scholarly journals Performance analysis of thermosyphon hybrid photovoltaic thermal collector

2016 ◽  
Vol 27 (1) ◽  
pp. 28 ◽  
Author(s):  
N. Marc-Alain Mutombo ◽  
Freddie Inambao ◽  
Glen Bright
Keyword(s):  
Solar Irradiance ◽  
Rectangular Channel ◽  
Environmental Parameters ◽  
Photovoltaic Module ◽  
The Sun ◽  
Cell Temperature ◽  
Solar Module ◽  
Photovoltaic Modules ◽  
Pv Module ◽  
Incoming Energy

The conversion of solar irradiance into electricity by a photovoltaic module (PV) is 6– 7% of the incoming energy from the sun depending on the type of technology and the environmental parameters. More than 80% of incoming energy from the sun is reflected or absorbed by the solar module. The fraction of energy absorbed increases with solar cell temperature and the cells’ efficiency drops as a consequence. The efficiency of a PV module is improved by combining a PV module and a thermal collector in one unit, resulting in a hybrid photovoltaic and thermal collector (PV/T). The purpose of this paper is to present the behavior a thermosyphon hybrid PV/T when exposed to variations of environmental parameters and to demonstrate the advantage of cooling photovoltaic modules with water using a rectangular channel profile for the thermal collector. A single glazed flat-box absorber PV/T module was designed, its behavior for different environmental parameters tested, the numerical model developed, and the simulation for particular days for Durban weather run. The simulation result showed that the overall efficiency of the PV/T module was 38.7% against 14.6% for a standard PV module while the water temperature in the storage tank reached 37.1 °C. This is a great encouragement to the marketing of the PV/T technology in South Africa particularly during summer, and specifically in areas where the average annual solar irradiance is more than 4.70 kWh/m²/day.

scholarly journals Characterization Performance of Monocrystalline Silicon Photovoltaic Module Using Experimentally Measured Data

2019 ◽  
Vol 25 (10) ◽  
pp. 1-19
Author(s):  
Mena Safaa Mohammed ◽  
Emad Talib Hashim
Keyword(s):  
Ambient Temperature ◽  
Solar Irradiance ◽  
Clean Energy ◽  
Monocrystalline Silicon ◽  
Solar Irradiation ◽  
Weather Data ◽  
Photovoltaic Module ◽  
Solar Pv ◽  
Solar Module ◽  
Pv Module

Solar photovoltaic (PV) system has emerged as one of the most promising technology to generate clean energy. In this work, the performance of monocrystalline silicon photovoltaic module is studied through observing the effect of necessary parameters: solar irradiation and ambient temperature. The single diode model with series resistors is selected to find the characterization of current-voltage (I-V) and power-voltage (P-V) curves by determining the values of five parameters ( ). This model shows a high accuracy in modeling the solar PV module under various weather conditions. The modeling is simulated via using MATLAB/Simulink software. The performance of the selected solar PV module is tested experimentally for different weather data (solar irradiance and ambient temperature) that is gathered from October 2017 to April 2018 in the city of Baghdad. The collected data is recorded for the entire months during the time which is limited between 8:00 AM and 1:00 PM. This work demonstrates that the change in a cell temperature is directly proportional with the PV module current, while it is inversely proportional with the PV module voltage. Additionally, the output power of a PV module increases with decreasing the solar module temperature. Furthermore, the Simulink block diagram is used to evaluate the influence of weather factors on the PV module temperature by connecting to the MATLAB code. The best value from the results of this work was in March when the solar irradiance was equal to 1000 W/m2 and the results were: Isc,exp=3.015, Isc,mod=3.25 , RE=7.79 and Voc,exp=19.67 ,Voc,mod=19.9 ,RE=1.1

scholarly journals Comparison of Performance Measurements of Photovoltaic Modules during Winter Months in Taxila, Pakistan

2014 ◽  
Vol 2014 ◽  
pp. 1-8 ◽  
Author(s):  
Muhammad Anser Bashir ◽  
Hafiz Muhammad Ali ◽  
Shahid Khalil ◽  
Muzaffar Ali ◽  
Aysha Maryam Siddiqui
Keyword(s):  
Solar Irradiance ◽  
Strong Dependence ◽  
Performance Ratio ◽  
Back Surface ◽  
Photovoltaic Module ◽  
Comparative Performance ◽  
Solar Module ◽  
Photovoltaic Modules ◽  
And Performance ◽  
Module Efficiency

This paper presents the comparative performance evaluation of three commercially available photovoltaic modules (monocrystalline, polycrystalline, and single junction amorphous silicon) in Taxila, Pakistan. The experimentation was carried out at outdoor conditions for winter months. Power output, module efficiency, and performance ratio were calculated for each module and the effect of module temperature and solar irradiance on these parameters was investigated. Module parameters showed strong dependence on the solar irradiance and module temperature. Monocrystalline and polycrystalline modules showed better performance in high irradiance condition whereas it decreased suddenly with decrease in irradiance. Amorphous solar module also showed good performance in low irradiance due to its better light absorbing characteristics and thus showed higher average performance ratio. Monocrystalline photovoltaic module showed higher monthly average module efficiency and was found to be more efficient at this site. Module efficiency and performance ratio showed a decreasing trend with increase of irradiance and photovoltaic module back surface temperature.

scholarly journals Experimental Application of Methods to Compute Solar Irradiance and Cell Temperature of Photovoltaic Modules

Sensors ◽  
2020 ◽  
Vol 20 (9) ◽  
pp. 2490
Author(s):  
Caio Felippe Abe ◽  
João Batista Dias ◽  
Gilles Notton ◽  
Ghjuvan Antone Faggianelli
Keyword(s):  
Solar Irradiance ◽  
Photovoltaic System ◽  
Photovoltaic Module ◽  
Electrical Measurements ◽  
Cell Temperature ◽  
Photovoltaic Modules ◽  
Order Of Magnitude ◽  
Simple Implementation ◽  
Temperature Levels ◽  
Mean Square Errors

Solar irradiance and cell temperature are the most significant aspects when assessing the production of a photovoltaic system. To avoid the need of specific sensors for quantifying such parameters, recent literature presents methods to estimate them through electrical measurements, using the photovoltaic module itself as a sensor. This work presents an application of such methods to data recorded using a research platform at University of Corsica, in France. The methods and the platform are briefly presented and the results are shown and discussed in terms of normalized mean absolute errors (nMAE) and root mean square errors (nRMSE) for various irradiance and cell temperature levels. The nMAE (and nRMSE) for solar irradiance are respectively between 3.5% and 3.9% (4.2% and 4.7%). Such errors on computed irradiance are in the same order of magnitude as those found in the literature, with a simple implementation. For cell temperatures estimation, the nMAE and nRMSE were found to be in the range 3.4%–8.2% and 4.3%–10.7%. These results show that using such methods could provide an estimation for the values of irradiance and cell temperature, even if the modules are not new and are not regularly cleaned, but of course not partially shaded.

scholarly journals Effect of Solar Tilt Angles on Photovoltaic Module Performance: A Behavioral Optimization Approach

2020 ◽  
pp. 90-102
Author(s):  
Trina Som ◽  
A. Sharma ◽  
D. Thakur
Keyword(s):  
Solar Energy ◽  
Tilt Angle ◽  
Photovoltaic Module ◽  
Optimization Approach ◽  
Solar Module ◽  
Monthly Average ◽  
Pv Module ◽  
Yearly Maximum ◽  
Module Performance ◽  
Better Than

In the present study, performance analyses of a solar module are made through the optimal variation of solar tilt angle, pertaining to the maximum generation of solar energy. The work has been carried out for a particular location at Tripura, in India, considering three different cases on an annual basis. An intelligent behavioural based algorithm, known as artificial bee algorithm (ABC), has been implemented for finding the optimal orientation of solar angle in analysing the performance. The result shows marginal differences are obtained in producing yearly maximum solar energy for different orientations of the PV module. It has been observed that the maximum average solar energy is obtained for the case where continuous adjustment is made by rotating the plane about the horizontal east-west axis within 20° to 30° tilt angle. The computed maximum and minimum of the monthly average efficiency is 10.9% and 8.7%, respectively. Further, a comparative study has been performed in generating average solar energy through optimal tilt angle by the implementation of Perturb & Observe method (P&O). The monthly average solar power computed by P&O method resulted better in a range of 2% to 15% in comparison to that obtained by ABC. While on the other hand, the efficiency computed by ABC algorithm was 15% to 19% better than that evaluated by P&O method for all the cases studied in the present work.

Development of a Thermal Model for Photovoltaic Modules and Analysis of NOCT Guidelines

2011 ◽  
Vol 134 (1) ◽  
Author(s):  
Ty W. Neises ◽  
Sanford A. Klein ◽  
Douglas T. Reindl
Keyword(s):  
Thermal Model ◽  
Photovoltaic Module ◽  
Cell Temperature ◽  
Flow Models ◽  
Photovoltaic Modules ◽  
Wind Speeds ◽  
Low Wind Speeds ◽  
Iec 61215 ◽  
Testing Standards ◽  
Operating Cell

The temperature of a photovoltaic module is typically required as an input to models that predict the module’s performance. Some common models use the nominal operating cell temperature (NOCT), as by the manufacturer. This paper develops a thermal model and uses it to analyze NOCT testing standards. Specifically, the standard correction factor charts found in the ASTM E1036 and IEC 61215 standards are evaluated. Results show that the correction charts were likely created assuming laminar flow correlations, while validation efforts and the fact that wind is often characterized by turbulence even at low wind speeds suggest that turbulent flow models may be more appropriate. In addition, the results presented in this paper show that the standard NOCT charts do not account for the backside insulation of photovoltaic (PV) arrays. These results suggest that the standard correction charts are inaccurate for any mounting types that differ from the open rack configuration. The paper concludes with recommendations to improve the usefulness of the NOCT.

Modelling and Simulation of Solar Photovoltaic Cell for Different Insolation Values Based on MATLAB/Simulink Environment

2014 ◽  
Vol 550 ◽  
pp. 137-143 ◽  
Author(s):  
S. Narendiran ◽  
Sarat Kumar Sahoo
Keyword(s):  
Photovoltaic Cell ◽  
Photovoltaic Module ◽  
Solar Photovoltaic ◽  
Electrical Characteristics ◽  
Array Type ◽  
Matlab Simulink ◽  
Photovoltaic Modules ◽  
Pv Module ◽  
Current Input ◽  
In Series

The paper discuss about the modelling and electrical characteristics of photovoltaic cell and its array type of construction in matlab-simulink environment at different insolation levels. The photovoltaic module is modelled using the diode electrical characteristic equation. The photovoltaic cell is analysed by voltage input and current input modules, The voltage and current input photovoltaic modules are simulated with different insolation values by varying the construction of PV modules. The results conclude that the current input PV module is well suited for applications were it shares same current when connected in series and voltage input PV module, where it shares same voltage when connected in parallel.

scholarly journals Analysis and Fabrication of an Active Cooling System for Reducing Photovoltaic Module Temperature

2017 ◽  
Vol 7 (5) ◽  
pp. 1980-1986
Author(s):  
A. Q. Jakhrani ◽  
A. R. Jatoi ◽  
S. H. Jakhrani
Keyword(s):  
Wind Speed ◽  
Flow Rate ◽  
Cooling System ◽  
Performance Comparison ◽  
Heat Extraction ◽  
Photovoltaic Module ◽  
Climatic Parameters ◽  
Photovoltaic Modules ◽  
Active Cooling ◽  
Pv Module

The purpose of this study is to fabricate and analyze an active cooling system for reducing photovoltaic (PV) module temperature and increasing its efficiency. An active cooling system was devised to cool the PV module. Two modules of same specifications were used for this study. One module was cooled, and other was left un-cooled for performance comparison. Solar radiations, wind speed, ambient temperature and temperatures at different points of the fabricated system were measured. The modules were mounted on a frame facing true south at the inclination of the latitude of the location. The measurements were taken during daytime with one hour intervals for two weeks. The temperatures at various points on cooled and un-cooled photovoltaic modules were noted using two different flow rates with 1 lit/min and 2 lit/min. It was discovered that the efficiency of PV module was enhanced from 6% to 7% during study period. The flow rate of 1lit/min was found more feasible for heat extraction as compared to the flow rate of 2lit/min. The wind speed was found to be more helpful for heat extraction from the modules as compared to other climatic parameters.

Performance Analysis of Innovative Top Cooling Thermal Photovoltaic (TPV) Modules Under Tropics

2016 ◽  
Author(s):  
Swapnil Dubey ◽  
C. S. Soon ◽  
Sin Lih Chin ◽  
Leon Lee
Keyword(s):  
Solar Energy ◽  
Thermal Energy ◽  
Waste Heat ◽  
Heat Removal ◽  
Hot Water ◽  
Photovoltaic Module ◽  
Cell Temperature ◽  
Collector System ◽  
Pv Panel ◽  
Pv Module

The main focus area of this research paper to efficiently remove the heat generated during conversion of solar energy into electricity using photovoltaic (PV) module. The photovoltaic conversion efficiency of commercial available PV module varies in the range of 8%–20% depending on the type of solar cell materials used for the module construction, e.g. crystalline silicon, thin film, CIGS, organic, etc. During the conversion process, only a small fraction of the incident solar radiation is utilize by PV cells to produce electricity and the remaining is converted into waste heat in the module which causes the PV cell temperature to increase and its efficiency to drop. This thermal energy could be extract using air or water as a heat removal fluid to utilize in heating applications. The purpose of a solar photovoltaic module is to convert solar energy into electricity. The hybrid combination of photovoltaic module and thermal collector called Photovoltaic-thermal (PVT) module. Such PVT module combines a PV, which converts electromagnetic radiation (photons) into electricity, with a solar thermal module, which captures the remaining energy and removes waste heat from the PV module. Cooling of cells either by natural or forced circulation can reduce the PV cell temperature. The simultaneous cooling of the PV cells maintains their PV efficiency at a satisfactory level and offers a better way of utilizing solar energy by generating thermal energy as well. PVT system has higher overall efficiency as compared to separate PV and thermal collector. The heat output of a PVT module can be used for space heating or production of domestic hot water. This paper presents an innovative design of top cooling Thermal Photovoltaic (T-PV) module and its performance under outdoor weather condition of Singapore. T-PV collector is designed to flow fluid over the top of PV panel through a very narrow gap between the solar lens. This process improves heat removal process from PV panel, and hence, improves the electrical output of PV panel as compared to other PVT collector available in the market. By flowing the water from top of the PV panel will also provide better thermal efficiency. A T-PV collector system with storage tank, sensors, pump, flow meters, data logger and controls, have been installed at test-site located in Ngee Ann Polytechnic, Singapore. Performance analysis of T-PV collector system has been evaluated under the tropical climatic conditions of Singapore. It was found that T-PV module could produce additional electrical power as compared to standard PV panel of same capacity by operating at lower temperature. In addition to electricity, T-PV panel also generate the hot water up to 60 deg C at an average thermal efficiency of 41% for usage in residential and commercial buildings. The average thermal energy output was 3.1 kWh/day on typical day’s basis.

scholarly journals Analysis of the cooling of PV modules with water on their efficiency

2020 ◽  
Vol 154 ◽  
pp. 05006
Author(s):  
Wojciech Luboń ◽  
Mirosław Janowski ◽  
Grzegorz Pełka ◽  
Paweł Reczek
Keyword(s):  
Solar Cells ◽  
Working Conditions ◽  
Water Film ◽  
Maximum Power ◽  
Cell Temperature ◽  
Photovoltaic Modules ◽  
Continuous Cooling ◽  
Pv Module ◽  
Pv Modules

The article presents the results of research on the efficiency of photovoltaic modules cooled by water. The purpose of the experiment was to improve the working conditions of the solar cells. Lowering the cell temperature increases the power generated by the device. The decrease in the temperature of the PV module was obtained by pouring water on the upper surface of the cells, as rain imitation or a water film. The power of the cooled and non-cooled devices were compared. The best results were achieved by cooling cells with a water film since there were no water splashes. The continuous cooling of cells surface causes a 20% increase of device's power. During the test, the non-cooled module reached the maximum power of 172 W, while the cooled one - 205 W. Cooling the module resulted in an increase in power by 33 W. In addition, the temperature of the cells dropped to almost 25°C. At this time, the temperature of the non-cooled module was 45°C. The presented solution may be an interesting proposition for small installations. The solution can also be an alternative for cleaning the modules due to the improvement in the power of the module after the test in terms of their power before.

scholarly journals Impacts of Cloud Cover and Dust on the Performance of Photovoltaic Module in Niamey

2017 ◽  
Vol 2017 ◽  
pp. 1-8 ◽  
Author(s):  
Abdoulatif Bonkaney ◽  
Saïdou Madougou ◽  
Rabani Adamou
Keyword(s):  
Cloud Cover ◽  
Photovoltaic Module ◽  
Energy Yield ◽  
Solar Pv ◽  
Solar Module ◽  
Pv Module ◽  
Long Term Effect ◽  
Daily Energy ◽  
Dust Accumulation

The sensitivity of monocrystalline solar module towards dust accumulation and cloud cover is investigated from May to August 2015 for Niamey’s environment. Two solar modules with the same characteristics have been used to assess the impacts of the dust on the solar PV module. One of the modules is being cleaned every morning and the second one was used for monitoring the effect of dust accumulation onto the surface of the unclean module for May and June. Results show that dust accumulation has a great effect on decreasing the daily energy yield of the unclean module. But this effect is a long-term effect. For the cloud cover, the effect is immediate. It was estimated that exposing the module into the environment in 23 days in June 2015 has reduced the daily energy yield by 15.29%. This limitation makes solar PV an unreliable source of power for remote devices and thus strongly suggests the challenges of cleaning the module’s surface regularly.

Sign in / Sign up

Export Citation Format

Share Document