scholarly journals Wind Energy Potential on A Highrise Building: A Preliminary Study

2021 ◽  
Vol 88 (3) ◽  
pp. 20-30
Author(s):  
Nofirman Firdaus ◽  
Bambang Teguh Prasetyo ◽  
Hasnida Ab-Samat ◽  
Prayudi ◽  
Hendri ◽  
...  
Keyword(s):  
Wind Energy ◽  
Weibull Distribution ◽  
Wind Turbine ◽  
Energy Production ◽  
Energy Resource ◽  
Limited Area ◽  
Wake Effect ◽  
Horizontal Axis Wind Turbine ◽  
High Rise ◽  
Power Curves

Indonesia has an abundant renewable energy source. One of them is wind energy resources. Unfortunately, Indonesia's wind energy resource is not fully utilized, especially for application in high-rise buildings. The paper investigates the potential of energy production from the horizontal-axis wind turbine (HAWT) and the vertical-axis wind turbine (VAWT) on the rooftop of a university building in Indonesia. The wind speed data were measured on the rooftop of the building for seven months. The data was analyzed using Weibull distribution. Based on the probability density function of the Weibull distribution, the potential energy production was calculated using the power curves from the manufacturer. Comparing energy production between HAWTs and VAWTs has shown that VAWTs can produce more energy than HAWTs. Using six turbines, VAWTs can produce 48,476 kWh. On the other hand, with four turbines, HAWTs can produce 41,729 kWh. The reason is that VAWT requires shorter distance requirements for inter-turbine and between rows. Therefore, VAWT can use more turbines than HAWT in the limited area. In conclusion, VAWT for high-rise buildings is more preferred because VAWT can generate more energy. Further study should investigate the optimal configuration with varying the wind direction and quantifying the wake effect on power output.

scholarly journals Aerodynamic Performances of Small Scale Horizontal Axis Wind Turbine Blades for Applications in Malaysia

2019 ◽  
Vol 8 (4) ◽  
pp. 9557-9562
Keyword(s):  
Wind Energy ◽  
Wind Turbine ◽  
Turbine Blade ◽  
Power Efficiency ◽  
Energy Production ◽  
Turbine Blades ◽  
Maximum Power ◽  
Small Scale ◽  
Wind Condition ◽  
Horizontal Axis Wind Turbine

Wind energy is one of the most viable options for clean and sustainable energy production. In Malaysia where wind source has been considered scarce, the capacity of installed wind energy production is very low. However, studies have shown that it is worthwhile to produce wind energy at several potential sites in this country. For this purpose, it is crucial that the designed turbine blade gives the highest possible blade power efficiency while structure wise, the turbine blade need to be effective in terms of avoiding possible failures. The maximum power efficiency means the blade does not only provide profile that gives maximum sliding ratio but also it must operate at the corresponding angle of attack, 𝜶𝒎𝒂𝒙 that gives this ratio. At the same time, the blade must be small enough to have low weight to allow it to self-start in the low wind region. In this paper, the study is focused on the aerodynamic aspect of the design of wind turbine blade that will give the maximum power efficiency. Four factors that determine aerodynamic performance of the turbine blades are discussed: the wind condition, the airfoil profile, the blade geometry and the losses. In most of the factor, adjustments are made such that the blade operates at around the 𝜶𝒎𝒂𝒙 so that the sliding ratio and thus power coefficient are maximum.

Design and Test Campaign of a Ducted Horizontal Axis Wind Turbine

2018 ◽  
Author(s):  
Massimo Rivarolo ◽  
Alessandro Spoladore ◽  
Carlo Cravero ◽  
Alberto Traverso ◽  
Andrea Freda ◽  
...  
Keyword(s):  
Energy Harvesting ◽  
Wind Energy ◽  
Wind Turbine ◽  
Energy Production ◽  
Numerical Models ◽  
Electrical Power ◽  
Electrical Energy ◽  
Horizontal Axis ◽  
Horizontal Axis Wind Turbine ◽  
Electrical Energy Production

Electrical energy production by wind energy has assumed more and more relevance in the last years. This paper presents the design of a ducted horizontal axis wind turbine, in order to enhance the performance. The study compares the energy production of a ducted turbine to a traditional free turbine, highlighting the different features. In the first part of the work, different possible geometries have been investigated through a quasi-1D model, using correlations from literature to evaluate pressure, velocity and producible electrical power by the wind turbine. A 3D CFD model, in a set of configurations, has confirmed the preliminary results. The most promising geometries have been selected by combining the outputs of the two models. In order to confirm the results obtained by the numerical models, a test rig has been assembled at the wind tunnel of the Polytechnic School of the University of Genoa. Different possible configurations of the wind energy harvesting system have been tested: free turbine, horizontal duct, convergent duct and convergent-divergent ducts (with the turbine installed in the throat section). In particular, the convergent-divergent duct has shown the best results, with an increase factor close to 2.5 in terms of produced power, compared to the reference free turbine. Finally, the results obtained in the experimental campaign have been used to validate the two models (1D and 3D CFD). Considering the advantages in terms of energy production, this kind of configuration can be considered an interesting solution for many different situations, including energy harvesting.

scholarly journals Air Density Induced Error on Wind Energy Estimation

2019 ◽  
Author(s):  
Aurore Dupré ◽  
Philippe Drobinski ◽  
Jordi Badosa ◽  
Christian Briard ◽  
Riwal Plougonven
Keyword(s):  
Wind Energy ◽  
Wind Power ◽  
Energy Production ◽  
Energy Resource ◽  
Added Value ◽  
Local Analysis ◽  
Mountainous Area ◽  
Air Density ◽  
Temperature And Pressure ◽  
Power Curves

Abstract. In recent years, environmental concerns have encouraged the use of wind power as a renewable energy resource. However, high penetration of the wind power in the electricity system is a challenge due to the uncertainty of wind energy forecast. Estimation of the wind energy production requires a forecast for the wind (the main source of uncertainty) but also of density, often overlooked. Measure of air density is a key for more accurate wind energy prediction. Wind farms often lack instrumentations of temperature and pressure, needed for accurate air density estimation at hub height to be used for locally debiasing air density forecast. In this study, the error budget of air density estimate is computed distinguishing temperature and pressure contributions. The analysis uses measurements for in-depth local analysis as well as meteorological reanalysis to investigate the added-value of a model-based value when measurement is missing. Meteorological reanalysis is also used to study spatial pattern of error budgets (mountainous area, coastal regions, plains, ...). The effect of altitude is carefully accounted for. Temperature is by far the variable inducing the largest errors when it is missing in the air density correction, and replaced by the standard atmosphere value (i.e. 15 °C, used as reference in power curves). It is particularly true for very cold or warm conditions (i.e. far from the standard value), for which the error on wind energy production is nearly halved when an accurate correction of temperature is performed.

Power Optimization of NACA 0018 Airfoil Blade of Horizontal Axis Wind Turbine by CFD Analysis

2020 ◽  
Vol 9 (1) ◽  
pp. 122-139
Author(s):  
Abhishek Choubey ◽  
Prashant Baredar ◽  
Neha Choubey
Keyword(s):  
Wind Energy ◽  
Wind Turbine ◽  
Energy Production ◽  
Mechanical Energy ◽  
Electrical Energy ◽  
Energy Resources ◽  
Cfd Analysis ◽  
Blade Angle ◽  
Horizontal Axis Wind Turbine ◽  
Computational Fluid Dynamics Cfd

The country or region where energy production is based on imported coal or oil will become more self-sufficient by using alternatives such as wind power. Electricity produced by the wind produces no CO2 emissions and therefore does not contribute to the greenhouse effect. Wind energy is relatively labour intensive and thus creates many jobs. Wind energy is the major alternative of conventional energy resources. A wind turbine transforms the kinetic energy in the wind to mechanical energy in a shaft and finally into electrical energy in a generator. The turbine blade is the most important component of any wind turbine. In this article is considered the single airfoil National Advisory Committee for Aeronautics (NACA) 0018 and a computational fluid dynamics (CFD) analysis is done at different blade angles 0º, 10º, 15º, and 30º with a wind velocity of 4 m/s. The analysis results show that a blade angle of 10º gives the best possible power and pressure and velocity distributions are plotted for every case.

scholarly journals Offshore Wind Energy Resource Assessment from Satellite Data Observations and WRF in Porto Santo Island

2020 ◽  
Author(s):  
Fabiola S. Pereira ◽  
Carlos S. Silva
Keyword(s):  
Wind Energy ◽  
Weibull Distribution ◽  
Energy Production ◽  
Energy Resource ◽  
Resource Assessment ◽  
Offshore Wind ◽  
Electricity Production ◽  
Offshore Wind Energy ◽  
Wind Resource Assessment ◽  
Wind Resource

Abstract. The vast majority of isolated electricity production systems such as Islands depends on fossil fuels. Porto Santo Island, a Portuguese UNESCO Biosphere Reserve candidate from Madeira Archipelago situated in the Atlantic Ocean, aims to become a sustainable territory in order to reduce its carbon footprint. A sustainable pathway goes through the integration of renewable energy in the electricity production system, in particular, the potential of offshore wind energy. The scope of this work has three main purposes: (1) the offshore wind resource assessment in Porto Santo Island, (2) the determination of a zone of interest regarding the combination of different parameters such us the bathymetry, distance to the coastline and integrated in the national situation plan of maritime space (3) the estimation of the annual energy production from the best-fitted Weibull Distribution. In the first place, a methodology for data analysis was defined processing netcdf data regarding a ten year wind hindcast from WRF (Weather Research and Forecasting) atmospheric model at 100 m above mean sea level from Ocean Observatory, annual and monthly mean offshore wind energy resource maps were created and a comparison with about 20 year times series of surface winds derived from remotely satellite scatterometer observations at different locations was made. Results show that the average annual mean wind speeds reach the range of 6.6–7.6 m/s in specific areas, situated in the northern part of Porto Santo Island with a Weibull distribution shape parameter (k) of 2.4–2.9. Based on the results, the wind resource assessment, the estimation of the annual wind energy production and capacity factors were calculated from the best-fitted Weibull distribution for each of the geographical coordinates selected. Comparisons with observational data show that WRF model is a proficient wind generating tool. The technical energy production potential and a priority zoning for offshore wind power development is performed using wind turbine generators of 3.3 MW–8.0 MW capacity, that could generate between 12 and 26 GWh of energy per year, while avoiding CO2 emissions. The results show that an offshore wind farm plan is an eligible choice, with an average annual wind power density reaching about 300  W/m2 at 100 m height in the north region.

scholarly journals Potential of wind energy in Medina, Saudi Arabia based on Weibull distribution parameters

2021 ◽  
pp. 0309524X2110273
Author(s):  
Khaled S AlQdah ◽  
Raed Alahmdi ◽  
Abdulrahman Alansari ◽  
Abdulrahman Almoghamisi ◽  
Mohanad Abualkhair ◽  
...  
Keyword(s):  
Power Generation ◽  
Wind Speed ◽  
Wind Energy ◽  
Weibull Distribution ◽  
Wind Turbine ◽  
Energy Production ◽  
Power Production ◽  
Wind Speeds ◽  
Scale Factors ◽  
Distribution Parameters

This study aims to assess the potential of wind energy in Medina by using Weibull probability distribution to provide an insight concerning the energy production from the selected wind turbine Aventa AV-7. Scale factors c and shape k of Weibull distribution, were determined for wind speed frequency. Significant findings included a wind speed recurrence of 2.9 m/s with a probability of 30% approximately. The average c and k were found to be 3.467 and 2.923 m/s, respectively. The estimated average k is relatively high, which indicates that the spread in wind speeds is small. Aventa AV-7 turbine was chosen to test the power generation of wind in Medina. It was found that this wind turbine can generate 8648 kWh/year in the Medina region, which is only 15.2% of the maximum power production. This turbine is expected to generate the maximum possible power output at a wind speed of 7 m/s.

Development and Field Testing of an Inclined Flanged Compact Diffuser for a Micro Wind Turbine

2014 ◽  
Author(s):  
Sandip Kale ◽  
S. N. Sapali
Keyword(s):  
Wind Turbine ◽  
Wind Velocity ◽  
Wind Turbines ◽  
Energy Production ◽  
Cost Effective ◽  
Field Testing ◽  
International Electrotechnical Commission ◽  
Average Wind Speed ◽  
Average Wind ◽  
Power Curves

Micro wind turbines installed in various applications, experience average wind speed for most of the time during operations. Power produced by the wind turbine is proportional to the cubic power of the wind velocity and a small increase in wind velocity results increases power output significantly. The approach wind velocity can be increased by covering traditional wind turbine with a diffuser. Researchers are continuously working to develop a compact, lightweight, cost effective and feasible diffuser for wind turbines. The present work carried out to develop a diffuser with these stated objectives. A compact, lightweight inclined flanged diffuser developed for a micro wind turbine. Bare micro wind turbine and wind turbine covered with developed efficient inclined flanged diffuser tested in the field as per International Electrotechnical Commission (IEC) standards and results presented in the form of power curves. The prediction of annual energy production for both wind turbines determined as per IEC standards.

scholarly journals Tourist Viewshed Externalities and Wind Energy Production

2017 ◽  
Vol 46 (2) ◽  
pp. 224-241 ◽  
Author(s):  
Jacob R. Fooks ◽  
Kent D. Messer ◽  
Joshua M. Duke ◽  
Janet B. Johnson ◽  
Tongzhe Li ◽  
...  
Keyword(s):  
Wind Energy ◽  
Wind Turbine ◽  
Wind Turbines ◽  
Energy Production ◽  
Hotel Room ◽  
Negative Effect ◽  
The Impact ◽  
Large Wind

This study uses an experiment where ferry passengers are sold hotel room “views” to evaluate the impact of wind turbines views on tourists’ vacation experience. Participants purchase a chance for a weekend hotel stay. Information about the hotel rooms was limited to the quality of the hotel and its distance from a large wind turbine, as well as whether or not a particular room would have a view of the turbine. While there was generally a negative effect of turbine views, this did not hold across all participants, and did not seem to be effected by distance or hotel quality.

scholarly journals Inter-annual variability of wind climates and wind turbine annual energy production

2018 ◽  
Author(s):  
Sara C. Pryor ◽  
Tristan J. Shepherd ◽  
Rebecca J. Barthelmie
Keyword(s):  
Standard Deviation ◽  
Wind Energy ◽  
Wind Turbine ◽  
Energy Production ◽  
Wind Farm ◽  
Wind Farms ◽  
Wind Speeds ◽  
Annual Variability ◽  
Eastern Usa

Abstract. Inter-annual variability (IAV) of expected annual energy production (AEP) from proposed wind farms plays a key role in dictating project financing. IAV in pre-construction projected AEP and the difference in 50th and 90th percentile (P50 and P90) AEP derives in part from variability in wind climates. However, the magnitude of IAV in wind speeds at/close to wind turbine hub-heights is poorly constrained and maybe overestimated by the 6 % standard deviation of annual mean wind speeds that is widely applied within the wind energy industry. Thus there is a need for improved understanding of the long-term wind resource and the inter-annual variability therein in order to generate more robust predictions of the financial value of a wind energy project. Long-term simulations of wind speeds near typical wind turbine hub-heights over the eastern USA indicate median gross capacity factors (computed using 10-minute wind speeds close to wind turbine hub-heights and the power curve of the most common wind turbine deployed in the region) that are in good agreement with values derived from operational wind farms. The IAV of annual mean wind speeds at/near to typical wind turbine hub-heights in these simulations is lower than is implied by assuming a standard deviation of 6 %. Indeed, rather than in 9 in 10 years exhibiting AEP within 0.9 and 1.1 times the long-term mean AEP, results presented herein indicate that over 90 % of the area in the eastern USA that currently has operating wind turbines simulated AEP lies within 0.94 and 1.06 of the long-term average. Further, IAV of estimated AEP is not substantially larger than IAV in mean wind speeds. These results indicate it may be appropriate to reduce the IAV applied to pre-construction AEP estimates to account for variability in wind climates, which would decrease the cost of capital for wind farm developments.

scholarly journals Study and Design of a Horizontal Axis Wind Turbine (0.5 kW) Using Software Solid Works

2021 ◽  
pp. 1-17
Author(s):  
Hagninou E. V. Donnou ◽  
Drissa Boro ◽  
Jean Noé Fabiyi ◽  
Marius Tovoeho ◽  
Aristide B. Akpo
Keyword(s):  
Wind Energy ◽  
Wind Turbine ◽  
Wedge Angle ◽  
Three Dimensional ◽  
Synchronous Generator ◽  
Horizontal Axis ◽  
Geometrical Shape ◽  
Horizontal Axis Wind Turbine ◽  
Horizontal Axis Wind Turbines ◽  
Lift And Drag

In the present work, the study and design of a horizontal axis wind turbine suitable for the Cotonou site were investigated on the coast of Benin. A statistical study using the Weibull distribution was carried out on the hourly wind data measured at 10 m from the ground by the Agency for Air Navigation Safety in Africa and Madagascar (ASECNA) over the period from January 1981 to December 2014. Then, the models, techniques, tools and approaches used to design horizontal axis wind turbines were presented and the wind turbine components characteristics were determined. The numerical design and assembly of these components were carried out using SolidWorks software. The results revealed that the designed wind turbine has a power of 571W. It is equipped with a permanent magnet synchronous generator and has three aluminum blades with NACA 4412 biconvex asymmetrical profile. The values obtained for the optimum coefficient of lift and drag are estimated at 1.196 and 0.0189 respectively. The blades are characterised by an attack optimum angle estimated at 6° and the wedge angle at 5°. Their length is 2.50 m and the maximum thickness is estimated at 0.032 m for a rope length of 0.27 m. The wind turbine efficiency is 44%. The computer program designed on SolidWorks gives three-dimensional views of the geometrical shape of the wind turbine components and their assembly has allowed to visualize the compact shape of the wind turbine after export via its graphical interface. The energy quantity that can be obtained from the wind turbine was estimated at 2712,718 kWh/year. This wind turbine design study is the first of its kind for the study area. In order to reduce the technological dependence and the import of wind energy systems, the results of this study could be used to produce lower cost wind energy available on our study site.

Sign in / Sign up

Export Citation Format

Share Document