scholarly journals To Calculation Of Bended Elements Working Under The Conditions Of Exposure To High And High Temperatures On The Lateral Force By A New Method

2021 ◽  
Vol 03 (05) ◽  
pp. 210-218
Author(s):  
Makhkamov Yuldashali Mamazhonovich ◽  
◽  
Mirzababayeva Sahiba Mirzaakbarovna ◽  
Keyword(s):  
Experimental Data ◽  
Reinforced Concrete ◽  
High Temperatures ◽  
Calculation Method ◽  
Lateral Force ◽  
New Method ◽  
Design Standards ◽  
Current Design ◽  
Calculation Results ◽  
Concrete Elements

The article presents a new method for calculating bending reinforced concrete elements made of conventional and heat-resistant concrete operating under conditions of high and high technological temperatures on the action of transverse forces. The advantage of the proposed calculation method over the method adopted in the current design standards based on a comparison of the calculation results of the experimental data is shown.

TO CALCULATION OF STEEL-REINFORCED CONCRETE RIBBED PLATES FOR REFURBISHED FLOORS

2021 ◽  
Vol 97 (5) ◽  
pp. 3-15
Author(s):  
F.S. ZAMALIEV ◽  
◽  
A.G. TAMRAZYAN ◽  
◽  
Keyword(s):  
Reinforced Concrete ◽  
Internal Stresses ◽  
Design Standards ◽  
Steel Reinforced Concrete ◽  
Economical Design ◽  
Bridge Structures ◽  
Composite Section ◽  
Current Design ◽  
Calculation Results ◽  
Concrete Elements

Analyzes national experience of restoring the old buildings floors. An assessment of the wood-reinforced concrete using experience, steel-reinforced concrete floor structures and methods for calculating load-bearing elements of a composite section is given. It is noted that the current design standards and existing methods for calculating steel-reinforced concrete structures of civil buildings and bridge structures use simplified calculation methods and do not reflect the actual stress-strain state of a bent element, do not take into account the initial pre-operational deformations and stresses, and do not lead to economical design solutions. Sometimes they lead to incorrect results. Expressions of internal moments and forces of steel-reinforced concrete bending elements are presented from the equilibrium conditions of a composite element, taking into account pre-operational forces. The results of our own experiments are presented, where it is shown that during the hardening of concrete, beams and slabs receive deformations in the form of reverse deflection (bending), and internal stresses arise in the sections of steel-reinforced concrete elements. Formulas are given for calculating the deflections of bending elements taking into account their initial deformations. To compare the calculation results of the proposed method for calculating steel-reinforced concrete elements, taking into account the initial deformations and stresses, the data of our own experiments were used and comparisons were given. Satisfactory convergence of the results is shown.

Proposals for Determining the Relative Deformations Design Value of εb3 Concrete in Volumetric Deformation Conditions

2021 ◽  
Vol 1043 ◽  
pp. 155-162
Author(s):  
Sergey Georgiev ◽  
Dmitriy Mailyan ◽  
Alik Blyagoz
Keyword(s):  
Experimental Data ◽  
Reinforced Concrete ◽  
Composite Materials ◽  
Transverse Direction ◽  
Calculation Methodology ◽  
Calculation Results ◽  
Russian Norms ◽  
Concrete Elements ◽  
Significant Underestimation ◽  
Composite Reinforcement

The article presents the studies’ results on the deformability and strength of reinforced concrete racks reinforced with composite materials with the characteristics stretching beyond the limits established by the norms of Russia, namely: the λh structures flexibility exceeding the value 15, the ratio of the cross-section sides equal to 1.5 and the eccentricity of the load application e0 exceeding 0.1h. The results of the tested racks calculations are analyzed according to BC 164.1325800.2014, which in some cases confirmed the inexpediency of using composite materials. However, according to the results of our experiment, an increase in the strength of a number of racks with the characteristics that go beyond the recommended standards was found. The purpose of this study is to check the methodology for calculating Russian norms for the compressed reinforced concrete elements, the parameters of which are outside the limits recommended by the norms, to develop proposals for improving the calculation based on the obtained experimental data and to determine the concrete deformability effect on the change in bearing capacity. The article discusses flexible struts, reinforced with composite materials, located in the transverse direction. The experimental data results on the deformability of concrete and the strength of struts reinforced in the transverse direction are presented. The calculation methodology, compiled in accordance with Russian standards, the calculation results of which are the theoretical values ​​of the deformability of concrete and the strength of the racks, is considered. After comparison, a significant underestimation of the theoretical strengths and a mismatch in the struts’ concrete deformations were revealed. It was found that the change in compressive deformations of concrete depends on the external composite reinforcement. Theoretical values , calculated according to the current standards, have significant discrepancies with the experimental ones. Based on the experiments’ results analysis, in the methodology of norms for calculating the ultimate compressive deformations of concrete the suggestions that take into account the type and percentage of composite reinforcement and ensure a good agreement between experimental and theoretical values have been made. After the introduction of the coefficient into normative calculation, new data on the theoretical strength of the struts were obtained, which showed significantly better convergence with the experimental data.

scholarly journals LATERAL FORCE PERCEIVED BY CONCRETE IN THE INCLINED SECTION OF REINFORCED CONCRETE ELEMENTS

2018 ◽  
Vol 15 (3) ◽  
pp. 434-444
Author(s):  
Y. V. Krasnoshchekov
Keyword(s):  
Reinforced Concrete ◽  
Lateral Force ◽  
Calculation Model ◽  
Shear Stresses ◽  
Empirical Dependence ◽  
Design Standards ◽  
Limit Value ◽  
Concrete Elements ◽  
Compression Resistance

Introduction. The article presents results of the empirical dependence analysis of transverse force in the inclined section of reinforced concrete elements.Materials and methods. Long-term application of such dependence at the reinforced concrete design demonstrates high parameters’ reliability. Thus, analyzed information could be used in innovated calculation model, which includes joint action of cross forces and bending moments.Results. The analysis of empirical dependence by the design standards seems to obtain information about the limit value of shear stresses in the compressed zone of inclined concrete and their interrelations with normal stresses. The results of the analysis were tested on computer models of the beam using finite elements. It does, however, assume that the shear resistance is specifically related to compression resistance by means of a special coefficient, which could be determined by computer simulation.Discussion and conclusions. The calculated values of the inclined section of reinforced concrete elements in the transverse bending could be specified by experimental or computer modeling.

SETTING A DIAGRAM APPROACH TO CALCULATING VIBRATED, CENTRIFUGED AND VIBROCENTRIFUGED REINFORCED CONCRETE COLUMNS WITH A VARIATROPIC STRUCTURE

2020 ◽  
pp. 22-34
Author(s):  
Л. Р. Маилян ◽  
С. А. Стельмах ◽  
Е. М. Щербань ◽  
М. П. Нажуев
Keyword(s):  
Experimental Data ◽  
Reinforced Concrete ◽  
Bearing Capacity ◽  
Cross Section ◽  
Concrete Columns ◽  
Reinforced Concrete Columns ◽  
The Cross ◽  
Concrete Elements ◽  
Diagram Approach

Состояние проблемы. Железобетонные элементы изготавливаются, как правило, по трем основным технологиям - вибрированием, центрифугированием и виброцентрифугированием. Однако все основные расчетные зависимости для определения их несущей способности выведены, исходя из основного постулата - постоянства и равенства характеристик бетона по сечению, что реализуется лишь в вибрированных колоннах. Результаты. В рамках диаграммного подхода предложены итерационный, приближенный и упрощенный способы расчета несущей способности железобетонных вибрированных, центрифугированных и виброцентрифугированных колонн. Выводы. Расчет по диаграммному подходу показал существенно более подходящую сходимость с опытными данными, чем расчет по методике норм, а также дал лучшие результаты при использовании дифференциальных характеристик бетона, чем при использовании интегральных и, тем более, нормативных характеристик бетона. Statement of the problem. Reinforced concrete elements are typically manufactured according to three basic technologies - vibration, centrifugation and vibrocentrifugation. However, all the basic calculated dependencies for determining their bearing capacity were derived using the main postulate, i.e., the constancy and equality of the characteristics of concrete over the cross section, which is implemented only in vibrated columns. Results. Within the framework of the diagrammatic approach, iterative, approximate and simplified methods of calculating the bearing capacity of reinforced concrete vibrated, centrifuged and vibrocentrifuged columns are proposed. Conclusions. The calculation according to the diagrammatic approach showed a significantly better convergence with the experimental data than that using the method of norms, and also performs better when using differential characteristics of concrete than when employing integral and particularly standard characteristics of concrete.

Tests on Mechanical Properties and Anti-Penetration Performance of Steel-Fiber Reactive Powder Concrete

2013 ◽  
Vol 671-674 ◽  
pp. 1761-1765
Author(s):  
Yong Liu ◽  
Chun Ming Song ◽  
Song Lin Yue
Keyword(s):  
Experimental Data ◽  
Mechanical Properties ◽  
Fracture Toughness ◽  
Compressive Strength ◽  
Reinforced Concrete ◽  
Steel Fiber ◽  
Reactive Powder Concrete ◽  
Calculation Results ◽  
Reactive Powder ◽  
Penetration Tests

In order to get mechanical properties ,some RPC samples with 5% steel fiber are tested, many groups data were obtained such as compressive strength, shear strength and fracture toughness. And a group of tests on RPC with 5% steel-fiber under penetration were also conducted to validate the performance to impact. The penetration tests are carried out by the semi-AP projectiles with the diameter of 57 mm and earth penetrators with the diameter of 80 mm, and velocities of the two kinds of projectiles are 300～600 m/s and 800～900 m/s, respectively. By contrast between the experimental data and the calculation results of C30 reinforced concrete by using experiential formula under penetration, it shows that the resistance of steel-fiber RPC to penetration is 3 times as that of general C30 reinforced concrete.

A Calculation Method to Investigate the Effects of Geometric Parameters and Operational Conditions on the Static Characteristics of Aerostatic Spherical Bearings

2018 ◽  
Vol 141 (2) ◽  
Author(s):  
Hailong Cui ◽  
Huan Xia ◽  
Dajiang Lei ◽  
Xinjiang Zhang ◽  
Zhengyi Jiang
Keyword(s):  
Experimental Data ◽  
Calculation Method ◽  
Reynolds Equation ◽  
Geometric Parameters ◽  
Static Characteristics ◽  
Optimal Parameters ◽  
Film Pressure ◽  
Operational Conditions ◽  
Pressure Distributions ◽  
Calculation Results

In this paper, a calculation method based on matlab partial differential equations (PDE) tool is proposed to investigate the static characteristics of aerostatic spherical bearings. The Reynolds equation of aerostatic spherical bearings is transformed into a standard elliptic equation. The effects of geometric parameters and operational conditions on the film pressure, bearing film force, and stiffness are studied. The axial and radial eccentricities result in different film pressure distributions; the bearing film force and stiffness are significantly influenced by geometric parameters and operational conditions. The relative optimal parameters are confirmed based on the calculation results. A comparison between the numerical and experimental results is also presented. The highest relative error between the numerical results and the experimental data is 11.3%; the calculation results show good agreements with the experimental data, thus verifying the accuracy of the calculation method used in this paper.

Bearing Capacity of Common and Damaged CFRP-Strengthened R. C. Beams Subject to High-Level Low-Cycle Loading

2019 ◽  
Vol 968 ◽  
pp. 185-199
Author(s):  
Vasyl M. Karpiuk ◽  
Yulia A. Syomina ◽  
Diana V. Antonova
Keyword(s):  
Bearing Capacity ◽  
Repeated Loading ◽  
Calculation Methods ◽  
Design Standards ◽  
Deformation Method ◽  
Current Design ◽  
Cycle Loading ◽  
High Level ◽  
Concrete Elements

In the course of operation or armed hostilities the span r.c. structures are subject to substantial damage and considerable reduction of their bearing capacity, especially under low-cycle repeated loading. In this connection it becomes necessary to renew their operation capacity and/or improve their bearing capacity. However, the current design standards contain no recommendations as to determination of the residual bearing capacity of such structures and calculation of their reinforcement. There are methods of the operation capacity renewal and reinforcement of the structures by increasing their sections adding metal or reinforced concrete elements. Still, the calculation methods of such reinforcement are also imperfect. It is proposed to renew operation capacity of such structures by strengthening their tensioned parts with CFRP; the performed experimental research will provide the basis for calculating bearing capacity of said structures with the aid of the deformation method improved by the authors.

scholarly journals Design Model Of Bending Reinforced Concrete Elements Under Action Of Transverse Forces Under Conditions Of Increased And High Temperatures

2020 ◽  
Vol 02 (10) ◽  
pp. 17-24
Author(s):  
Mahkamov Y.M. ◽  
Keyword(s):  
Reinforced Concrete ◽  
Crack Resistance ◽  
High Temperatures ◽  
Experimental Studies ◽  
Calculation Model ◽  
Design Model ◽  
Stress Strain ◽  
Concrete Elements

In this article, the calculation of the strength and crack resistance of bending elements operating under conditions of high and high temperatures and transverse forces are proposed to be carried out according to a calculation model developed based on an analysis of experimental studies that takes into account more correctly the physics of the stress-strain phenomenon of the element.

Strength of Normal and Inclined Sections of Bent Reinforced Concrete Elements with Zone Reinforcement Made of Steel Fiber

2022 ◽  
Vol 906 ◽  
pp. 7-15
Author(s):  
Dmitry Utkin
Keyword(s):  
Reinforced Concrete ◽  
Dynamic Loading ◽  
Calculation Method ◽  
Steel Fiber ◽  
Experimental Studies ◽  
Concrete Structures ◽  
Dynamic Loads ◽  
Reinforced Concrete Structures ◽  
Short Term ◽  
Concrete Elements

On the basis of theoretical and experimental studies, the prerequisites and the method of calculation of bent and compressed-curved reinforced concrete structures with zone reinforcement made of steel fiber, working under static and short-term dynamic loads, are formulated. In the developed method for calculating the strength of normal and inclined sections, a nonlinear deformation model is implemented, which is based on the actual deformation diagrams of materials. The developed calculation method is brought to the program of calculation of reinforced concrete structures with zone reinforcement of steel fiber under short-term dynamic loading, taking into account the inelastic properties of materials. The numerical studies made it possible to determine the influence of various parameters of steel-fiber reinforcement on the strength of reinforced concrete elements. To confirm the main results of the developed calculation method, experimental studies of reinforced concrete beam structures reinforced with conventional reinforcement and a zone steel-fiber layer are planned and carried out. Experimental studies were carried out under static and short-term dynamic loads. As a result of the conducted experiments, data were obtained that characterize the process of destruction, deformation and cracking of steel-reinforced concrete elements under such types of loading. The dependences of changes in the energy intensity of reinforced concrete structures with zone reinforcement made of steel fiber in the compressed and stretched cross-section zones under dynamic loading are obtained. The effectiveness of the use of fiber reinforcement of normal and inclined sections of bent and compressed-curved elements to improve the strength and deformative.

Sign in / Sign up

Export Citation Format

Share Document