scholarly journals Experimental of 4S Diesel Engine using Biofuel Blends with Enrichment of C2H2 Gas

2019 ◽  
Vol 8 (11) ◽  
pp. 1263-1267
Keyword(s):  
Diesel Engine ◽  
Fossil Fuel ◽  
Injection Pressure ◽  
Calorific Value ◽  
Waste Cooking Oil ◽  
Gas Temperature ◽  
Ic Engine ◽  
Auto Ignition ◽  
Exhaust Gas Temperature ◽  
Diesel Operation

In the present scenario owing to the depletion of fossil fuel and at the same time increase in demand averts the researchers towards the alternative fuel. Various investigation are being carried out to find the most suitable alternate for the fossil fuel in IC engine, which satisfies the demand, improves the performance and decreases the emission. This paper deals with the multi fuel mode. Tests were performed at 4S mono cylinder dual fuel diesel engine with blends of acetylene in different proportions (0.199 kg/hr., 0.394 kg/hr. and 0.588 kg/hr.) with 20% waste cooking oil at a rated injection pressure of 200bar.The result shows the increased in BTE and deceased BSFC and exhaust gas temperature, furtherance the decrease in NOx and CO are observed as the amount of acetylene increases. BTE increases due to the lower auto ignition temperature and high calorific value of acetylene. Graphs were obtained based on the performance of the engine and B20 with 0.394 kg/hr. of acetylene is concluded to be optimum, B20 with 0.199 kg/hr. of acetylene shows the result similar to diesel operation, at B20 with 0.588 kg/hr. of acetylene increase in the knocking effect was observed.

scholarly journals Find the Performance of Dual Fuel Engine Followed by Waste Cooking Oil Blends with Acetylene

2019 ◽  
Vol 9 (2) ◽  
pp. 127-131
Keyword(s):  
Fossil Fuel ◽  
Injection Pressure ◽  
Calorific Value ◽  
Waste Cooking Oil ◽  
Dual Fuel ◽  
Gas Temperature ◽  
Ic Engine ◽  
Oil Blends ◽  
Cooking Oil ◽  
Auto Ignition

In the present scenario owing to the depletion of fossil fuel and at the same time increase in demand averts the researchers towards the alternative fuel. Various investigation is being carried out to find the most suitable alternate for the fossil fuel in IC engine, which satisfies the demand, improves the performance and decreases the emission. This paper deals with the dual fuel mode. Tests were performed at single cylinder fore stroke dual fuel diesel engine with blends of acetylene in different proportions (0.199 kg/hr,0.394 kg/hr and 0.588 kg/hr) with 20% waste cooking oil at a rated injection pressure of 200bar.The result shows the increased in BTE and decreased BSFC and exhaust gas temperature, furtherance the decrease in NOx and CO are observed as the amount of acetylene increases. BTE increases because of lower auto ignition temperature and high calorific value of acetylene. Graphs were obtained based on the performance of the engine and B20 with 0.394 kg/hr of acetylene is concluded to be optimum, B20 with 0.199 kg/hr shows the result similar to diesel operation, at B20 with 0.588 kg/hr the increase in the knocking effect was observed.

scholarly journals Thermal Performance of Compression Ignition Engine Using High Content Biodiesels: A Comparative Study with Diesel Fuel

2021 ◽  
Vol 13 (14) ◽  
pp. 7688
Author(s):  
Asif Afzal ◽  
Manzoore Elahi M. Soudagar ◽  
Ali Belhocine ◽  
Mohammed Kareemullah ◽  
Nazia Hossain ◽  
...  
Keyword(s):  
Diesel Engine ◽  
Diesel Fuel ◽  
Fatty Acid Content ◽  
Engine Performance ◽  
Waste Cooking Oil ◽  
Gas Temperature ◽  
Compression Ignition Engine ◽  
Brake Thermal Efficiency ◽  
Acid Oil ◽  
Exhaust Gas Temperature

In this study, engine performance on thermal factors for different biodiesels has been studied and compared with diesel fuel. Biodiesels were produced from Pongamia pinnata (PP), Calophyllum inophyllum (CI), waste cooking oil (WCO), and acid oil. Depending on their free fatty acid content, they were subjected to the transesterification process to produce biodiesel. The main characterizations of density, calorific range, cloud, pour, flash and fire point followed by the viscosity of obtained biodiesels were conducted and compared with mineral diesel. The characterization results presented benefits near to standard diesel fuel. Then the proposed diesel engine was analyzed using four blends of higher concentrations of B50, B65, B80, and B100 to better substitute fuel for mineral diesel. For each blend, different biodiesels were compared, and the relative best performance of the biodiesel is concluded. This diesel engine was tested in terms of BSFC (brake-specific fuel consumption), BTE (brake thermal efficiency), and EGT (exhaust gas temperature) calculated with the obtained results. The B50 blend of acid oil provided the highest BTE compared to other biodiesels at all loads while B50 blend of WCO provided the lowest BSFC compared to other biodiesels, and B50 blends of all biodiesels provided a minimum % of the increase in EGT compared to diesel.

Engine Performance Investigations of Palm Oil, Jatropha Oil and Waste Cooking Oil as Alternative Fuel

2015 ◽  
Vol 1113 ◽  
pp. 674-678
Author(s):  
Syarifah Yunus ◽  
Noriah Yusoff ◽  
Muhammad Faiz Fikri Ahmad Khaidzir ◽  
Siti Khadijah Alias ◽  
Freddawati Rashiddy Wong ◽  
...  
Keyword(s):  
Palm Oil ◽  
Engine Performance ◽  
Alternative Fuel ◽  
Waste Cooking Oil ◽  
Biodiesel Production ◽  
Gas Temperature ◽  
Performance Effect ◽  
Cooking Oil ◽  
Exhaust Gas Temperature ◽  
Global Agenda

The continued using of petroleum energy as a sourced for fuel is widely recognized as unsustainable because of the decreasing of supplies while increasing of the demand. Therefore, it becomes a global agenda to develop a renewable, sustainable and alternative fuel to meets with all the demand. Thus, biodiesel seems to be one of the best choices. In Malaysia, the biodiesel used is from edible vegetable oil sources; palm oil. The uses of palm oil as biodiesel production source have been concern because of the competition with food materials. In this study, various types of biodiesel feedstock are being studied and compared with diesel. The purpose of this comparison is to obtain the optimum engine performance of these different types of biodiesel (edible, non-edible, waste cooking oil) on which are more suitable to be used as alternative fuel. The optimum engine performance effect can be obtains by considering the Brake Power (BP), Specific Fuel Consumption (SFC), Exhaust Gas Temperature (EGT) and Brake Thermal Efficiency (BTE).

Effect of Fuel Injection Strategy on DPF Regeneration in Single Cylinder Diesel Engine

2015 ◽  
Author(s):  
Sungjun Yoon ◽  
Hongsuk Kim ◽  
Daesik Kim ◽  
Sungwook Park
Keyword(s):  
Diesel Engine ◽  
Fuel Injection ◽  
Operating Conditions ◽  
Experimental Results ◽  
Exhaust Gas ◽  
Post Injection ◽  
Gas Temperature ◽  
Injection Strategy ◽  
Dpf Regeneration ◽  
Exhaust Gas Temperature

Stringent emission regulations (e.g., Euro-6) force automotive manufacturers to equip DPF (diesel particulate filter) on diesel cars. Generally, post injection is used as a method to regenerate DPF. However, it is known that post injection deteriorates specific fuel consumption and causes oil dilution for some operating conditions. Thus, an injection strategy for regeneration becomes one of key technologies for diesel powertrain equipped with a DPF. This paper presents correlations between fuel injection strategy and exhaust gas temperature for DPF regeneration. Experimental apparatus consists of a single cylinder diesel engine, a DC dynamometer, an emission test bench, and an engine control system. In the present study, post injection timing covers from 40 deg aTDC to 110 deg aTDC and double post injection was considered. In addition, effects of injection pressures were investigated. The engine load was varied from low-load to mid-load and fuel amount of post injection was increased up to 10mg/stk. Oil dilution during fuel injection and combustion processes were estimated by diesel loss measured by comparing two global equivalences ratios; one is measured from Lambda sensor installed at exhaust port, the other one is estimated from intake air mass and injected fuel mass. In the present study, the differences in global equivalence ratios were mainly caused from oil dilution during post injection. The experimental results of the present study suggest an optimal engine operating conditions including fuel injection strategy to get appropriate exhaust gas temperature for DPF regeneration. Experimental results of exhaust gas temperature distributions for various engine operating conditions were summarized. In addition, it was revealed that amounts of oil dilution were reduced by splitting post injection (i.e., double post injection). Effects of injection pressure on exhaust gas temperature were dependent on combustion phasing and injection strategies.

scholarly journals A model-based and experimental approach for the determination of suitable variable valve timings for cold start in partial load operation of a passenger car single-cylinder diesel engine

2018 ◽  
Vol 20 (1) ◽  
pp. 141-154 ◽  
Author(s):  
P Maniatis ◽  
U Wagner ◽  
T Koch
Keyword(s):  
Diesel Engine ◽  
Experimental Investigations ◽  
Exhaust Gas ◽  
Gas Temperature ◽  
Warm Up ◽  
One Dimensional ◽  
Engine Efficiency ◽  
Residual Gas ◽  
Dimensional Simulation ◽  
Exhaust Gas Temperature

A manipulation of the charge exchange allows controlling the amount of residual gas during engine warm-up. The residual gas during the warm-up phase leads to an increase of the exhaust gas temperature and supports to reach the exhaust after-treatment system operating temperature faster. In addition, the warm residual gas increases the combustion chamber temperature, which reduces the HC and CO emissions. However, fuel consumption increases. For that reason, such heating measures should be the best compromise of both, exhaust gas temperature increase and engine efficiency, in order to provide efficient heating strategies for passenger car diesel engines. Therefore, simulative and experimental investigations are carried out at the Institute of Internal Combustion Engines of the Karlsruhe Institute of Technology to establish a reliable cam design methodology. For the experimental investigations, a modern research single-cylinder diesel engine was set up on a test bench. In addition, a one-dimensional simulation model of the experimental setup was created in order to simulate characteristics of valve lift curves and to investigate their effects on the exhaust gas temperature and the exhaust gas enthalpy flow. These simulations were based on design of experiments (DoE), so that all characteristics can be used sustainably for modeling and explaining their influences on the engine operation. This methodology allows numerically investigating promising configurations and deriving cam contours which are manufactured for testing. To assess the potential of these individual configurations, the results obtained were compared with each other as well as with the series configuration. Results show that the combination of DoE and one-dimensional simulation for the design of camshaft contours is well suited which was also validated with experimental results. Furthermore, the potential of residual gas retention by favorable configurations with a second event already revealed in various publications could be confirmed with respect to exhaust gas temperature increase and engine efficiency.

Effect of the Fuel Injection Strategy on Diesel Particulate Filter Regeneration in a Single-Cylinder Diesel Engine

2016 ◽  
Vol 138 (10) ◽  
Author(s):  
Sungjun Yoon ◽  
Hongsuk Kim ◽  
Daesik Kim ◽  
Sungwook Park
Keyword(s):  
Fuel Injection ◽  
Injection Pressure ◽  
Operating Conditions ◽  
Particulate Filter ◽  
Exhaust Gas ◽  
Gas Temperature ◽  
Diesel Particulate ◽  
Injection Strategy ◽  
Dpf Regeneration ◽  
Exhaust Gas Temperature

Stringent emission regulations (e.g., Euro-6) have forced automotive manufacturers to equip a diesel particulate filter (DPF) on diesel cars. Generally, postinjection is used as a method to regenerate the DPF. However, it is known that postinjection deteriorates the specific fuel consumption and causes oil dilution for some operating conditions. Thus, an injection strategy for regeneration is one of the key technologies for diesel powertrains equipped with a DPF. This paper presents correlations between the fuel injection strategy and exhaust gas temperature for DPF regeneration. The experimental apparatus consists of a single-cylinder diesel engine, a DC dynamometer, an emission test bench, and an engine control system. In the present study, the postinjection timing was in the range of 40 deg aTDC to 110 deg aTDC and double postinjection was considered. In addition, the effects of the injection pressure were investigated. The engine load was varied among low load to midload conditions, and the amount of fuel of postinjection was increased up to 10 mg/stk. The oil dilution during the fuel injection and combustion processes was estimated by the diesel loss measured by comparing two global equivalences ratios: one measured from a lambda sensor installed at the exhaust port and one estimated from the intake air mass and injected fuel mass. In the present study, the differences of the global equivalence ratios were mainly caused by the oil dilution during postinjection. The experimental results of the present study suggest optimal engine operating conditions including the fuel injection strategy to obtain an appropriate exhaust gas temperature for DPF regeneration. The experimental results of the exhaust gas temperature distributions for various engine operating conditions are discussed. In addition, it was revealed that the amount of oil dilution was reduced by splitting the postinjection (i.e., double postinjection). The effects of the injection pressure on the exhaust gas temperature were dependent on the combustion phasing and injection strategies.

Assessment of a Syngas-Diesel Dual Fuelled Compression Ignition Engine

2010 ◽  
Author(s):  
Bibhuti B. Sahoo ◽  
Niranjan Sahoo ◽  
Ujjwal K. Saha
Keyword(s):  
Diesel Engine ◽  
Thermal Efficiency ◽  
Gas Flow ◽  
Direct Injection ◽  
Dual Fuel ◽  
Exhaust Gas ◽  
Compression Ignition ◽  
Gas Temperature ◽  
Compression Ignition Engine ◽  
Exhaust Gas Temperature

Synthesis gas (Syngas), a mixture of hydrogen and carbon monoxide, can be manufactured from natural gas, coal, petroleum, biomass, and even from organic wastes. It can substitute fossil diesel as an alternative gaseous fuel in compression ignition engines under dual fuel operation route. Experiments were conducted in a single cylinder, constant speed and direct injection diesel engine fuelled with syngas-diesel in dual fuel mode. The engine is designed to develop a power output of 5.2 kW at its rated speed of 1500 rpm under variable loads with inducted syngas fuel having H2 to CO ratio of 1:1 by volume. Diesel fuel as a pilot was injected into the engine in the conventional manner. The diesel engine was run at varying loads of 20, 40, 60, 80 and 100%. The performance of dual fuel engine is assessed by parameters such as thermal efficiency, exhaust gas temperature, diesel replacement rate, gas flow rate, peak cylinder pressure, exhaust O2 and emissions like NOx, CO and HC. Dual fuel operation showed a decrease in brake thermal efficiency from 16.1% to a maximum of 20.92% at 80% load. The maximum diesel substitution by syngas was found 58.77% at minimum exhaust O2 availability condition of 80% engine load. The NOx level was reduced from 144 ppm to 103 ppm for syngas-diesel mode at the best efficiency point. Due to poor combustion efficiency of dual fuel operation, there were increases in CO and HC emissions throughout the range of engine test loads. The decrease in peak pressure causes the exhaust gas temperature to rise at all loads of dual fuel operation. The present investigation provides some useful indications of using syngas fuel in a diesel engine under dual fuel operation.

Performance Characteristics of a Diesel Engine Fueled With Avio-Kerosene

2003 ◽  
Author(s):  
Giancarlo Chiatti ◽  
Ornella Chiavola
Keyword(s):  
Diesel Engine ◽  
Combustion Chamber ◽  
Gas Turbine ◽  
Power Output ◽  
Pressure Rise ◽  
Experimental Tests ◽  
Diesel Oil ◽  
Exhaust Gas ◽  
Gas Temperature ◽  
Exhaust Gas Temperature

A comparative series of experimental tests has been performed on a 4-stroke multi cylinder indirect injection diesel engine fueled with diesel oil, pure gas-turbine fuel and gas-turbine fuel with additives. The engine has been equipped aimed at monitoring both the overall performances and the variation with time of the pressure in the pre-combustion chamber. Some key parameters have been investigated at different engine speeds and loads (ignition delay, pressure rise in the pre-combustion chamber, power output, specific fuel consumption, exhaust gas temperature) and discussed results are presented.

Investigations on Low Heat Rejection Diesel Engine With Crude Jatropha Oil as an Alternate Fuel

2002 ◽  
Author(s):  
M. V. S. Murali Krishna ◽  
C. M. Vara Prasad ◽  
Tandur Rajashekar ◽  
Supriya Tiwari ◽  
T. Sujani
Keyword(s):  
Diesel Engine ◽  
Diesel Fuel ◽  
Injection Pressure ◽  
High Viscosity ◽  
Injection Timing ◽  
Jatropha Oil ◽  
Heat Rejection ◽  
Reduction Of Nox ◽  
Conventional Diesel Fuel ◽  
Diesel Operation

Jatropha oil, a non-edible vegetable oil shows a greater potential for replacing conventional diesel fuel quite effectively, as its properties are compatible to that of diesel fuel. But low volatility and high viscosity of jatropha oil call for hot combustion chamber, which is provided by a low heat rejection diesel engine with threaded air gap piston and liner with superni-90 inserts. The performance of the engine with jatropha oil is obtained with different versions of the engine such as conventional engine and insulated engine at normal and preheat condition of the oil, with varying injection pressure and timing and compared to the engine with pure diesel operation at recommended injection pressure and timing. Increase of thermal efficiency of 18% and reduction of NOx levels by 5% are observed at optimized injection timing and at higher injection pressure with insulated engine at preheat condition of jatropha oil in comparison with pure diesel operation on conventional engine.

Sign in / Sign up

Export Citation Format

Share Document