scholarly journals The investigation on the AC to DC voltage multiplier

2021 ◽  
Vol 2 (4) ◽  
Author(s):  
Taige Chen
Keyword(s):  
Output Voltage ◽  
Input Voltage ◽  
Voltage Source ◽  
Input Frequency ◽  
Dc Voltage ◽  
Voltage Multiplier ◽  
Voltage Doubler

This paper investigates the topic of voltage multiplication, which converts a low AC voltage source to a high DC voltage source. Several designs are evaluated, such as the voltage doubler, the voltage tripler, and the voltage quadrupler. It is discovered that the input frequency and the capacitance do not affect the output voltage. This design can be extended to any integer multiples of the input voltage.

scholarly journals Implementasi DC-DC Boost Converter Menggunakan Arduino Berbasis Simulink Matlab

2020 ◽  
Vol 1 (2) ◽  
pp. 144-149
Author(s):  
Muldi Yuhendri ◽  
Randy Setiawan
Keyword(s):  
Direct Current ◽  
Output Voltage ◽  
Input Voltage ◽  
Voltage Regulation ◽  
Power Converter ◽  
Boost Converter ◽  
Experimental Results ◽  
Voltage Source ◽  
Matlab Simulink ◽  
Dc Voltage

Direct current (dc) voltage sources are one of the voltage sources most widely used for various purposes. Dc voltage can be obtained from a dc generator or by converting an ac voltage into a dc voltage using a power converter. There are several dc voltage levels that are commonly used by electrical and electronic equipment. To get a dc voltage that can be used for various equipment, then a dc voltage source must be varied according to the required. One way to get a variable dc voltage is to use a dc-dc converter. This research proposes a dc-dc boost converter that can increase the dc voltage with varying outputs. The boost converter is proposed using Arduino Uno as a controller with an input voltage of 12 volts. The converter output voltage regulation is implemented through Arduino programming using Matlab simulink. The experimental results show that the boost converter designed in this study has worked well as intended. This can be seen from the boost converter output voltage which is in accordance with the reference voltage entered in the Matlab simulink program

scholarly journals An Eleven-Level Switched-Capacitor Inverter with Boosting Capability

Electronics ◽  
2021 ◽  
Vol 10 (18) ◽  
pp. 2262
Author(s):  
Md Reyaz Hussan ◽  
Adil Sarwar ◽  
Irfan Khan ◽  
Mohd Tariq ◽  
Mohammad Tayyab ◽  
...  
Keyword(s):  
Output Voltage ◽  
Detailed Comparison ◽  
Input Voltage ◽  
Voltage Source ◽  
Switched Capacitor ◽  
Level Control ◽  
Voltage Waveform ◽  
Dc Voltage ◽  
Bidirectional Switches ◽  
State Of Art

An 11-level switched-capacitor multilevel inverter (SCMLI) with 2.5 times boosting feature is presented in this paper. It can produce an 11-level output voltage waveform by utilizing 14 switches, 3 capacitors, 2 diodes, and 1 DC source. Only nine driver circuits are needed as the topology has three pairs of complementary switches and two bidirectional switches. It has inherent capacitor self-balancing property as the capacitors are connected across the DC voltage source during several states within a fundamental cycle to charge the capacitors to the input voltage. A detailed comparison shows the effectiveness of the proposed topology in terms of the number of switches, number of capacitors, number of sources, total standing voltage (TSV), efficiency, and boosting ability with the state-of-art recently proposed circuits. Subsequently, the performance of the proposed SCMLI is validated experimentally utilizing the nearest level control (NLC), a fundamental frequency-based switching technique.

scholarly journals Kendali Tegangan Output Buck Converter Menggunakan Arduino Berbasis Simulink Matlab

2021 ◽  
Vol 2 (1) ◽  
pp. 34-39
Author(s):  
Ari Anggawan ◽  
Muldi Yuhendri
Keyword(s):  
Direct Current ◽  
Output Voltage ◽  
Rapid Development ◽  
Input Voltage ◽  
Voltage Regulation ◽  
Buck Converter ◽  
Electronic Equipment ◽  
Voltage Source ◽  
Dc Voltage ◽  
Direct Voltage

The rapid development of technology to date has made many electrical and electronic equipment that require a direct current (dc) voltage source whose output voltage can be adjusted to the needs of the user. There are several direct voltage levels that are commonly used by electrical and electronic equipment. To get a direct voltage that can be used for various equipment, a direct voltage source that can be varied according to need is required. One way to convert a dc voltage source to a lower dc voltage source is by using a buck converter circuit. This study proposes a buck type direct current converter is porposed to use the Arduino uno as a PWM signal generator circuit to control to control the 24 volt input voltage. The converter output voltage regulation is implemented through a potentiometer and Arduino programming using the simulink Matlab. In this research, a buck converter is tested with output voltage feedback so that the output voltage remains stable. The result of the test that have been carried out show that the buck converter designed in this study has worked well in accordance with objectives. This can be seen from the buck converter output voltage that is in accordance with the reference voltage using a potentiometer that is included in the simulink Matlab program.  

scholarly journals Pengendalian Tegangan Keluaran DC-DC Boost Converter Tipe Voltage Doubler Menggunakan Mikrokontroler STM32F1038CT

2020 ◽  
Vol 12 (2) ◽  
pp. 40-46
Author(s):  
Kevin Candra ◽  
Leonardus Heru Pratomo
Keyword(s):  
Output Voltage ◽  
Pulse Width Modulation ◽  
Control Method ◽  
Computational Simulation ◽  
Industrial Applications ◽  
Boost Converter ◽  
Voltage Source ◽  
Dc Voltage ◽  
Voltage Doubler ◽  
Electric Motor Drive

Five-level inverter is widely used in many industrial applications, for example as a three-phase electric motor drive, PLTS, etc. This inverter works using two separated DC voltage sources in order to form different voltage level. Five-level inverter using one DC voltage source will be more efficient. A DC-DC boost converter on Voltage Doubler type is used in order to solve the problem. The focus of this research is on controlling the DC-DC boost converter on Voltage Doubler type. The switch control method uses a shifted pulse width modulation of 1800. To get a suitable output voltage, an output voltage control system is applied. A proportional and integral type control is implemented using STM32F1038CT microcontroller.  The output voltage controlled DC-DC boost converter is validated through computational simulation with Power Simulator software and as the final step will be implemented on hardware in the laboratory. Based on the simulation and implementation, Voltage-Doubler type of DC-DC boost converter is able to produce the required output voltage, which is two times greater than the conventional DC-DC boost converter output voltage.

scholarly journals An Asymmetrical Step-Up Multilevel Inverter Based on Switched-Capacitor Network

2019 ◽  
Vol 11 (12) ◽  
pp. 3453 ◽  
Author(s):  
Taghvaie ◽  
Alijani ◽  
Adabi ◽  
Rezanejad ◽  
Adabi ◽  
...  
Keyword(s):  
Input Voltage ◽  
Multilevel Inverter ◽  
Voltage Source ◽  
Switched Capacitor ◽  
Voltage Waveform ◽  
Dc Voltage ◽  
Magnetic Elements ◽  
High Level ◽  
Control Implementation

This paper presents a transformerless step-up multilevel inverter based on a switched-capacitor structure. One of the main contributions of the proposed topology is replacing the separated DC voltage source with capacitors which are charged at predetermined time intervals. Therefore, a high-level staircase voltage waveform can be achieved by discharging some of these capacitors on the load. The other contribution of the proposed structure is to eliminate the magnetic elements which traditionally boost the input DC voltage. In addition, asymmetrical or unequal amounts of capacitor voltages create more voltage levels, which enable voltage level increments without increasing the number of semiconductor devices. This paper introduces a self-balanced boost Switched-Capacitors Multilevel Inverter (SCMLI) which is able to create a nearly sinusoidal voltage waveform with a maximum voltage of up to 45 times that of the input voltage DC source. Higher level output voltage levels are also achievable by extending the circuit topology. After determination of the switching angles and selecting the proper switching states for each level, an offline NLC method is used for modulation, which eases the control implementation. Analysis, simulation and experiments are carried out for a 91-level inverter (45 levels for positive and negative voltages and one for zero voltage) are presented.

scholarly journals Development of a New Cascade Voltage-Doubler for Voltage Multiplication

2014 ◽  
Vol 2014 ◽  
pp. 1-6 ◽  
Author(s):  
Arash Toudeshki ◽  
Norman Mariun ◽  
Hashim Hizam ◽  
Noor Izzri Abdul Wahab
Keyword(s):  
Output Voltage ◽  
Input Voltage ◽  
Output Quality ◽  
Voltage Doubler ◽  
Circuit Configuration

For more than eight decades, cascade voltage-doubler circuits are used as a method to produce DC output voltage higher than the input voltage. In this paper, the topological developments of cascade voltage-doublers are reviewed. A new circuit configuration for cascade voltage-doubler is presented. This circuit can produce a higher value of the DC output voltage and better output quality compared to the conventional cascade voltage-doubler circuits, with the same number of stages.

scholarly journals Design of Single Inductor and Two Output DC - DC Converter

2020 ◽  
pp. 54-59
Author(s):  
S. Inbasakaran ◽  
Mahesh. K ◽  
Lithesh. J
Keyword(s):  
Output Voltage ◽  
Input Voltage ◽  
Power Supplies ◽  
Electronic Systems ◽  
Minimum Loss ◽  
Voltage Level ◽  
Dc Voltage ◽  
Electronic Circuitry ◽  
Dc Power ◽  
Common Goals

<p>A DC-DC converter is used to convert from one DC voltage level to another DC voltage level. The output voltage may be increased or decreased when compare to the input voltage based on the circuit topology. DC – DC converters are mainly used as a regulated and isolated power supplies in many applications. Regulated dc power supplies are needed for most analog and digital electronic systems. Most power supplies are designed to meet some or all of the following requirements:</p> <p><strong>Regulated output: </strong>The output voltage must be kept constant with respect to the change in output loading.</p> <p><strong>Isolation: </strong>The output may be required to be electrically isolated from the input.</p> <p>In addition to these requirements, common goals are to reduce power supply size and weight and improve their efficiency. A few applications of DC-DC converters are where 5V DC on a personal computer motherboard must be stepped down to 3V, 2V or less for one of the latest CPU chips; where 1.5V from a single cell must be stepped up to 5V or more, to operate electronic circuitry. The main focus in this paper is to generate dc voltage from a one level to other level with minimum loss. The need for such converters has risen due to the fact that transformers are unable to function on dc.</p>

scholarly journals A 13-Level Asymmetrical Cascaded Inverter for Photovoltaic System With DC-DC Flyback Converter

2019 ◽  
Vol 8 (3) ◽  
pp. 6584-6591
Keyword(s):  
Output Voltage ◽  
Harmonic Distortion ◽  
Photovoltaic Cell ◽  
Multilevel Inverter ◽  
Photovoltaic System ◽  
Solar Irradiation ◽  
Voltage Source ◽  
Asymmetric Mode ◽  
Dc Voltage ◽  
Point Tracking

In recent days, multilevel inverter has widely been used for high power application. This may be due to the reduction of total harmonic distortion (THD) of the output voltage level and having low blocking voltages of switches. In the existing system, DC voltage source which is maintained constant is given as the input to the inverters which contains the series connection of fundamental block and is analyzed in symmetric and asymmetric mode of operation to produce various voltage levels. The proposed approach replaces the DC voltage source to the Photovoltaic (PV) cell has been used which has variations in the output voltage side depends on the solar irradiation level. This Photovoltaic cell uses Maximum Power Point Tracking (MPPT) algorithm to produce required voltage. As the input to the multilevel inverter (MLI) has to be maintained constant a fly back forward converter has been used in between the Photovoltaic cell and the multilevel inverter, so that the required multiple constant output voltage has been obtained on the output of the converter. Using the output of the converter 13 output voltage levels can be obtained from the multilevel inverter. The performance of the proposed system is verified by simulation through MATLAB/Simulink environment

scholarly journals The Design of DC 12 V to DC 380 V 1000 Watt Converter with ATmega328 as a 65 KHz Oscillator

2020 ◽  
Vol 2 (2) ◽  
pp. 139-148
Author(s):  
Kurnia Brahmana
Keyword(s):  
Oscillation Frequency ◽  
Output Voltage ◽  
Input Voltage ◽  
Voltage Source ◽  
Test Results

A DC to DC converter has been built and research has been conducted to examine the effect of load on the output voltage of the DC to DC converter with fixed oscillation frequency. This converter DC to DC circuit uses a 12 V DC battery as an input voltage source connected with a step-up transformer until it is successfully raised to 380 V DC. The load given to the DC to DC circuit converter in the form of lamps, varies from 40 watts to 960 watts with a fixed oscillation frequency of 65 Khz that has been determined by the microcontroller. The test results showed that the output voltage value decreased in accordance with the increase in load so that when the load of 960 watts obtained the output voltage of 220 V DC.

A Single-Stage Square Wave Buck-Boost Inverter

2015 ◽  
Vol 793 ◽  
pp. 280-285
Author(s):  
J.A. Soo ◽  
N.A. Rahman ◽  
J.H. Leong
Keyword(s):  
Duty Cycle ◽  
Output Voltage ◽  
Boost Converter ◽  
Single Stage ◽  
Experimental Results ◽  
Voltage Source ◽  
Voltage Waveform ◽  
Boost Converters ◽  
Dc Voltage ◽  
Square Wave

This paper proposed a novel single-stage square wave buck-boost inverter (SWBBI). The proposed inverter is designed by using dual buck-boost converters. The input DC voltage of the proposed inverter can be either stepped-down or stepped-up in square output voltage waveform depending on the duty-cycle applied for each buck-boost converter. This characteristic is not found in conventional voltage source inverter where the output voltage is always lower than the input DC voltage. The proposed inverter is analyzed by a series of simulations using MATLAB/Simulink as well as experiments by using different values of duty-cycle. A conclusion about the feasibility of the proposed inverter is given by comparing the simulation and experimental results.

Sign in / Sign up

Export Citation Format

Share Document