scholarly journals Implementasi DC-DC Boost Converter Menggunakan Arduino Berbasis Simulink Matlab

2020 ◽  
Vol 1 (2) ◽  
pp. 144-149
Author(s):  
Muldi Yuhendri ◽  
Randy Setiawan
Keyword(s):  
Direct Current ◽  
Output Voltage ◽  
Input Voltage ◽  
Voltage Regulation ◽  
Power Converter ◽  
Boost Converter ◽  
Experimental Results ◽  
Voltage Source ◽  
Matlab Simulink ◽  
Dc Voltage

Direct current (dc) voltage sources are one of the voltage sources most widely used for various purposes. Dc voltage can be obtained from a dc generator or by converting an ac voltage into a dc voltage using a power converter. There are several dc voltage levels that are commonly used by electrical and electronic equipment. To get a dc voltage that can be used for various equipment, then a dc voltage source must be varied according to the required. One way to get a variable dc voltage is to use a dc-dc converter. This research proposes a dc-dc boost converter that can increase the dc voltage with varying outputs. The boost converter is proposed using Arduino Uno as a controller with an input voltage of 12 volts. The converter output voltage regulation is implemented through Arduino programming using Matlab simulink. The experimental results show that the boost converter designed in this study has worked well as intended. This can be seen from the boost converter output voltage which is in accordance with the reference voltage entered in the Matlab simulink program

scholarly journals Kendali Tegangan Output Buck Converter Menggunakan Arduino Berbasis Simulink Matlab

2021 ◽  
Vol 2 (1) ◽  
pp. 34-39
Author(s):  
Ari Anggawan ◽  
Muldi Yuhendri
Keyword(s):  
Direct Current ◽  
Output Voltage ◽  
Rapid Development ◽  
Input Voltage ◽  
Voltage Regulation ◽  
Buck Converter ◽  
Electronic Equipment ◽  
Voltage Source ◽  
Dc Voltage ◽  
Direct Voltage

The rapid development of technology to date has made many electrical and electronic equipment that require a direct current (dc) voltage source whose output voltage can be adjusted to the needs of the user. There are several direct voltage levels that are commonly used by electrical and electronic equipment. To get a direct voltage that can be used for various equipment, a direct voltage source that can be varied according to need is required. One way to convert a dc voltage source to a lower dc voltage source is by using a buck converter circuit. This study proposes a buck type direct current converter is porposed to use the Arduino uno as a PWM signal generator circuit to control to control the 24 volt input voltage. The converter output voltage regulation is implemented through a potentiometer and Arduino programming using the simulink Matlab. In this research, a buck converter is tested with output voltage feedback so that the output voltage remains stable. The result of the test that have been carried out show that the buck converter designed in this study has worked well in accordance with objectives. This can be seen from the buck converter output voltage that is in accordance with the reference voltage using a potentiometer that is included in the simulink Matlab program.  

A Single-Stage Square Wave Buck-Boost Inverter

2015 ◽  
Vol 793 ◽  
pp. 280-285
Author(s):  
J.A. Soo ◽  
N.A. Rahman ◽  
J.H. Leong
Keyword(s):  
Duty Cycle ◽  
Output Voltage ◽  
Boost Converter ◽  
Single Stage ◽  
Experimental Results ◽  
Voltage Source ◽  
Voltage Waveform ◽  
Boost Converters ◽  
Dc Voltage ◽  
Square Wave

This paper proposed a novel single-stage square wave buck-boost inverter (SWBBI). The proposed inverter is designed by using dual buck-boost converters. The input DC voltage of the proposed inverter can be either stepped-down or stepped-up in square output voltage waveform depending on the duty-cycle applied for each buck-boost converter. This characteristic is not found in conventional voltage source inverter where the output voltage is always lower than the input DC voltage. The proposed inverter is analyzed by a series of simulations using MATLAB/Simulink as well as experiments by using different values of duty-cycle. A conclusion about the feasibility of the proposed inverter is given by comparing the simulation and experimental results.

scholarly journals The investigation on the AC to DC voltage multiplier

2021 ◽  
Vol 2 (4) ◽  
Author(s):  
Taige Chen
Keyword(s):  
Output Voltage ◽  
Input Voltage ◽  
Voltage Source ◽  
Input Frequency ◽  
Dc Voltage ◽  
Voltage Multiplier ◽  
Voltage Doubler

This paper investigates the topic of voltage multiplication, which converts a low AC voltage source to a high DC voltage source. Several designs are evaluated, such as the voltage doubler, the voltage tripler, and the voltage quadrupler. It is discovered that the input frequency and the capacitance do not affect the output voltage. This design can be extended to any integer multiples of the input voltage.

scholarly journals An Overview on Problem of Balancing Of DC Capacitor Voltage in Diode-Clamped Multilevel Inverter Using Boost Converter

10.29007/m2mq ◽  
2018 ◽  
Author(s):  
Shubham R. Patel ◽  
Gaurang K. Sharma ◽  
Ashish R. Patel
Keyword(s):  
High Voltage ◽  
Output Voltage ◽  
Harmonic Distortion ◽  
Load Condition ◽  
Boost Converter ◽  
Multilevel Inverter ◽  
Matlab Simulink ◽  
Dc Voltage ◽  
Voltage Output ◽  
Capacitor Voltage

Multilevel inverter allows the production of high voltage with lower harmonic distortion in ac output and it eliminates the need of transformer. With the usage of multilevel inverter, we can get the required ac voltage output from multiple dc voltage rails. One of the disadvantage in it is the unbalancing of dc link capacitor voltage. The basic aim of this paper is the balancing of dc link capacitor voltage in diode-clamped multilevel inverter. There are different approaches which could be used for balancing of the capacitor voltage. In this paper, the method of additional auxiliary circuit in the form of Two-level Boost converter is being adopted to balance the inner capacitor voltages so as to get the required multilevel output. This balancing leads to the reliability in the inverter output voltage and extension in life of capacitor. The simulations for this are being performed in MATLAB SIMULINK® and the result are being analyzed for the same by employing it for different load condition. The scheme thus offer the proper balancing of capacitor voltage.

scholarly journals Modified PMSG System using Trans Z Source Network for Grid Connected UPFC System

2019 ◽  
Vol 9 (2) ◽  
pp. 4107-4111
Keyword(s):  
Wind Power ◽  
Input Voltage ◽  
Voltage Regulation ◽  
Boost Converter ◽  
Power Network ◽  
Dc Voltage ◽  
Source Voltage

This paper presents a grid connected UPFC system for PMSG wind power network using a Trans Zsource converter. The Trans Z-source converter has a common stage buck boost converter to produce DC voltage from AC input voltage by stabilizing the shoot through state. In the proposed system, the changing in shoot-through state is used to keep trans Z-source voltage regulation with respect to d-q current is capable to take out the more power from the turbine (wind) and fed to grid. The proposed system with UPFC has higherefficiency performanceand cost effectivecompare with conventional Z source PMSG based UPFC system. Matlab simulations are carried out and results prove that proposed system is better.

scholarly journals Rancang Bangun Multilevel Boost Converter Untuk Catu Daya Motor Arus Searah Pada Kendaraan Listrik Berbasis Mikrokontroler

Electrician ◽  
2018 ◽  
Vol 12 (3) ◽  
pp. 111
Author(s):  
Noer Soedjarwanto ◽  
Endah Komalasari ◽  
Venus Asadila
Keyword(s):  
Electric Vehicles ◽  
Direct Current ◽  
Duty Cycle ◽  
Power Supply ◽  
Rotational Speed ◽  
Output Voltage ◽  
Input Voltage ◽  
Boost Converter ◽  
Working Principle ◽  
Converter Testing

Abstrak— Rangkaian multilevel boost converter memiliki prinsip kerja yang sama dengan boost converter konvensional namun rasio tegangan keluarannya lebih tinggi. Dimana tegangan keluaran dari multilevel boost converter ini akan digunakan sebagai catu daya untuk mengendalikan kecepatan putar motor arus searah (MAS). Kemudian akan dilakukan perbandingan antara tegangan keluaran multilevel boost converter dengan boost converter konvensional yang digunakan sebagai catu daya MAS. Pada penelitian ini nilai tegangan keluaran multilevel boost converter saat dihubungkan pada MAS dengan duty cycle 20% yaitu 80,3 volt dan MAS sudah mulai berputar dengan kecepatan 350 rpm. Sementara tegangan keluaran boost converter konvensional sebesar 39,4 volt namun MAS belum dapat berputar pada duty cycle 20% dan tegangan masukan yang sama yaitu 12,3 volt. Kemudian dilakukan penambahan beban MAS pada pengujian multilevel boost converter. Dimana semakin berat beban pada MAS maka torsinya akan meningkat. Dengan demikian perangkat multilevel boost converter dapat digunakan sebagai catu daya MAS untuk kendaraan listrik. Kata kunci: Multilevel boost converter, boost converter, motor arus searah Abstract—Multilevel boost converter circuit has the same working principle with conventional boost converter. Hence, the ratio of its output voltage is higher that will be used as power supply for controlling the rotational speed of MAS. Then, there will be comparison among the output voltage of multilevel boost converter and conventional boost converter which will be used as power supply of MAS. On this research, the output voltage value of multilevel boost converter which is connected with MAS at the duty cycle 20 % is 80,3 volt. Furthermore, it had rotated at the speed of 320 rpm. Meanwhile, the output voltage of boost converter conventional is 39,4 volt. On the contrary, MAS can not rotated at the duty cycle of 20 % with the same input voltage that will be 12,3 volt. Then, it will be added with load of MAS for multilevel boost converter testing. While the load of MAS is heavier, its torque will be increased too. Therefore, multilevel boost converter device can be used as power supply of MAS for electric vehicles. Keywords: Multilevel boost converter, boost converter, direct current motor

scholarly journals An Eleven-Level Switched-Capacitor Inverter with Boosting Capability

Electronics ◽  
2021 ◽  
Vol 10 (18) ◽  
pp. 2262
Author(s):  
Md Reyaz Hussan ◽  
Adil Sarwar ◽  
Irfan Khan ◽  
Mohd Tariq ◽  
Mohammad Tayyab ◽  
...  
Keyword(s):  
Output Voltage ◽  
Detailed Comparison ◽  
Input Voltage ◽  
Voltage Source ◽  
Switched Capacitor ◽  
Level Control ◽  
Voltage Waveform ◽  
Dc Voltage ◽  
Bidirectional Switches ◽  
State Of Art

An 11-level switched-capacitor multilevel inverter (SCMLI) with 2.5 times boosting feature is presented in this paper. It can produce an 11-level output voltage waveform by utilizing 14 switches, 3 capacitors, 2 diodes, and 1 DC source. Only nine driver circuits are needed as the topology has three pairs of complementary switches and two bidirectional switches. It has inherent capacitor self-balancing property as the capacitors are connected across the DC voltage source during several states within a fundamental cycle to charge the capacitors to the input voltage. A detailed comparison shows the effectiveness of the proposed topology in terms of the number of switches, number of capacitors, number of sources, total standing voltage (TSV), efficiency, and boosting ability with the state-of-art recently proposed circuits. Subsequently, the performance of the proposed SCMLI is validated experimentally utilizing the nearest level control (NLC), a fundamental frequency-based switching technique.

scholarly journals Power applications for fuel-cell using switching regulators

2019 ◽  
Vol 15 (1) ◽  
pp. 71
Author(s):  
Dega Rajaji Vanka ◽  
K. Chandra Sekhar
Keyword(s):  
Fuel Cell ◽  
Output Voltage ◽  
Closed Loop ◽  
Control Method ◽  
Voltage Regulation ◽  
Boost Converter ◽  
System Stability ◽  
Voltage Source ◽  
Energy Unit ◽  
Fuel Cell Stack

<p><strong> </strong></p>Generally the switch mode power supply input voltage source is constant or shows insignificant little varieties.in any case, when fuel call used input source the last assumption is not valid. A fuel cell stack is give a details of low and not controlled DC output voltage, moreover, when the demanded current increases the output voltage becomes low in a nonlinear form; from now on, suitable controller is required to taken the previously mentioned issues. In this article, a normal current-mode controller is planned to using a joined model for an energy unit stack and a boost converter; besides, the resolving control method increasing the system stability and output voltage regulation.. The proposed energy system utilizes an energy component power (polymer electrolyte film fuel cell) and a boost converter passing on power of 900 W. the proposed controller execution for output voltage regulation by means of closed loop gain estimations and step load changes. What's more, a correlation amongst open-and closed- loop estimations is made, where the controller robustness is tried for vast load varieties and fuel cell stack output voltage changes are shows on simulation results.

scholarly journals Caracterización del método SVPWM con inversor trifásico de dos niveles

2019 ◽  
pp. 22-29
Keyword(s):  
Pulse Width ◽  
Output Voltage ◽  
Pulse Width Modulation ◽  
Harmonic Distortion ◽  
Input Voltage ◽  
Good Choice ◽  
Voltage Source ◽  
Voltage Source Inverter ◽  
Matlab Simulink ◽  
Wide Range

Caracterización del método SVPWM con inversor trifásico de dos niveles Juan Tisza1, 2, Javier Villegas2 1Universidad Nacional de Ingeniería, Av. Túpac Amaru 210, Rímac, Lima Perú 2Universidad Nacional Mayor de San Marcos, Ciudad Universitaria, Lima, Perú Recibido 17 de junio del 2019, Revisado el 17 de julio de 2019 Aceptado el 19 de julio de 2019 DOI: https://doi.org/10.33017/RevECIPeru2019.0005/ Resumen Las cargas en Corriente Alterna (CA) requieren voltaje variable y frecuencia variable. Estos requisitos se cumplen con un inversor de fuente de voltaje (VSI). Se puede lograr un voltaje de salida variable variando la tensión de CC de entrada y manteniendo constante la ganancia del inversor. Por otro lado, si la tensión de entrada CC es fija y no es controlable, se puede lograr una tensión de salida variable variando la ganancia del inversor, lo que normalmente se logra mediante el control de modulación por ancho de pulso dentro del inversor. Hay varias técnicas de modulación de ancho de pulso, pero la técnica de vector espacial es una buena opción entre todas las técnicas para controlar el inversor de fuente de voltaje. La modulación por ancho de pulso de vector espacial (SVPWM) es un método avanzado y muy popular con varias ventajas tales como la utilización efectiva del bus de CC, menos generación de armónicos en voltaje de salida, menos pérdidas de conmutación, amplio rango de modulación lineal, etc. En este documento, se ha tomado un inversor de fuente de voltaje constante CC y se ha implementado la SVPWM para VSI de dos niveles utilizando MATLAB / SIMULINK. Descriptores: Modulación de ancho de pulso (PWM), modulación de ancho de pulso de vector espacial (SVPWM), distorsión armónica total (THD), inversor de fuente de voltaje (VSI). Abstract Alternating Current (AC) loads require variable voltage and variable frequency. These requirements are met by a voltage supply inverter (VSI). A variable output voltage can be achieved by varying the input DC voltage and keeping the inverter gain constant. On the other hand, if the DC input voltage is fixed and not controllable, a variable output voltage can be achieved by varying the gain of the inverter, which is normally achieved by controlling the pulse width modulation within the inverter. There are several pulse width modulation techniques, but the spatial vector technique is a good choice among all the techniques for controlling the voltage source inverter. Spatial vector pulse width modulation (SVPWM) is an advanced and very popular method with several advantages such as effective utilization of CC bus, less harmonic generation in output voltage, less switching losses, wide range of linear modulation, etc. In this document, a CC constant voltage source inverter has been taken and SVPWM has been implemented for two-level VSI using MATLAB / SIMULINK. Keywords: Pulse Width Modulation (PWM), Space Vector Pulse Width Modulation (SVPWM), Total Harmonic Distortion (THD), Voltage Source Inverter (VSI).

scholarly journals Efficient Performance Technical Selection of Positive Buck-Boost Converter

2018 ◽  
Vol 2 (2) ◽  
pp. 20-38
Author(s):  
Ahmed Abbas ◽  
Abadal-Salam Hussain
Keyword(s):  
Pulse Width ◽  
Output Voltage ◽  
Pulse Width Modulation ◽  
Input Voltage ◽  
Boost Converter ◽  
Dc Voltage ◽  
Voltage Polarity ◽  
Efficient Performance ◽  
Efficient Power ◽  
Selection Of

The necessity for stable DC voltage in both removable and non-removable systems has been considerably desired recently. These systems have to be implemented efficiently in order to be responding rapidly based voltage variations. Under this act, the efficient power can extend the lifetime of the employed batteries in such systems. The presented efficiency can be realized with respect to buck and boost components that were implemented to generate what is called positive Buck-Boost converter circuits. The main functions of the positive Buck-Boost converter are identified by announcing the unchanged situation of output voltage polarity and indicating the level of the voltage rationally between the input and the output. It is worth mention, the positive Buck-Boost converter circuit was simulated based Proteus software, and the hardware components were connected in reality. Finally, the microcontroller type that employed in the proposed system is PIC_16F877A, which realizes the input voltage sensitively to generate Pulse Width Modulation (PWM) signals in order to feed the employed MOSFET element.

Sign in / Sign up

Export Citation Format

Share Document