Assessment of a Syngas-Diesel Dual Fuelled Compression Ignition Engine

2010 ◽  
Author(s):  
Bibhuti B. Sahoo ◽  
Niranjan Sahoo ◽  
Ujjwal K. Saha
Keyword(s):  
Diesel Engine ◽  
Thermal Efficiency ◽  
Gas Flow ◽  
Direct Injection ◽  
Dual Fuel ◽  
Exhaust Gas ◽  
Compression Ignition ◽  
Gas Temperature ◽  
Compression Ignition Engine ◽  
Exhaust Gas Temperature

Synthesis gas (Syngas), a mixture of hydrogen and carbon monoxide, can be manufactured from natural gas, coal, petroleum, biomass, and even from organic wastes. It can substitute fossil diesel as an alternative gaseous fuel in compression ignition engines under dual fuel operation route. Experiments were conducted in a single cylinder, constant speed and direct injection diesel engine fuelled with syngas-diesel in dual fuel mode. The engine is designed to develop a power output of 5.2 kW at its rated speed of 1500 rpm under variable loads with inducted syngas fuel having H2 to CO ratio of 1:1 by volume. Diesel fuel as a pilot was injected into the engine in the conventional manner. The diesel engine was run at varying loads of 20, 40, 60, 80 and 100%. The performance of dual fuel engine is assessed by parameters such as thermal efficiency, exhaust gas temperature, diesel replacement rate, gas flow rate, peak cylinder pressure, exhaust O2 and emissions like NOx, CO and HC. Dual fuel operation showed a decrease in brake thermal efficiency from 16.1% to a maximum of 20.92% at 80% load. The maximum diesel substitution by syngas was found 58.77% at minimum exhaust O2 availability condition of 80% engine load. The NOx level was reduced from 144 ppm to 103 ppm for syngas-diesel mode at the best efficiency point. Due to poor combustion efficiency of dual fuel operation, there were increases in CO and HC emissions throughout the range of engine test loads. The decrease in peak pressure causes the exhaust gas temperature to rise at all loads of dual fuel operation. The present investigation provides some useful indications of using syngas fuel in a diesel engine under dual fuel operation.

Effect of Water Injection in Acetylene-Diesel Dual Fuel DI Diesel Engine

2012 ◽  
Author(s):  
T. Lakshmanan ◽  
A. Khadeer Ahmed ◽  
G. Nagarajan
Keyword(s):  
Diesel Engine ◽  
Thermal Efficiency ◽  
Alternative Fuels ◽  
Gas Flow ◽  
Water Injection ◽  
Intake Manifold ◽  
Dual Fuel ◽  
Intake Port ◽  
Gas Temperature ◽  
Brake Thermal Efficiency

Gaseous fuels are good alternative fuels to improve the energy crisis of today’s situation due to its clean burning characteristics. However, the incidence of backfire and knock remains a significant barrier in commercialization. With the invention of latest technology, the above barriers are eliminated. One such technique is timed injection of water into the intake port. In the present investigation, acetylene was aspirated in the intake manifold of a single cylinder diesel engine, with a gas flow rate of 390 g/h, along with water injected in the intake port, to overcome the backfire and knock problems in gaseous dual fuel engine. The brake thermal efficiency and emissions such as NOx, smoke, CO, HC, CO2 and exhaust gas temperature were studied. Dual fuel operation of acetylene induction with injection of water results in lowered NOx emissions with complete elimination of backfire and knock at the expense of brake thermal efficiency.

Factors Affecting Performance of Dual Fuel Compression Ignition Engines

2013 ◽  
Vol 388 ◽  
pp. 217-222
Author(s):  
Mohamed Mustafa Ali ◽  
Sabir Mohamed Salih
Keyword(s):  
Diesel Engine ◽  
Fuel Consumption ◽  
Thermal Efficiency ◽  
Fuel Injection ◽  
Direct Injection ◽  
Injection System ◽  
Dual Fuel ◽  
Injection Timing ◽  
Compression Ignition ◽  
Factors Affecting

Compression Ignition Diesel Engine use Diesel as conventional fuel. This has proven to be the most economical source of prime mover in medium and heavy duty loads for both stationary and mobile applications. Performance enhancements have been implemented to optimize fuel consumption and increase thermal efficiency as well as lowering exhaust emissions on these engines. Recently dual fueling of Diesel engines has been found one of the means to achieve these goals. Different types of fuels are tried to displace some of the diesel fuel consumption. This study is made to identify the most favorable conditions for dual fuel mode of operation using Diesel as main fuel and Gasoline as a combustion improver. A single cylinder naturally aspirated air cooled 0.4 liter direct injection diesel engine is used. Diesel is injected by the normal fuel injection system, while Gasoline is carbureted with air using a simple single jet carburetor mounted at the air intake. The engine has been operated at constant speed of 3000 rpm and the load was varied. Different Gasoline to air mixture strengths investigated, and diesel injection timing is also varied. The optimum setting of the engine has been defined which increased the thermal efficiency, reduced the NOx % and HC%.

Impact of Oxygenated Additives on Performance Characteristics of Methyl Ester in IC Engine

2016 ◽  
Vol 852 ◽  
pp. 724-728 ◽  
Author(s):  
D. Yuvarajan ◽  
K. Pradeep ◽  
S. Magesh Kumar
Keyword(s):  
Thermal Efficiency ◽  
Butyl Alcohol ◽  
Exhaust Gas ◽  
Gas Temperature ◽  
Compression Ignition Engine ◽  
Ic Engine ◽  
Oxygenated Additives ◽  
Lower Viscosity ◽  
Exhaust Gas Temperature ◽  
The Impact

In this present work, the impact of blending n-butyl alcohol, a next generation biofuel with jatropha biodiesel on the performance of a diesel engine are examined. Tests were performed on a constant speed compression ignition engine using n-butyl alcohol / jatropha biodiesel blends. N-butyl alcohol was added to jatropha biodiesel by 10, 20 and 30% by volume. Performance parameters namely break thermal efficiency (BTE), Brake specific fuel consumption (BSFC) and Exhaust gas temperature (EGT) were analyzed in this work. It was experimentally found that by adding n-butyl alcohol to neat jatropha biodiesel, significant reduction in viscosity was observed. In addition, break thermal efficiency was increased by 0.8 % due to improved atomization of the blends. Further, brake specific fuel and exhaust gas temperature was further reduced due to lower viscosity and improved combustion rate with addition of n-butyl alcohol to jatropha biodiesel.

Study of the Variations in Cylinder-Exhaust-Gas Temperature Over Inlet Air and Operation-Input Parameters of Compression-Ignition Engines

2014 ◽  
Vol 136 (6) ◽  
Author(s):  
Gong Chen
Keyword(s):  
Air Temperature ◽  
Thermal Loading ◽  
Exhaust Emissions ◽  
Exhaust Gas ◽  
Compression Ignition ◽  
Gas Temperature ◽  
Compression Ignition Engine ◽  
Engine Operation ◽  
Compression Ignition Engines ◽  
Exhaust Gas Temperature

Cylinder-exhaust-gas temperature (Texh) of a turbocharged compression-ignition engine indicates the levels of engine thermal loading on cylinder and exhaust components, thermal efficiency performance, and engine exhaust emissions. In consideration that Texh is affected by engine air inlet condition that primarily includes inlet air temperature (Ti) and pressure (pi), this paper studies the variation (ΔTexh) of Texh over varying the engine inlet air parameters of compression-ignition engines. The study is to understand ΔTexh with appropriate relations between the inlet parameters and Texh being identified and simply modeled. The regarded effects on Texh and ΔTexh for both naturally aspirated and turbocharged engines of this type are analyzed and predicted. The results indicate that Texh increases as Ti increases or pi decreases. The rate of variation in ΔTexh over varying Ti or pressure pi is smaller in a turbocharged engine than that in a naturally aspirated engine, as reflected from the model and results of the analysis. The results also indicate, for instance, Texh would increase approximately by ∼2 °C as Ti increases by 1 °C or increase by ∼35 °C as pi decreases by 10−2 MPa, as predicted for a typical high-power turbocharged diesel engine operating at a typical full-load condition. The design and operating parameters significant in influencing ΔTexh along with varying Ti or pi are studied in addition. These include the degree of engine cylinder compression, the level of intake manifold air temperature, the magnitude of intake air boost, and the quantity of cycle combustion thermal input. As those parameters change, the rate of variation in Texh varies. For instance, the results indicate that the rate of ΔTexh versus the inlet air parameters would increase as the quantity of cycle combustion thermal input becomes higher. With the understanding of ΔTexh, the engine output performances of thermal loading, efficiency, and exhaust emissions, concerning engine operation at variable ambient temperature or pressure, can be understood and evaluated for the purpose of engine analysis, design, and optimization.

scholarly journals An Experimental Study on the Performance Characteristics of a Diesel Engine Fueled with ULSD-Biodiesel Blends

2020 ◽  
Vol 10 (2) ◽  
pp. 183-190
Author(s):  
Viet Dung Tran ◽  
Anh Tuan Le ◽  
Anh Tuan Hoang
Keyword(s):  
Diesel Engine ◽  
Fuel Consumption ◽  
Thermal Efficiency ◽  
Cooling System ◽  
Specific Fuel Consumption ◽  
Exhaust Gas ◽  
Gas Temperature ◽  
Brake Thermal Efficiency ◽  
Exhaust Gas Temperature ◽  
Low Sulfur

As a rule, the highest permissible sulfur content in the marine fuel must drop below 0.5% from 1 January 2020 for global fleets. As such, ships operating in emission control areas must use low sulfur or non-sulfur fuel to limit sulfur emissions as a source of acid rain. However, that fact has revealed two challenges for the operating fleet: the very high cost of ultra-low sulfur diesel (ULSD) and the installation of the fuel conversion system and the ULSD cooling system. Therefore, a solution that blends ULSD and biodiesel (BO) into a homogeneous fuel with properties equivalent to that of mineral fuels is considered to be significantly effective. In the current work, an advanced ultrasonic energy blending technology has been applied to assist in the production of homogeneous ULSD-BO blends (ULSD, B10, B20, B30, and B50 with blends of coconut oil methyl ester with ULSD of 10%, 20%, 30% and 50% by volume) which is supplied to a small marine diesel engine on a dynamo test bench to evaluate the power and torque characteristics, also to consider the effect of BO fuel on specific fuel consumption exhaust gas temperature and brake thermal efficiency. The use of the ultrasonic mixing system has yielded impressive results for the homogeneous blend of ULSD and BO, which has contributed to improved combustion quality and thermal efficiency. The results have shown that the power, torque, and the exhaust gas temperature, decrease by approximately 9%, 2%, and 4% respectively with regarding the increase of the blended biodiesel rate while the specific fuel consumption and brake thermal efficiency tends to increase of around 6% and 11% with those blending ratios.

Effect of Load Level on the Performance of a Dual Fuel Compression Ignition Engine Operating on Syngas Fuels With Varying H2/CO Content

2011 ◽  
Vol 133 (12) ◽  
Author(s):  
B. B. Sahoo ◽  
U. K. Saha ◽  
N. Sahoo
Keyword(s):  
Diesel Engine ◽  
Thermal Efficiency ◽  
Peak Pressure ◽  
Gaseous Fuel ◽  
Dual Fuel ◽  
Engine Fuel ◽  
Compression Ignition ◽  
Compression Ignition Engine ◽  
Engine Operation ◽  
Brake Thermal Efficiency

Syngas, an environmentally friendly alternative gaseous fuel for internal combustion engine operation, mainly consists of carbon monoxide (CO) and hydrogen (H2). It can substitute fossil diesel oil in a compression ignition diesel engine through dual fuel operation route. In the present investigation, experiments were conducted in a constant speed single cylinder direct injection diesel engine fuelled with syngas-diesel in a dual fuel operation mode. The main contribution of this study is to introduce the new synthetic gaseous fuel (syngas) including the possible use of CO gas, an alternative diesel engine fuel. In this work, four different H2 and CO compositions of syngas were chosen for dual fuel study under different engine loading levels. Keeping the same power output at the corresponding tested loads, the engine performance of dual fuel operations were compared to that of diesel mode for the entire load range. The maximum diesel replacement in the engine was found to be 72.3% for 100% H2 fuel. This amount replacement rate was reduced for the low energetic lower H2 content fuels. The brake thermal efficiency was always found highest (about 21%) in the case of diesel mode operation. However, the 100% H2 syngas showed a comparative performance level with diesel mode at the expense of higher NOx emissions. At 80% engine load, the brake thermal efficiency was found to be 15.7% for 100% CO syngas. This value increased to 16.1%, 18.3% and 19.8% when the 100% CO syngas composition was replaced by H2 contents of 50%, 75% and 100%, respectively. At part loads (i.e., at 20% and 40%), dual fuel mode resulted a poor performance including higher emission levels. In contrast, at higher loads, syngas fuels showed a good competitive performance to diesel mode. At all the tested loads, the NOx emission was observed highest for 100% H2 syngas as compared to other fuel conditions, and a maximum of 240 ppm was found at 100% load. However, when the CO fractions of 25%, 50% and 100%, were substituted to hydrogen fuel, the emission levels got reduced to 175 ppm, 127 ppm, and 114 ppm, respectively. Further, higher CO and HC emission levels were recorded for 25%, 50%, and 100% CO fraction syngas fuels due to their CO content. Ignition delay was found to increase for the dual fuel operation as compared to diesel mode, and also it seemed to be still longer for higher H2 content syngas fuels. The peak pressure and maximum rate of pressure rise were found to decrease for all the cases of dual fuel operation, except for 100% H2 syngas (beyond 60% load). The reduction in peak pressure resulted a rise in the exhaust gas temperature at all loads under dual fuel operation. The present investigation provides some useful experimental data which can be applied to the possible existing engine parameters modifications to produce a competitive syngas dual fuel performance at all the loading operations.

scholarly journals ALDEHYDE EMISSIONS FROM A STATIONARY DIESEL ENGINE OPERATING WITH CASTOR OIL BIODIESEL – DIESEL OIL BLENDS

2010 ◽  
Vol 9 (1-2) ◽  
pp. 35 ◽  
Author(s):  
P. B. Zarante ◽  
M. J. Da Silva ◽  
O. S. Valente ◽  
J. R. Sodré
Keyword(s):  
Diesel Engine ◽  
Castor Oil ◽  
Direct Injection ◽  
Diesel Oil ◽  
Exhaust Gas ◽  
Compression Ignition ◽  
Compression Ignition Engine ◽  
Oil Blends ◽  
Fuel Blends ◽  
Flame Ionization

The presence of aldehyde in the exhaust gas of a stationary, direct injection, compression ignition engine operating with castor oil biodiesel/diesel oil blends (B5, B10, B20 and B35) is analyzed. The diesel engine was operated with constant speed of 1800 rev/min and load of 37.5 kW. The gas sample was collected directly from the exhaust. Aldehydes were identified and quantified using gas chromatography (GC) with flame ionization detector analyzer (FID). Acetaldehyde presented higher exhaust concentration than formaldehyde for all fuel blends tested. In general, the exhaust aldehyde levels were very low and did not present significant differences between the fuel blends tested.

Evaluating the Influence of Biogas Flow Rate and Addition of Cerium Oxide Nanoparticles on the Performance of a Dual Fuel Engine Using Taguchi Method

2017 ◽  
Vol 17 ◽  
pp. 179-193
Author(s):  
M. Feroskhan ◽  
Ismail Saleel
Keyword(s):  
Cerium Oxide ◽  
Flow Rate ◽  
Thermal Efficiency ◽  
Equivalence Ratio ◽  
Volumetric Efficiency ◽  
Dual Fuel ◽  
Exhaust Gas ◽  
Gas Temperature ◽  
Brake Thermal Efficiency ◽  
Exhaust Gas Temperature

Biogas is a promising alternative fuel for compression ignition (CI) engines owing to its renewability and carbon neutrality. In this study, biogas was used along with diesel in a CI engine in dual fuel mode, i.e. biogas is inducted along with air and this mixture is ignited by the in-cylinder injection of diesel. The viability of using cerium oxide (CeO2) nanoparticles as an additive to diesel was also explored. The effects of three parameters, viz. biogas flow rate and concentration of CeO2 nanoparticles and applied load on engine performance were investigated under constant speed operation. These parameters were varied in the ranges of 0 - 12 litre/min, 0 - 35 mg/litre and 5 - 22 N.m respectively. The experimental test matrix was reduced to 16 trials using Taguchi’s approach. Performance was quantified in terms of brake thermal efficiency, volumetric efficiency, diesel consumption, exhaust gas temperature and overall equivalence ratio. The criteria for optimum performance were defined as maximum brake thermal and volumetric efficiencies and minimum diesel consumption, exhaust gas temperature and overall equivalence ratio. Optimum operating conditions were identified by evaluating the signal to noise ratio (SNR) for each performance parameter and using the higher-the-better (HTB) or lower-the-better (LTB) condition as applicable. Contributions of individual parameters towards the performance indices were found using ANOVA. Load was found to be the main contributing factor for brake thermal efficiency, exhaust gas temperature and overall equivalence ratio. Biogas flow rate showed significant contribution towards volumetric efficiency. Biogas flow rate and load had comparable influences on diesel consumption. Addition of nanoparticles showed minor contribution towards all the performance parameters.

scholarly journals Research on the experimental performance of gas-fired boiler based on the total heat recovery technology of absorption heat pump

2021 ◽  
Vol 261 ◽  
pp. 01059
Author(s):  
Xujing Zhai ◽  
Shoutao Tian ◽  
Kelin Zhu ◽  
Pan Huang ◽  
Jin Yu ◽  
...  
Keyword(s):  
Energy Saving ◽  
Heat Pump ◽  
Thermal Efficiency ◽  
Heat Recovery ◽  
Gas Flow ◽  
Exhaust Gas ◽  
Gas Temperature ◽  
Absorption Heat Pump ◽  
Reconstruction Project ◽  
Exhaust Gas Temperature

Based on an example of a gas-fired boiler for an industrial user in Tianjin, the absorption heat pump technology was used to carry out energy-saving transformation of the above boiler. The actual test was carried out on the gas flow, exhaust gas temperature and other parameters from January 2, 2018 to February 26, 2018. And then, the thermal efficiency of the boiler was analysed. The results show that after the energy-saving transformation, the exhaust gas temperature of the gas-fired boiler can be reduced from 140 °C to about 40 °C, and the overall thermal efficiency of the boiler also rises from 89.5% to 101.3%, which is 13.2% higher than that before optimization. According to the economic analysis, the energy-saving reconstruction project can achieve an energy-saving economic benefit of 1.598 million yuan throughout the year, with obvious energy-saving and emission reduction benefits.

Sign in / Sign up

Export Citation Format

Share Document