Flow and Heat Transfer Within a Rectangular Film Cooling Hole of Normal Injection Angle

2004 ◽  
Vol 28 (4) ◽  
pp. 456-466
Keyword(s):  
Heat Transfer ◽  
Film Cooling ◽  
Injection Angle ◽  
Flow And Heat Transfer ◽  
Cooling Hole

Combined Experimental and CFD Study of a HP Blade Multi-Pass Cooling System

2009 ◽  
Author(s):  
D. Jackson ◽  
P. Ireland ◽  
B. Cheong
Keyword(s):  
Heat Transfer ◽  
Film Cooling ◽  
Cooling System ◽  
Detailed Comparison ◽  
Bulk Temperature ◽  
Internal Cooling ◽  
3 Dimensional ◽  
Turbine Cooling ◽  
Cooling Hole ◽  
The Difference

Progress in the computing power available for CFD predictions now means that full geometry, 3 dimensional predictions are now routinely used in internal cooling system design. This paper reports recent work at Rolls-Royce which has compared the flow and htc predictions in a modern HP turbine cooling system to experiments. The triple pass cooling system includes film cooling vents and inclined ribs. The high resolution heat transfer experiments show that different cooling performance features are predicted with different levels of fidelity by the CFD. The research also revealed the sensitivity of the prediction to accurate modelling of the film cooling hole discharge coefficients and a detailed comparison of the authors’ computer predictions to data available in the literature is reported. Mixed bulk temperature is frequently used in the determination of heat transfer coefficient from experimental data. The current CFD data is used to compare the mixed bulk temperature to the duct centreline temperature. The latter is measured experimentally and the effect of the difference between mixed bulk and centreline temperature is considered in detail.

Effect of a Ceramic Matrix Composite Surface on Film Cooling

2021 ◽  
Author(s):  
Peter H. Wilkins ◽  
Stephen P. Lynch ◽  
Karen A. Thole ◽  
San Quach ◽  
Tyler Vincent ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Matrix Composite ◽  
Film Cooling ◽  
Gas Turbines ◽  
Ceramic Matrix Composite ◽  
Ceramic Matrix ◽  
Composite Surface ◽  
Minimal Impact ◽  
Cooling Hole ◽  
Adiabatic Effectiveness

Abstract Ceramic matrix composite (CMC) parts create the opportunity for increased turbine entry temperatures within gas turbines. To achieve the highest temperatures possible, film cooling will play an important role in allowing turbine entry temperatures to exceed acceptable surface temperatures for CMC components, just as it does for the current generation of gas turbine components. Film cooling over a CMC surface introduces new challenges including roughness features downstream of the cooling holes and changes to the hole exit due to uneven surface topography. To better understand these impacts, this study presents flowfield and adiabatic effectiveness CFD for a 7-7-7 shaped film cooling hole at two CMC weave orientations. The CMC surface selected is a 5 Harness Satin weave pattern that is examined at two different orientations. To understand the ability of steady RANS to predict flow and convective heat transfer over a CMC surface, the weave surface is initially simulated without film and compared to previous experimental results. The simulation of the weave orientation of 0°, with fewer features projecting into the flow, matches fairly well to the experiment, and demonstrates a minimal impact on film cooling leading to only slightly lower adiabatic effectiveness compared to a smooth surface. However, the simulation of the 90° orientation with a large number of protruding features does not match the experimentally observed surface heat transfer. The additional protruding surface produces degraded film cooling performance at low blowing ratios but is less sensitive to blowing ratio, leading to improved relative performance at higher blowing ratios, particularly in regions far downstream of the hole.

Numerical Study on Flow and Heat Transfer of a Cooled First Stage Vane of a Gas Turbine

2016 ◽  
Author(s):  
Lv Ye ◽  
Zhao Liu ◽  
Xiangyu Wang ◽  
Zhenping Feng
Keyword(s):  
Heat Transfer ◽  
Gas Turbine ◽  
Film Cooling ◽  
Numerical Study ◽  
Coolant Flow ◽  
The Other ◽  
Edge Region ◽  
Flow Rates ◽  
Flow And Heat Transfer ◽  
Film Cooling Holes

This paper presents a numerical simulation of composite cooling on a first stage vane of a gas turbine, in which gas by fixed composition mixture is adopted. To investigate the flow and heat transfer characteristics, two internal chambers which contain multiple arrays of impingement holes are arranged in the vane, several arrays of pin-fins are arranged in the trailing edge region, and a few arrays of film cooling holes are arranged on the vane surfaces to form the cooling film. The coolant enters through the shroud inlet, and then divided into two parts. One part is transferred into the chamber in the leading edge region, and then after impinging on the target surfaces, it proceeds further to go through the film cooling holes distributed on the vane surface, while the other part enters into the second chamber immediately and then exits to the mainstream in two ways to effectively cool the other sections of the vane. In this study, five different coolant flow rates and six different inlet pressure ratios were investigated. All the cases were performed with the same domain grids and same boundary conditions. It can be concluded that for the internal surfaces, the heat transfer coefficient changes gradually with the coolant flow rate and the inlet total pressure ratio, while for the external surfaces, the average cooling effectiveness increases with the increase of coolant mass flow rates while decreases with the increase of the inlet stagnation pressure ratios within the study range.

Computational Analysis of Conjugate Heat Transfer and Particulate Deposition on a High Pressure Turbine Vane

2009 ◽  
Author(s):  
Weiguo Ai ◽  
Thomas H. Fletcher
Keyword(s):  
Heat Transfer ◽  
Film Cooling ◽  
Conjugate Heat Transfer ◽  
Particle Method ◽  
Experimental Results ◽  
Turbine Vane ◽  
Particulate Deposition ◽  
Cooling Hole ◽  
Lagrangian Particle Method ◽  
Film Cooling Holes

Numerical computations were conducted to simulate flyash deposition experiments on gas turbine disk samples with internal impingement and film cooling using a CFD code (FLUENT). The standard k-ω turbulence model and RANS were employed to compute the flow field and heat transfer. The boundary conditions were specified to be in agreement with the conditions measured in experiments performed in the BYU Turbine Accelerated Deposition Facility (TADF). A Lagrangian particle method was utilized to predict the ash particulate deposition. User-defined subroutines were linked with FLUENT to build the deposition model. The model includes particle sticking/rebounding and particle detachment, which are applied to the interaction of particles with the impinged wall surface to describe the particle behavior. Conjugate heat transfer calculations were performed to determine the temperature distribution and heat transfer coefficient in the region close to the film-cooling hole and in the regions further downstream of a row of film-cooling holes. Computational and experimental results were compared to understand the effect of film hole spacing, hole size and TBC on surface heat transfer. Calculated capture efficiencies compare well with experimental results.

scholarly journals Experimental Investigation of Heat Transfer in Two-Pass Coolant Passages With Ribs and Film Cooling Hole Ejection

2002 ◽  
Author(s):  
D. Chanteloup ◽  
A. Bo¨lcs
Keyword(s):  
Heat Transfer ◽  
Film Cooling ◽  
Outer Wall ◽  
Reynolds Numbers ◽  
Thermochromic Liquid Crystal ◽  
Heat Transfer Characteristics ◽  
Surface Heat Transfer Coefficient ◽  
Staggered Arrangement ◽  
Cooling Hole ◽  
Surface Measurements

A study of flow in two stationary models of two-pass internal coolant passages is presented, which focuses on the heat transfer characteristics in the two-pass coolant channel. Heat transfer measurements were made with a transient technique using thermochromic liquid crystal technique to measure a surface temperature. The technique allows full surface heat transfer coefficient measurements on all the walls. The coolant passage model consisted of two square passages, each having a 20 hydraulic diameter length, separated by a rounded-tip web of 0.2 passage widths, and connected by a sharp 180 deg bend with a rectangular outer wall. Ribs were mounted on the bottom and top walls of both legs, with a staggered arrangement, and at 45 deg to the flow. The rib height and spacing were 0.1 and 1.0 passage heights, respectively. The measurements were obtained for Reynolds numbers of 25000, 50000 and 70000. One geometry is equipped with extraction holes to simulate holes for film cooling. Two series of holes are placed solely in the bottom wall, 4 holes are located in the bend, and 12 in the downstream leg. The global extraction through the holes was set to 30%, 40% and 50% of the inlet massflow. This paper presents new measurements of the heat transfer in the straight legs, and in the bend of the passage. It shows the influence of Reynolds number and extraction on full surface measurements and area averaged results.

Numerical Study of Heat Transfer and Cooling Effectiveness on a Flat-Tip Turbine Blade

2013 ◽  
Author(s):  
Qihe Huang ◽  
Jiao Wang ◽  
Lei He ◽  
Qiang Xu
Keyword(s):  
Heat Transfer ◽  
Turbine Blade ◽  
Film Cooling ◽  
Numerical Study ◽  
Leakage Flow ◽  
Tip Leakage Flow ◽  
Cooling Effectiveness ◽  
Blowing Ratio ◽  
Flow And Heat Transfer ◽  
Blade Tip

A numerical study is performed to simulate the tip leakage flow and heat transfer on the first stage rotor blade tip of GE-E3 turbine, which represents a modern gas turbine blade geometry. Calculations consist of the flat blade tip without and with film cooling. For the flat tip without film cooling case, in order to investigate the effect of tip gap clearance on the leakage flow and heat transfer on the blade tip, three different tip gap clearances of 1.0%, 1.5% and 2.5% of the blade span are considered. And to assess the performance of the turbulence models in correctly predicting the blade tip heat transfer, the simulations have been performed by using four different models (the standard k-ε, the RNG k-ε, the standard k-ω and the SST models), and the comparison shows that the standard k-ω model provides the best results. All the calculations of the flat tip without film cooling have been compared and validated with the experimental data of Azad[1] and the predictions of Yang[2]. For the flat tip with film cooling case, three different blowing ratio (M = 0.5, 1.0, and 1.5) have been studied to the influence on the leakage flow in tip gap and the cooling effectiveness on the blade tip. Tip film cooling can largely reduce the overall heat transfer on the tip. And the blowing ratio M = 1.0, the cooling effect for the blade tip is the best.

Sign in / Sign up

Export Citation Format

Share Document