGH STRENGTH CONCRETE

2020 ◽  
Vol 4 (5) ◽  
pp. 82-87
Author(s):  
Afzal Basha Syed ◽  
Jayarami Reddy B ◽  
Sashidhar C
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
High Strength Concrete ◽  
High Strength ◽  
Mineral Admixtures ◽  
Test Results ◽  
Concrete Technology ◽  
Split Tensile Strength ◽  
Conventional Concrete ◽  
Strength Concrete

In present era, high-strength concrete is progressively utilized in modern concrete technology and particularly in the construction of elevated structures. This examination has been directed to explore the properties of high-strength concrete that was delivered by using stone powder (SP) as an option of extent on sand after being processed. The aim of the research is to study the effect of replacement of sand with stone powder and substitution of cement with mineral admixtures (GGBS & Zeolite) on the mechanical properties of high strength concrete. The test results showed clear improvement in compression and split tensile nature of concrete by using stone powder and mineral admixtures together in concrete. The increment in the magnitude of compressive strength and split tensile strength are comparable with conventional concrete.

scholarly journals ASSESSMENT OF MECHANICAL PROPERTIES OF HIGH STRENGTH CONCRETE (HSC) AFTER EXPOSURE TO HIGH TEMPERATURE

2018 ◽  
Vol 24 (2) ◽  
pp. 138-144 ◽  
Author(s):  
Tomasz DRZYMAŁA ◽  
Wioletta JACKIEWICZ-REK ◽  
Jerzy GAŁAJ ◽  
Ritoldas ŠUKYS
Keyword(s):  
Mechanical Properties ◽  
High Temperature ◽  
High Strength Concrete ◽  
High Performance Concrete ◽  
High Strength ◽  
Hardened Concrete ◽  
Explosive Spalling ◽  
Polypropylene Fibres ◽  
Strength Concrete ◽  
Temperature Conditions

There has been a tendency to design ever slender building construction using high strength concrete in recent years. Application of HSC is also growing in tunnel construction. One of the most important challenges is to control explosive spalling of concrete and the method recommended by Eurocode 2 (EN 1992-1-2:2008/NA:2010P) is addition of polypropylene fibres to the mix. The purpose of the research described in this paper was to evaluate the changes of mechanical properties of HSC exposed to the effect of high temperature. The tests were carried out on three types of high strength concrete: air-entrained concrete, polypropylene fibre-reinforced concrete and reference concrete having constant water/cement ratio. The properties of hardened concrete including compressive strength, tensile splitting strength, flexural strength and E-modulus were studied. The latter tests were carried out on both on concrete cured at 20 °C and concrete subjected to high-temperature conditions at 300 °C, 450 °C and 600 °C. The results enabled us to evaluate the effect of high-temperature conditions on the properties of high-performance concrete and compare the effectiveness of the two methods designed to improve the high-temperature performance of the concrete: addition of polypropylene fibres and entrainment of air.

scholarly journals Recycled Aggregate Self-curing High-strength Concrete

2017 ◽  
Vol 3 (6) ◽  
pp. 427-441 ◽  
Author(s):  
Alaa Ali Bashandy ◽  
Noha M. Soliman ◽  
Mahmoud Hamdy Abd Elrahman
Keyword(s):  
High Strength Concrete ◽  
High Strength ◽  
Recycled Aggregate ◽  
Recycled Aggregates ◽  
Water Evaporation ◽  
Hardened Concrete ◽  
Curing Agent ◽  
Conventional Concrete ◽  
Strength Concrete ◽  
Concrete Properties

The use of recycled aggregates from demolished constructions as coarse aggregates for concrete becomes a need to reduce the negative effects on the environment. Internal curing is a technique that can be used to provide additional moisture in concrete for more effective hydration of cement to reduce the water evaporation from concrete, increase the water retention capacity of concrete compared to the conventionally cured concrete. High strength concrete as a special concrete type has a high strength with extra properties compared to conventional concrete. In this research, the combination of previous three concrete types to obtain self-curing high-strength concrete cast using coarse recycled aggregates is studied. The effect of varying water reducer admixture and curing agent dosages on both the fresh and hardened concrete properties is studied. The fresh properties are discussed in terms of slump values. The hardened concrete properties are discussed in terms of compressive, splitting tensile, flexure and bond strengths. The obtained results show that, the using of water reducer admixture enhances the main fresh and hardened properties of self-curing high-strength concrete cast using recycled aggregate. Also, using the suggested chemical curing agent increased the strength compared to conventional concrete without curing.

scholarly journals MECHANICAL PROPERTIES OF HIGH STRENGTH CONCRETE AT HIGH TEMPERATURES

2008 ◽  
Vol 73 (624) ◽  
pp. 341-347 ◽  
Author(s):  
Masashi MATSUDO ◽  
Hirokazu NISHIDA ◽  
Takahiro OHTSUKA ◽  
Takeo HIRASHIMA ◽  
Takeo ABE
Keyword(s):  
Mechanical Properties ◽  
High Temperatures ◽  
High Strength Concrete ◽  
High Strength ◽  
Strength Concrete

Comparison Analysis on the Mechanical Properties of HSC and NSC after the Action of High Temperatures

2014 ◽  
Vol 1014 ◽  
pp. 49-52
Author(s):  
Xiao Ping Su
Keyword(s):  
Mechanical Properties ◽  
High Temperature ◽  
High Temperatures ◽  
High Strength Concrete ◽  
Elasticity Modulus ◽  
Strain Curve ◽  
Peak Stress ◽  
High Strength ◽  
Peak Strain ◽  
Strength Concrete

With the wide application of high strength concrete in the building construction,the risk making concrete subject to high temperatures during a fire is increasing. Comparison tests on the mechanical properties of high strength concrete (HSC) and normal strength concrete (NSC) after the action of high temperature were made in this article, which were compared from the following aspects: the peak stress, the peak strain, elasticity modulus, and stress-strain curve after high temperature. Results show that the laws of the mechanical properties of HSC and NSC changing with the temperature are the same. With the increase of heating temperature, the peak stress and elasticity modulus decreases, while the peak strain grows rapidly. HSC shows greater brittleness and worse fire-resistant performance than NSC, and destroys suddenly. The research and evaluation on the fire-resistant performance of HSC should be strengthened during the structural design and construction on the HSC buildings.

Estimation of Compressive Strength of Recycled Aggregate High Strength Concrete Using Ultrasonic Pulse Velocity

2014 ◽  
Vol 605 ◽  
pp. 147-150
Author(s):  
Seong Uk Hong ◽  
Seung Hun Kim ◽  
Yong Taeg Lee
Keyword(s):  
Compressive Strength ◽  
High Strength Concrete ◽  
Coarse Aggregate ◽  
High Strength ◽  
Ultrasonic Pulse Velocity ◽  
Ultrasonic Pulse ◽  
Pulse Velocity ◽  
Recycled Aggregate ◽  
Strength Concrete ◽  
Recycled Coarse Aggregate

This study used the ultrasonic pulse velocity method, one of the non-destructive test methods that does not damage the building for maintenance of to-be-constructed concrete structures using recycled aggregates in order to estimate the compressive strength of high strength concrete structure using recycled coarse aggregate and provide elementary resources for technological establishment of ultrasonic pulse velocity method. 200 test pieces of high strength concrete 40, 50MPa using recycled coarse aggregate were manufactured by replacement rates (0, 30, 50, 100%) and age (1, 7, 28, 180days), and air curing was executed to measure compressive strength and wave velocity. As the result of compressive strength measurement, the one with age of 180day and design strength of 40MPa was 43.69MPa, recycled coarse aggregate replacement rate of 30% 50% 100% were 42.82, 41.22, 37.35MPa, and 50MPa was 52.50MPa, recycled coarse aggregate replacement rate of 30% 50% 100% were 49.02, 46.66, 45.30MPa, and while it could be seen that the test piece substituted with recycled aggregate was found to have lower strength than the test piece with natural aggregate only, but it still reached the design strength to a degree. The correlation of compressive strength and ultrasonic pulse velocity was found and regression analysis was conducted. The estimation formula for compressive strength of high strength concrete using recycled coarse aggregate was found to be Fc=0.069Vp4.05, R2=0.66

scholarly journals Effect of Locally Available Wheat Straw Ash in Developing High Strength Concrete

2021 ◽  
pp. 19-28
Author(s):  
Muhammad Armaghan Siffat ◽  
Muhammad Ishfaq ◽  
Afaq Ahmad ◽  
Khalil Ur Rehman ◽  
Fawad Ahmad
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Wheat Straw ◽  
High Strength Concrete ◽  
High Strength ◽  
Optimum Temperature ◽  
X Ray Diffraction ◽  
X Ray ◽  
Strength Concrete ◽  
Straw Ash

This study is supervised to assess the characteristics of the locally available wheat straw ash (WSA) to consume as a substitute to the cement and support in enhancing the mechanical properties of concrete. Initially, after incineration at optimum temperature of 800°C for 0.5, the ash of wheat straw was made up to the desirable level of fineness by passing through it to the several grinding cycles. Subsequently, the X-ray fluorescence (XRF) along with X-ray diffraction (XRD) testing conducted on ash of wheat straw for the evaluation its pozzolanic potential. Finally, the specimens of concrete were made by consuming 10% and 20% percentages of wheat straw ash as a replacement in concrete to conclude its impact on the compressive strength of high strength concrete. The cylinders of steel of dimensions 10cm diameter x 20cm depth were acquired to evaluate the compressive strength of high strength concrete. The relative outcomes of cylinders made of wheat straw ash substitution presented the slight increase in strength values of the concrete. Ultimately, the C-100 blends and WSA aided cement blends were inspected for the rheology of WSA through FTIR spectroscopy along with Thermogravimetric technique. The conclusions authenticate the WSA potential to replace cement in the manufacturing of the high strength concrete.

Sign in / Sign up

Export Citation Format

Share Document