Corrosion Process of Incoloy-800 in High Pressure and Temperature Aqueous Environment

2008 ◽  
Vol 59 (9) ◽  
Author(s):  
Dumitra Lucan ◽  
Manuela Fulger ◽  
Gheorghita Jinescu

The Steam Generators (SG), equipment that ensures the connection between the primary and secondary circuits, creates several safety problems during operation, mainly due to corrosion and mechanical damages. To provide information about the corrosion behaviour of the structural materials from CANDU SG under normal and abnormal conditions of operation and to identify the failure types produced by the corrosion were performed corrosion experiments consisting in chemical accelerated tests, static autoclaving and electrochemical methods. The gravimetric method, optical metallographic microscopy, XRD and EDS analysis, as well as electrochemical measurements have been used to evaluate the corrosion behavior of the steam generator tubes material (Incoloy-800).

Author(s):  
Mitch Hokazono ◽  
Clayton T. Smith

Integral light-water reactor designs propose the use of steam generators located within the reactor vessel. Steam generator tubes in these designs must withstand external pressure loadings to prevent buckling, which is affected by material strength, fabrication techniques, chemical environment and tube geometry. Experience with fired tube boilers has shown that buckling in boiler tubes is greatly alleviated by controlling ovality in bends when the tubes are fabricated. Light water reactor steam generator pressures will not cause a buckling problem in steam generators with reasonable fabrication limits on tube ovality and wall thinning. Utilizing existing Code rules, there is a significant design margin, even for the maximum differential pressure case. With reasonable bend design and fabrication limits the helical steam generator thermodynamic advantages can be realized without a buckling concern. This paper describes a theoretical methodology for determining allowable external pressure for steam generator tubes subject to tube ovality based on ASME Section III Code Case N-759-2 rules. A parametric study of the results of this methodology applied to an elliptical cross section with varying wall thicknesses, tube diameters, and ovality values is also presented.


RSC Advances ◽  
2018 ◽  
Vol 8 (9) ◽  
pp. 4671-4679
Author(s):  
Ruilin Xiong ◽  
Kui Xiao ◽  
Pan Yi ◽  
Yuting Hu ◽  
Chaofang Dong ◽  
...  

The effect of Bacillus subtilis (BS) on the corrosion behaviour of tin-coated copper was investigated by exposing the sample to a culture medium inoculated with BS.


Author(s):  
Lebe A. Nnanna ◽  
Wisdom O. John ◽  
Tochukwu E. Esihe ◽  
Kelechi C. Denkoro ◽  
Victor I. Okparaku ◽  
...  

Inhibition effect of Costusafer on mild steel in 0.5 M HCl was studied using gravimetric method at room temperature. It was found out that Costusafer inhibited the corrosion of mild steel in the acidic environment and that the efficiency of inhibition increased as the concentration of the inhibitor in the environment increased. The data was used to test different isotherms and it suited the Langmuir isotherm. A value of -15.995 kJmol-1 was gotten for the ∆Goads. This value showed that the extracts of Costusafer inhibited the corrosion process through physiosorption mechanism. The high value of inhibition efficiency of the extract as the concentration increased in rationalized in terms of the increase in herteroatoms, saponnins and tannins which are present in the extract.


1998 ◽  
Vol 40 (2-3) ◽  
pp. 401-410 ◽  
Author(s):  
R. Ramanauskas ◽  
L. Muleshkova ◽  
L. Maldonado ◽  
P. Dobrovolskis

Author(s):  
Hung Nguyen ◽  
Mark Brown ◽  
Shripad T. Revankar ◽  
Jovica Riznic

Steam generator tubes have a history of small cracks and even ruptures, which lead to a loss of coolant from the primary side to the secondary side. These tubes have an important role in reactor safety since they serve as one of the barriers between radioactive and non-radioactive materials of a nuclear power plant. A rupture then signifies the loss of the integrity of the tube itself. Therefore, choking flow plays an integral part not only in the engineered safeguards of a nuclear power plant, but also to everyday operation. There is limited data on actual steam generators tube wall cracks. Here experiments were conducted on choked flow of subcooled water through two samples of axial cracks of steam generator tubes taken from US PWR steam generators. The purpose of the experimental program was to develop database on critical flow through actual steam generator tube cracks with subcooled liquid flow at the entrance. The knowledge of this maximum flow rate through a crack in the steam generator tubes of a pressurized water nuclear reactor will allow designers to calculate leak rates and design inventory levels accordingly while limiting losses during loss of coolant accidents. The test facility design is modular so that various steam generator tube cracks can be studied. Two sets of PWR steam generators tubes were studied whose wall thickness is 1.285 mm. Tests were carried out at stagnation pressure up to 6.89 MPa and range of subcoolings 16.2–59°C. Based on these new choking flow data, the applicability of analytical models to highlight the importance of non-equilibrium effects was examined.


2021 ◽  
Vol 8 (1) ◽  
pp. 200639
Author(s):  
T. T. T. Tran ◽  
K. Kannoorpatti ◽  
A. Padovan ◽  
S. Thennadil

Sulfate-reducing bacteria (SRB) can regulate environmental pH because of their metabolism. Because local acidification results in pitting corrosion, the potential capacity of pH regulation by SRB would have important consequences for electrochemical aspects of the bio-corrosion process. This study focused on identifying the effect of pH on the corrosion of duplex stainless steel 2205 in a nutrient-rich artificial seawater medium containing SRB species, Desulfovibrio vulgaris . Duplex stainless steel samples were exposed to the medium for 13 days at 37°C at pH ranging from 4.0 to 7.4. The open-circuit potential value, sulfide level, pH and number of bacteria in the medium were recorded daily. Electrochemical impedance spectroscopy (EIS) and potentiodynamic polarization were used to study the properties of the biofilms at the end of the experiments and the corrosion behaviour of the material. Inductively coupled plasma mass spectrometry was used to measure the concentration of cations Fe, Ni, Mo, Mn, Cr in the experimental solution after 13 days. Scanning electron microscopy and energy-dispersive X-ray spectroscopy (EDX) were used for surface analysis. The results showed the pH changed from acidic values set at the beginning of the experiment to approximately pH 7.5 after 5 days owing to bacterial metabolism. After 13 days, the highest iron concentration was in the solution that was initially at pH 4 accompanied by pitting on the stainless steel. Sulfur was present on all specimens but with more sulfur at pH 4 in the EDX spectra. EIS showed the film resistance of the specimen at pH 4 was much lower than at pH 7.4 which suggests the corrosion resistance of the stainless steel was better at higher pH. The results of this study suggest that the corrosion process for the first few days exposure at low pH was driven by pH in solution rather than by bacteria. The increasing pH during the course of the experiment slowed down the corrosion process of materials originally at low pH. The nature and mechanism of SRB attack on duplex stainless steel at different acidic environments are discussed.


2019 ◽  
Vol 70 (8) ◽  
pp. 2968-2972
Author(s):  
Elena Ionela Neacsu ◽  
Virgil Constantin ◽  
Cristina Donath ◽  
Kazimir Yanushkevich ◽  
Aliona Zhivulka ◽  
...  

The corrosion behaviour of special alloys (Uranus B6 steel and Monel 400) exposed to chlorine chloride-deep eutectic solvents (DES) at 353 K has been investigated by polarization curves method. The corresponding corrosion parameters in choline chloride-oxalic acid and choline chloride-malonic acid were calculated. Micrographic images before and after immersion in the corrosive medium were obtained. Measurements of the influence of the corrosion process on the crystal structure and specific magnetization of the studied steels was carried out by using X-ray diffraction and respectivelly ponderomotive methods.


Sign in / Sign up

Export Citation Format

Share Document