scholarly journals Effect of Solar Tilt Angles on Photovoltaic Module Performance: A Behavioral Optimization Approach

2020 ◽  
pp. 90-102
Author(s):  
Trina Som ◽  
A. Sharma ◽  
D. Thakur
Keyword(s):  
Solar Energy ◽  
Tilt Angle ◽  
Photovoltaic Module ◽  
Optimization Approach ◽  
Solar Module ◽  
Monthly Average ◽  
Pv Module ◽  
Yearly Maximum ◽  
Module Performance ◽  
Better Than

In the present study, performance analyses of a solar module are made through the optimal variation of solar tilt angle, pertaining to the maximum generation of solar energy. The work has been carried out for a particular location at Tripura, in India, considering three different cases on an annual basis. An intelligent behavioural based algorithm, known as artificial bee algorithm (ABC), has been implemented for finding the optimal orientation of solar angle in analysing the performance. The result shows marginal differences are obtained in producing yearly maximum solar energy for different orientations of the PV module. It has been observed that the maximum average solar energy is obtained for the case where continuous adjustment is made by rotating the plane about the horizontal east-west axis within 20° to 30° tilt angle. The computed maximum and minimum of the monthly average efficiency is 10.9% and 8.7%, respectively. Further, a comparative study has been performed in generating average solar energy through optimal tilt angle by the implementation of Perturb & Observe method (P&O). The monthly average solar power computed by P&O method resulted better in a range of 2% to 15% in comparison to that obtained by ABC. While on the other hand, the efficiency computed by ABC algorithm was 15% to 19% better than that evaluated by P&O method for all the cases studied in the present work.

scholarly journals Measuring PV Module Performance at Different Tilt Angles in Southern Iraq Based Simulation

2018 ◽  
Vol 7 (2.34) ◽  
pp. 84
Author(s):  
Abadal Salam T. Hussain
Keyword(s):  
Tilt Angle ◽  
Solar Irradiance ◽  
Mathematical Equation ◽  
Pv Module ◽  
Yearly Maximum ◽  
Module Performance ◽  
The City ◽  
Southern Iraq

This paper presented that how to calculate the tilt angles and solar irradiance on photovoltaic (PV) module in southern Iraq (latitude 30° N). The latitude and day number of the city is taken into account to calculate the tilt angle and solar irradiance by using a mathematical equation. The optimum tilt angles of PV module in southern Iraq are range from 38° to 84°. The yearly maximum total and average solar irradiance is needed to determine the optimum tilt angle of PV module. The result shows that 50° of tilt angle is the best performance of PV module in southern Iraq.  

scholarly journals Evaluation of solar energy potential and PV module performance in the Gobi Desert of Mongolia

2006 ◽  
Vol 14 (6) ◽  
pp. 553-566 ◽  
Author(s):  
Amarbayar Adiyabat ◽  
Kosuke Kurokawa ◽  
Kenji Otani ◽  
Namjil Enebish ◽  
Garmaa Batsukh ◽  
...  
Keyword(s):  
Solar Energy ◽  
Gobi Desert ◽  
Energy Potential ◽  
Pv Module ◽  
Module Performance

Performance Analysis of Innovative Top Cooling Thermal Photovoltaic (TPV) Modules Under Tropics

2016 ◽  
Author(s):  
Swapnil Dubey ◽  
C. S. Soon ◽  
Sin Lih Chin ◽  
Leon Lee
Keyword(s):  
Solar Energy ◽  
Thermal Energy ◽  
Waste Heat ◽  
Heat Removal ◽  
Hot Water ◽  
Photovoltaic Module ◽  
Cell Temperature ◽  
Collector System ◽  
Pv Panel ◽  
Pv Module

The main focus area of this research paper to efficiently remove the heat generated during conversion of solar energy into electricity using photovoltaic (PV) module. The photovoltaic conversion efficiency of commercial available PV module varies in the range of 8%–20% depending on the type of solar cell materials used for the module construction, e.g. crystalline silicon, thin film, CIGS, organic, etc. During the conversion process, only a small fraction of the incident solar radiation is utilize by PV cells to produce electricity and the remaining is converted into waste heat in the module which causes the PV cell temperature to increase and its efficiency to drop. This thermal energy could be extract using air or water as a heat removal fluid to utilize in heating applications. The purpose of a solar photovoltaic module is to convert solar energy into electricity. The hybrid combination of photovoltaic module and thermal collector called Photovoltaic-thermal (PVT) module. Such PVT module combines a PV, which converts electromagnetic radiation (photons) into electricity, with a solar thermal module, which captures the remaining energy and removes waste heat from the PV module. Cooling of cells either by natural or forced circulation can reduce the PV cell temperature. The simultaneous cooling of the PV cells maintains their PV efficiency at a satisfactory level and offers a better way of utilizing solar energy by generating thermal energy as well. PVT system has higher overall efficiency as compared to separate PV and thermal collector. The heat output of a PVT module can be used for space heating or production of domestic hot water. This paper presents an innovative design of top cooling Thermal Photovoltaic (T-PV) module and its performance under outdoor weather condition of Singapore. T-PV collector is designed to flow fluid over the top of PV panel through a very narrow gap between the solar lens. This process improves heat removal process from PV panel, and hence, improves the electrical output of PV panel as compared to other PVT collector available in the market. By flowing the water from top of the PV panel will also provide better thermal efficiency. A T-PV collector system with storage tank, sensors, pump, flow meters, data logger and controls, have been installed at test-site located in Ngee Ann Polytechnic, Singapore. Performance analysis of T-PV collector system has been evaluated under the tropical climatic conditions of Singapore. It was found that T-PV module could produce additional electrical power as compared to standard PV panel of same capacity by operating at lower temperature. In addition to electricity, T-PV panel also generate the hot water up to 60 deg C at an average thermal efficiency of 41% for usage in residential and commercial buildings. The average thermal energy output was 3.1 kWh/day on typical day’s basis.

scholarly journals Impacts of Cloud Cover and Dust on the Performance of Photovoltaic Module in Niamey

2017 ◽  
Vol 2017 ◽  
pp. 1-8 ◽  
Author(s):  
Abdoulatif Bonkaney ◽  
Saïdou Madougou ◽  
Rabani Adamou
Keyword(s):  
Cloud Cover ◽  
Photovoltaic Module ◽  
Energy Yield ◽  
Solar Pv ◽  
Solar Module ◽  
Pv Module ◽  
Long Term Effect ◽  
Daily Energy ◽  
Dust Accumulation

The sensitivity of monocrystalline solar module towards dust accumulation and cloud cover is investigated from May to August 2015 for Niamey’s environment. Two solar modules with the same characteristics have been used to assess the impacts of the dust on the solar PV module. One of the modules is being cleaned every morning and the second one was used for monitoring the effect of dust accumulation onto the surface of the unclean module for May and June. Results show that dust accumulation has a great effect on decreasing the daily energy yield of the unclean module. But this effect is a long-term effect. For the cloud cover, the effect is immediate. It was estimated that exposing the module into the environment in 23 days in June 2015 has reduced the daily energy yield by 15.29%. This limitation makes solar PV an unreliable source of power for remote devices and thus strongly suggests the challenges of cleaning the module’s surface regularly.

scholarly journals Characterization Performance of Monocrystalline Silicon Photovoltaic Module Using Experimentally Measured Data

2019 ◽  
Vol 25 (10) ◽  
pp. 1-19
Author(s):  
Mena Safaa Mohammed ◽  
Emad Talib Hashim
Keyword(s):  
Ambient Temperature ◽  
Solar Irradiance ◽  
Clean Energy ◽  
Monocrystalline Silicon ◽  
Solar Irradiation ◽  
Weather Data ◽  
Photovoltaic Module ◽  
Solar Pv ◽  
Solar Module ◽  
Pv Module

Solar photovoltaic (PV) system has emerged as one of the most promising technology to generate clean energy. In this work, the performance of monocrystalline silicon photovoltaic module is studied through observing the effect of necessary parameters: solar irradiation and ambient temperature. The single diode model with series resistors is selected to find the characterization of current-voltage (I-V) and power-voltage (P-V) curves by determining the values of five parameters ( ). This model shows a high accuracy in modeling the solar PV module under various weather conditions. The modeling is simulated via using MATLAB/Simulink software. The performance of the selected solar PV module is tested experimentally for different weather data (solar irradiance and ambient temperature) that is gathered from October 2017 to April 2018 in the city of Baghdad. The collected data is recorded for the entire months during the time which is limited between 8:00 AM and 1:00 PM. This work demonstrates that the change in a cell temperature is directly proportional with the PV module current, while it is inversely proportional with the PV module voltage. Additionally, the output power of a PV module increases with decreasing the solar module temperature. Furthermore, the Simulink block diagram is used to evaluate the influence of weather factors on the PV module temperature by connecting to the MATLAB code. The best value from the results of this work was in March when the solar irradiance was equal to 1000 W/m2 and the results were: Isc,exp=3.015, Isc,mod=3.25 , RE=7.79 and Voc,exp=19.67 ,Voc,mod=19.9 ,RE=1.1

scholarly journals Performance analysis of thermosyphon hybrid photovoltaic thermal collector

2016 ◽  
Vol 27 (1) ◽  
pp. 28 ◽  
Author(s):  
N. Marc-Alain Mutombo ◽  
Freddie Inambao ◽  
Glen Bright
Keyword(s):  
Solar Irradiance ◽  
Rectangular Channel ◽  
Environmental Parameters ◽  
Photovoltaic Module ◽  
The Sun ◽  
Cell Temperature ◽  
Solar Module ◽  
Photovoltaic Modules ◽  
Pv Module ◽  
Incoming Energy

The conversion of solar irradiance into electricity by a photovoltaic module (PV) is 6– 7% of the incoming energy from the sun depending on the type of technology and the environmental parameters. More than 80% of incoming energy from the sun is reflected or absorbed by the solar module. The fraction of energy absorbed increases with solar cell temperature and the cells’ efficiency drops as a consequence. The efficiency of a PV module is improved by combining a PV module and a thermal collector in one unit, resulting in a hybrid photovoltaic and thermal collector (PV/T). The purpose of this paper is to present the behavior a thermosyphon hybrid PV/T when exposed to variations of environmental parameters and to demonstrate the advantage of cooling photovoltaic modules with water using a rectangular channel profile for the thermal collector. A single glazed flat-box absorber PV/T module was designed, its behavior for different environmental parameters tested, the numerical model developed, and the simulation for particular days for Durban weather run. The simulation result showed that the overall efficiency of the PV/T module was 38.7% against 14.6% for a standard PV module while the water temperature in the storage tank reached 37.1 °C. This is a great encouragement to the marketing of the PV/T technology in South Africa particularly during summer, and specifically in areas where the average annual solar irradiance is more than 4.70 kWh/m²/day.

scholarly journals Determining the Number of Solar Modules of a 1kW Solar Energy System in Antalya, Turkey

2018 ◽  
Vol 1 (1) ◽  
pp. 521-525
Author(s):  
Ceyda Aksoy Tırmıkçı ◽  
Cenk Yavuz
Keyword(s):  
Solar Radiation ◽  
Solar Energy ◽  
Tilt Angle ◽  
Energy System ◽  
Energy Output ◽  
Total Solar Radiation ◽  
Energy Relation ◽  
Solar Module ◽  
The City ◽  
Daily Total

In this paper the number of solar modules of a 1kW solar energy system was determined by using the total solar radiation and the solar module energy output energy relation. The total solar radiation was correlated with the tilt angle of solar modules. Thus the optimum yearly tilt angle of solar modules was calculated and assumed that solar modules of the system were tilted at this angle. In conclusion the monthly average daily total solar radiation, optimum yearly tilt angle and the number of solar modules of the related system were established for the city.

scholarly journals TEMPERATURE AND IRRADIANCE BASED ANALYSIS THE SPECIFIC VARIATION OF PV MODULE

2021 ◽  
Vol 83 (6) ◽  
pp. 1-17
Author(s):  
Mohsin Ali Koondhar ◽  
Irfan Ali Channa ◽  
Sadullah Chandio ◽  
Muhammad Ismail Jamali ◽  
Abdul Sami Channa ◽  
...  
Keyword(s):  
Iterative Methods ◽  
Standard Test ◽  
Operating Conditions ◽  
Back Surface ◽  
Photovoltaic Module ◽  
Solar Module ◽  
Pv Module ◽  
Test Conditions ◽  
Specific Variation ◽  
Module Efficiency

The effect of irradiance and increase of temperature on the back surface of the PV module would decrease the standardized efficiency of PV. To overcome this problem observed results of solar module (ORSM) and Newton Raphson’s (iterative) methods have been proposed in this research. This article compares ORSM and iterative methods of changing the specifications of a single diode model (SDM) extracted from a PV module beneath standard test conditions (STC) to calculate irradiance and various operating conditions. To make this comparison, the exact value of each diode parameter on the STC is essential. These are achieved by accepted algebraic values and iterative techniques. Newton Raphson’s technique has been proven to be the mainly precise method to find these specifications in STC. Therefore, these specifications are used to different techniques that change the parameters of an SDM with radiation and temperature. The MATLAB model is designed to assess the conducting of individual techniques by PVM. The results are compared with the measured data, and the accuracy of photovoltaic module efficiency has been achieved through different technologies at different temperature and insolation levels.

scholarly journals Experimental Testing of PV Module Performance

2021 ◽  
Vol 15 (1) ◽  
pp. 127-132
Author(s):  
Mladen Bošnjaković ◽  
Marinko Stojkov ◽  
Boris Zlatunić
Keyword(s):  
Tilt Angle ◽  
Experimental Testing ◽  
Measurement Methods ◽  
Clean Surface ◽  
Technical Data ◽  
Influence Of Temperature ◽  
Pv Panel ◽  
Pv Module ◽  
Pv Modules ◽  
Module Performance

This study compares the manufacturer's technical data of several PV modules with real measured outdoor technical data. The irradiance effect on several PV modules is examined by the changing a tilt angle and comparing different meteorological situations of sky clearness (clouds) on the modules mounted outdoor and exposed to Sun. Also, the influence of temperature and dust on the performance of a PV panel is under research using measurement methods described in the paper. The measured current and voltage data at the clean surface of the PV module correspond to the declared data of the PV module manufacturer, and in the case of fouling of the module surface with dust, a power drop of 7.39% was measured.

Effect of photovoltaic (PV) module mounting angle on PV module power output

2021 ◽  
Author(s):  
Husam Hamdi Alkhatib
Keyword(s):  
Solar Energy ◽  
Power Output ◽  
Alternative Energy ◽  
Fossil Fuels ◽  
Renewable Resource ◽  
Energy System ◽  
Photovoltaic Module ◽  
Energy Prices ◽  
Pv Module ◽  
Generating System

Solar energy is a renewable resource that is environmentally friendly. Unlike fossil fuels, solar energy is available just about everywhere on earth. This source of energy is free and immune to rising energy prices. Solar energy can be used in many ways - to provide electricity, heat, lighting, and mechanical power. The objective of this project is to determine the effect of mounting orientation of a photovoltaic panel on power output. Based on the simulation results, the report proposes alternative energy management techniques to characterize the unstable nature of the photovoltaic power generating system. A typical power generating system using photovoltaic technology would have many components. The software used for determining the effects of photovoltaic module mounting angle on the PV module power output is the PV-DesignPro. This software is designed to simulate photovoltaic energy system operation on an hourly basis for one year, based on a user selected climate and system design.

Sign in / Sign up

Export Citation Format

Share Document