ANALISIS PENERAPAN KESELAMATAN KERJA DALAM UPAYA PENGENDALIAN KECELAKAAN KERJA DI PT. BUDI DWIYASA PERKASA

2017 ◽  
Vol 1 (2) ◽  
Author(s):  
Farah Alhamid ◽  
Keyword(s):  
Risk Assessment ◽  
Hazard Analysis ◽  
Assessment Method ◽  
Hazard Identification ◽  
Risk Level ◽  
Protective Equipment ◽  
Risk Assessment Method ◽  
Accident Data ◽  
Plantation Company ◽  
Work Done

Abstract In conducting activities, many found workers who did not use personal protective equipment, do not pay attention to safety in work and work done like without procedure. PT. Budi Dwiyasa Perkasais a plantation company palm oil. Based on accident data obtained work, there are 14 case of accident in April until June 2016 in PT. Budi Dwiyasa Perkasa. A major factor cause of the accident is unsafe actions and unsafe conditions. Hazard analysis needs to be done in order to prevent the accident of work. Hazard identification done with using the risk assessment method. This analysis of the technique used to determine the level of the risk of a job is a combination of between the possibility of the harms caused by the severity of the caused. The result of hazard identification with this method is used in a kind of work to have a high risk level and need to address special in order to prevent the accident.

scholarly journals ANALISIS PENERAPAN KESELAMATAN KERJA DALAM UPAYA PENGENDALIAN KECELAKAAN KERJA DI PT. BUDI DWIYASA PERKASA

2019 ◽  
Vol 3 (1) ◽  
Author(s):  
Riana Septiani ◽  
Keyword(s):  
Hazard Analysis ◽  
Assessment Method ◽  
Hazard Identification ◽  
Risk Level ◽  
Accident Risk ◽  
Risk Assessment Method ◽  
Accident Data ◽  
Safety Accident ◽  
Plantation Company ◽  
Work Done

Abstract In conducting activities, many found workers who did not use personal protective equipment, do not pay attention to safety in work and work done like without procedure. PT. Budi Dwiyasa Perkasais a plantation company palm oil. Based on accident data obtained work, there are 14 case of accident in April until June 2016 in PT. Budi Dwiyasa Perkasa. A major factor cause of the accident is unsafe actions and unsafe conditions. Hazard analysis needs to be done in order to prevent the accident of work. Hazard identification done with using the risk assessment method. This analysis of the technique used to determine the level of the risk of a job is a combination of between the possibility of the harms caused by the severity of the caused. The result of hazard identification with this method is used in a kind of work to have a high risk level and need to address special in order to prevent the accident. Keywords: safety, accident, risk, hazard identification,

scholarly journals Risk control analysis of a furniture production activities using hazard identification and risk assessment method

2018 ◽  
Vol 154 ◽  
pp. 01102 ◽  
Author(s):  
Sri Indrawati ◽  
Atyanti Dyah Prabaswari ◽  
M. Abdul Fitriyanto
Keyword(s):  
Risk Assessment ◽  
Technological Development ◽  
Risk Control ◽  
Assessment Method ◽  
Hazard Identification ◽  
Worker Safety ◽  
Risk Level ◽  
Control Analysis ◽  
Use Of Technology ◽  
Risk Assessment Method

The furniture industry in Indonesia is growing rapidly that leads to technological development. But the use of technology in the industry creates some risk to worker safety. The number of work accidents in Indonesia at the end of 2016 is relatively high. Therefore, this research is conducted to identify hazards and determine risk control using hazard identification and risk assessment method (HIRA). There are three main stages, i.e. identify and analyze hazards, classify hazards and risk control. The result shows that there are nine potential hazards in furniture production, 22% of it is categorized as high risk level, i.e. hand slashed and fingers cut by machine. Three types of risk control activities are determined to minimize the risk, i.e. administration and engineering control and personal protective equipment.

scholarly journals Analisis Risiko Keselamatan dan Kesehatan Kerja (K3) dengan Metode Hazard Analysis (Studi Kasus pada Proyek Pembangunan Perumahan)

2020 ◽  
Vol 5 (1) ◽  
pp. 29
Author(s):  
Nidya Wisudawati ◽  
Rurry Patradhiani
Keyword(s):  
Risk Assessment ◽  
Hazard Analysis ◽  
Risk Control ◽  
Hazard Identification ◽  
Risk Level

Risiko kecelakaan kerja merupahal hal yang tak dapat dihindari dari kegiatan proyek pembangunan. PT Gran Anugerah Wijaya merupakan pengusaha pengembang perumahan yang sedang mengerjakan proyek pembangunanan 58 unit rumah tipe 36 yang berlokasi di daerah Palembang. Dari hasil pengamatan lapangan, alur proses pembangunan rumah yang dikerjakan meliputi pemasangan pondasi, pemasangan dinding, pemasangan kusen kayu, pemasangan rangka atap dan finishing. Hazard Identification, Risk Assessment dan Risk Control telah dilakukan dlaam penelitian ini. Hasil yang didapat bahwa terdapat 27 potensi risiko dengan risk level diantara rendah hinggi tinggi. Pengendalian risiko yang bisa dilakaukan untuk mengurangi bahaya kerja terhadap karyawan bangunan diantaranya substitusi, administrasi dan Alat Pelindung Diri (APD).

A New Fine-Kinney Method Based on Clustering Approach

2020 ◽  
Vol 28 (03) ◽  
pp. 497-512
Author(s):  
Cansu Dagsuyu ◽  
Murat Oturakci ◽  
Esra Sarac Essiz
Keyword(s):  
Risk Assessment ◽  
Conventional Method ◽  
Clustering Algorithms ◽  
Assessment Method ◽  
Distance Functions ◽  
Risk Level ◽  
New Approach ◽  
Clustering Techniques ◽  
Risk Assessment Method ◽  
Clustering Approach

In this study, a new approach to Fine-Kinney risk assessment method is developed in order to overcome the limitations of the conventional method with clustering algorithms. New risk level of classes are attempted to determine with K-Means and Hierarchical clustering algorithms with using two different distance functions which are Euclidean and Manhattan distances. According to the results, K-Means algorithms have provided accurate and sensitive cluster of classes. Classes from conventional and K-Means algorithms are applied and compared to the identified risks of a workshop of a medium sized textile company. Results of the study indicate that clustering techniques are new, original and applicable way to define new classes in order to prioritize risks by overcoming the drawbacks of conventional Fine-Kinney method.

Risk Assessment of Tractor-Related Hazards Based on Accident Cases

2019 ◽  
Vol 25 (3) ◽  
pp. 133-152
Author(s):  
Byounggap Kim ◽  
Seongyoon Lim ◽  
Seung-Yeoub Shin ◽  
Sunghyun Yum ◽  
Yu-Yong Kim ◽  
...  
Keyword(s):  
Risk Assessment ◽  
South Korea ◽  
Risk Evaluation ◽  
Frequency Estimation ◽  
Assessment Method ◽  
Hazard Identification ◽  
Expert Review ◽  
Risk Assessment Method ◽  
Survey Results ◽  
Statistical Results

Abstract. Annually, tractor accidents are estimated to account for more than 100 deaths in South Korea. Periodic accident surveys have served as an essential means for the National Institute of Agricultural Sciences (NAS) to develop strategies to prevent tractor accidents. In this study, hazards leading to accidents were identified, and their risks were assessed based on survey results to establish a more effective accident prevention strategy. Risk assessment for hazards proceeded as follows: hazard identification, frequency estimation, number of equivalent fatalities (NEF) estimation, and finally risk evaluation. Hazards were identified by analyzing 588 accident cases from NAS surveys and performing an expert review of the analysis results by implementing a Delphi survey. The frequency and NEF of each hazard were estimated by multiplying its probabilities and the statistical results of the NAS surveys. Each hazard was plotted in a frequency-NEF (FN) diagram and evaluated according to its position. Fifty-four hazards were identified, and their frequencies and NEF values were estimated. The risk evaluation results, based on the FN diagram, revealed that no hazard was located in the “unacceptable” area, and two hazards (carelessness and not looking ahead carefully) were in the “as low as reasonably practicable” area. Thus, it is critical to mitigate the effects of these two hazards. With the risk assessment method used in this study, personnel who are engaged in the prevention of tractor accidents, such as policymakers, extension specialists, and researchers, can quantitatively predict how many cases or fatalities can be reduced by eliminating a certain hazard. Keywords: Equivalent fatality, Frequency estimation, Hazard identification, Risk assessment, Tractor accident.

scholarly journals A Dynamic Risk Assessment Method for Deep-Buried Tunnels Based on a Bayesian Network

Geofluids ◽  
2020 ◽  
Vol 2020 ◽  
pp. 1-14 ◽  
Author(s):  
Yan Wang ◽  
Jie Su ◽  
Sulei Zhang ◽  
Siyao Guo ◽  
Peng Zhang ◽  
...  
Keyword(s):  
Risk Assessment ◽  
Bayesian Network ◽  
Influencing Factors ◽  
Assessment Method ◽  
Assessment Model ◽  
Risk Level ◽  
Dynamic Risk ◽  
Risk Rating ◽  
Risk Assessment Method ◽  
Dynamic Risk Assessment

In view of the shortcomings in the risk assessment of deep-buried tunnels, a dynamic risk assessment method based on a Bayesian network is proposed. According to case statistics, a total of 12 specific risk rating factors are obtained and divided into three types: objective factors, subjective factors, and monitoring factors. The grading criteria of the risk rating factors are determined, and a dynamic risk rating system is established. A Bayesian network based on this system is constructed by expert knowledge and historical data. The nodes in the Bayesian network are in one-to-one correspondence with the three types of influencing factors, and the probability distribution is determined. Posterior probabilistic and sensitivity analyses are carried out, and the results show that the main influencing factors obtained by the two methods are basically the same. The constructed dynamic risk assessment model is most affected by the objective factor rating and monitoring factor rating, followed by the subjective factor rating. The dynamic risk rating is mainly affected by the surrounding rock level among the objective factors, construction management among the subjective factors, and arch crown convergence and side wall displacement among the monitoring factors. The dynamic risk assessment method based on the Bayesian network is applied to the No. 3 inclined shaft of the Humaling tunnel. According to the adjustment of the monitoring data and geological conditions, the dynamic risk rating probability of level I greatly decreased from 81.7% to 33.8%, the probability of level II significantly increased from 12.3% to 34.0%, and the probability of level III increased from 5.95% to 32.2%, which indicates that the risk level has risen sharply. The results show that this method can effectively predict the risk level during tunnel construction.

scholarly journals ANALISIS RISIKO KECELAKAAN KERJA METODE HIRA (HAZARD IDENTIFICATION AND RISK ASSESSMENT) DI PT. X

2021 ◽  
Vol 5 (2) ◽  
pp. 1104-1012
Author(s):  
Wita Afnella ◽  
Tri Niswati Utami
Keyword(s):  
Risk Assessment ◽  
Qualitative Method ◽  
Assessment Method ◽  
Hazard Identification ◽  
Small Risk ◽  
Risk Assessment Method ◽  
Tolerable Risk ◽  
Substantial Risk ◽  
Work Accidents ◽  
Initial Survey

The HIRA (Hazard Identification, Risk Assessment) method is a process of identifying hazards that occur in all company activities, then conducting a risk assessment of the hazards that occur. Introduction: Based on the initial survey conducted at PT. X, it was found that there were work accidents such as pinched hands, cuts, entanglement in processing machines which caused the risk of accidents. This research was conducted at PT.X in February-August 2021. Methods: This study used a descriptive qualitative method. This study analyzes the risk of work accidents using the HIRA (Hazard Identification, Risk Assessment) method which aims to identify hazards and conduct a risk assessment of these hazards. The research informants were 6 people consisting of 2 key informants and 4 main informants. Results: The results showed that there were 44 types of hazards from 8 work stations at PT. X. Among them, 16% have a small risk of harm (trivial), 38.6% have a tolerable risk, 34.1% have a moderate risk of harm, 4.5% have a substantial risk of harm, 6, 8% have an intolerable risk of harm. Conclusion: Risk analysis is a process by which hazards are identified and risks are estimated to assess the damage caused with the likelihood of damage occurring.

scholarly journals MANAJEMEN PENGANGKUTAN BARANG KIMIA BERBAHAYA: TINJAUAN KESELAMATAN DAN PEMENUHAN REGULASI

2020 ◽  
Vol 2 (1) ◽  
pp. 1-16
Author(s):  
Syaiful Barkah ◽  
Alugoro Mulyowahyudi
Keyword(s):  
Risk Assessment ◽  
Analytical Method ◽  
Safety Management ◽  
Assessment Method ◽  
Hazard Identification ◽  
Risk Assessments ◽  
Hazardous Chemicals ◽  
Government Regulations ◽  
Risk Assessment Method ◽  
Objective Program

This study analyzes the safety management of transporting dangerous chemical goods that are transported from the factory to the customer. By conducting a risk assessment of transportation activities and reviewing company compliance with regulations and laws. This research is descriptive qualitative or observational, the analytical method used in this study is the HIRADC (Hazard Identification Detemining Control Risk Assessment) method. The results of this study provide an overview of the level of safety of transporting hazardous chemicals to carry out risk assessments in shipping goods to customers. Risks that score more than 1 are risks that must be followed up by making an objective program. The level of risk comes from a combination of likelihood (probability) and severity of impact (consequences). The results of this study are expected to be used to control and reduce current risks. Evaluation of company compliance with government regulations and legislation, can be used as a basis for developing compliance plans that were not previously met.

Sign in / Sign up

Export Citation Format

Share Document