scholarly journals RME CO-COMBUSTION WITH HYDROGEN IN COMPRESSION IGNITION ENGINE: PERFORMANCE, EFFICIENCY AND EMISSIONS / SLĖGINIO UŽDEGIMO VARIKLIO ENERGINIŲ, EFEKTYVUMO IR DEGINIŲ EMISIJOS RODIKLIŲ TYRIMAS NAUDOJANT RAPSŲ METILESTERĮ IR VANDENILĮ

2018 ◽  
Vol 10 (0) ◽  
pp. 1-9
Author(s):  
Romualdas Juknelevičius
Keyword(s):  
Combustion Process ◽  
Engine Performance ◽  
Fuel Mixture ◽  
Common Rail ◽  
Injection System ◽  
Intake Manifold ◽  
Compression Ignition Engine ◽  
Common Rail Injection System ◽  
Wide Range ◽  
The Rich

The article presents the test results of the single cylinder CI engine with common rail injection system operating on biofuel – Rapeseed Methyl Ester with addition supply of hydrogen. The purpose of this investigation was to examine the influence of the hydrogen addition to the biofuel on combustion phases, engine performance, efficiency, and exhaust emissions. HES was changed within the range from 0 to 44%. Hydrogen was injected into the intake manifold, where it created homogeneous mixture with air. Tests were performed at both fixed and optimal injection timings at low, medium and nominal engine load. After analysis of the engine bench tests and simulation with AVL BOOST software, it was observed that lean hydrogen – RME mixture does not support the flame propagation and efficient combustion. While at the rich fuel mixture and with increasing hydrogen fraction, the combustion intensity concentrate at the beginning of the combustion process and shortened the ignition delay phase. AVL BOOST simulation performed within the wide range of HES (16–80%) revealed that combustion intensity moves to the beginning of combustion with increase of HES. Decrease of CO, CO2 and smoke opacity was observed with increase of hydrogen amounts to the engine. However, increase of the NO concentration in the engine exhaust gases was observed. Santrauka Straipsnyje pateikti tyrimo rezultatai, gauti atlikus bandymą vieno cilindro slėginio uždegimo variklyje su biodegalais – rapsų metilesterį (RME) ir vandenilį. Biodegalai įpurškiami akumuliatorine įpurškimo sistema „Common rail“. Šio tyrimo tikslas – ištirti, kaip vandenilis veikia biodegalų degimą, variklio veikimą, jo efektyvumą ir deginių susidarymą. Vandenilio energinė dalis degimo mišinyje buvo keičiama nuo 0 iki 44 %. Vandenilis buvo tiekiamas įsiurbimo fazės metu įsiurbimo kanalu į degimo kamerą, kurioje jis, susimaišęs su oru, sudaro homogeninį mišinį. Bandymai buvo atliekami nekeičiant įpurškimo kampo, nustačius optimalų įpurškimo kampą esant žemai, vidutinei ir nominaliai variklio apkrovai. Išnagrinėjus variklio bandymų rezultatus ir sumodeliavu AVL BOOST programa, buvo pastebėta, kad, esant liesam vandenilio ir RME mišiniui, liepsnos plitimas yra lėtas, mišinys dega neveiksmingai. Tačiau riebus degalų mišinys ir padidinta vandenilio energijos dalis užtikrina degimo intensyvumą degimo proceso pradžioje ir sutrumpina uždegimo gaišties trukmę. AVL BOOST modeliavimas, atliktas plačiu vandenilio energijos dalies diapazonu (16–80 %), patvirtino teiginį, kad degimas tampa intensyvesnis degimo pradžioje dėl padidinto vandenilio kiekio. Didinant vandenilio kiekį, buvo pastebėta, kad išmetamosiose dujose sumažėjo CO, CO2 ir kietųjų dalelių, tačiau padidėjo NO koncentracija.

scholarly journals EXPERIMENTAL INVESTIGATIONS OF HYDROGEN EFFECTS ON PERFORMANCE AND EMISSIONS OF RENEWABLE DIESEL FUELED RCCI / VANDENILIO ĮTAKA ENERGINIAMS IR EMISIJOS RODIKLIAMS ALTERNATYVIU DYZELINU VEIKIANČIAME RCCI VARIKLYJE – EKSPERIMENTINIS TYRIMAS

2018 ◽  
Vol 10 (0) ◽  
pp. 1-10
Author(s):  
Romualdas Juknelevičius
Keyword(s):  
Combustion Chamber ◽  
Combustion Process ◽  
Engine Performance ◽  
Fuel Mixture ◽  
Injection System ◽  
Experimental Investigations ◽  
Renewable Diesel ◽  
Common Rail Injection System ◽  
Performance And Emissions ◽  
The Rich

The article presents the study of hydrogen effects on performance, combustion and emissions characteristics of renewable diesel fueled single cylinder CI engine with common rail injection system in RCCI mode. The renewable diesel fuels as the HRF are the HVO and it blend with petrol diesel further named PRO Diesel, investigated in this study. The purpose of this investigation was to examine the influence of the LRF – hydrogen addition to the HRF on combustion phases, engine performance, efficiency, and exhaust emissions. HES was changed within the range from 0 to 35%. Hydrogen injected through PFI during intake stroke to the combustion chamber, where it created homogeneous mixture with air. The HRF was directly injected into combustion chamber using electronic controlled unit. Tests were performed at both fixed and optimal injection timings at low, medium and nominal engine load. After analysis of the engine bench results, it was observed that lean hydrogen – HRF mixture does not support the flame propagation and efficient combustion. While at the rich fuel mixture and with increasing hydrogen fraction, the combustion intensity concentrate at the beginning of the combustion process and shortened the ignition delay phase. Decrease of CO, CO2 and smoke opacity was observed with increase of hydrogen amounts to the engine. However, increase of the NO concentration in the engine exhaust gases was observed.

scholarly journals Research on combustion process of gasoline homogenous charge compression ignition engine

2018 ◽  
Vol 184 ◽  
pp. 01013
Author(s):  
Corneliu Cofaru ◽  
Mihaela Virginia Popescu
Keyword(s):  
Experimental Research ◽  
Fuel Injection ◽  
Combustion Process ◽  
Fuel Mixture ◽  
Spark Ignition Engine ◽  
Injection System ◽  
Compression Ignition ◽  
Compression Ignition Engine ◽  
Engine Operation ◽  
Homogenous Charge Compression Ignition

The paper presents the research designed to develop a HCCI (Homogenous Charge Compression Ignition) engine starting from a spark ignition engine platform. The chosen test engine was a single cylinder, four strokes provided with a carburettor. The results of experimental research data obtained on this version were used as a baseline for the next phase of the research. In order to obtain the HCCI configuration, the engine was modified, as follows: the compression ratio was increased from 9.7 to 11.5 to ensure that the air – fuel mixture auto-ignite and to improve the engine efficiency; the carburettor was replaced by a direct fuel injection system in order to control precisely the fuel mass per cycle taking into account the measured intake air-mass; the valves shape were modified to provide a safety engine operation by ensuring the provision of sufficient clearance beetween the valve and the piston; the exchange gas system was changed from fixed timing to variable valve timing to have the possibilities of modification of quantities of trapped burnt gases. The cylinder processes were simulated on virtual model. The experimental research works were focused on determining the parameters which control the combustion timing of HCCI engine to obtain the best energetic and ecologic parameters.

scholarly journals Theoretical study to determine the proper injection system for upgrading fuel system of diesel engine om357 to common rail system

2018 ◽  
Vol 7 (4) ◽  
pp. 2594
Author(s):  
Razieh Pourdarbani ◽  
Ramin Aminfar
Keyword(s):  
Diesel Engine ◽  
Fuel Injection ◽  
Engine Performance ◽  
Injection Pressure ◽  
Common Rail ◽  
Injection System ◽  
Injection Timing ◽  
Common Rail System ◽  
Common Rail Injection System ◽  
Multi Stage

In this research, we tried to investigate all the fuel injection systems of diesel engines in order to select the most suitable fuel injection system for the OM357 diesel engine to achieve the highest efficiency, maximize output torque and reduce emissions and even reduce fuel consumption. The prevailing strategy for this study was to investigate the effect of injection pressure changes, injection timing and multi-stage injection. By comparing the engines equipped with common rail injection system, the proposed injector for engine OM357 is solenoid, due to the cost of this type of injector, MAP and controller (ECU). It is clear that this will not be possible only with the optimization of the injection system, and so other systems that influence engine performance such as the engine's respiratory system and combustion chamber shape, etc. should also be optimized. 

UV-Visible Emission Spectroscopy of the Combustion Process in a Common Rail Cl Engine Fulled with N-Butanol - Diesel Blends

2013 ◽  
Vol 390 ◽  
pp. 286-290 ◽  
Author(s):  
Cinzia Tornatore ◽  
Luca Marchitto ◽  
Simona Silvia Merola ◽  
Gerardo Valentino
Keyword(s):  
Emission Spectroscopy ◽  
Soot Formation ◽  
Combustion Process ◽  
Common Rail ◽  
Injection System ◽  
Optical Data ◽  
Spray Combustion ◽  
Compression Ignition ◽  
Compression Ignition Engine ◽  
Uv Visible

This paper is focused on the study of the effects of the injection strategy and fuel blends on spray combustion and soot formation in compression ignition engines. UV-visible natural emission spectroscopy was applied in the combustion chamber of a single cylinder high swirl compression ignition engine equipped with a common rail multi-jet injection system. The engine was fuelled with low-sulphur neat diesel and blended with 20 and 40% by volume of n-butanol. For all the fuels, the evolution of radical species, such like OH and soot was followed during the spray combustion processes examining different pilot-main dwell timings. Optical data were correlated to engine parameters and exhaust emissions.

scholarly journals An experimental analysis of performance and exhaust emissions of a CRDI diesel engine operating on mixtures containing mineral and renewable components

2019 ◽  
Vol 179 (4) ◽  
pp. 27-31
Author(s):  
Kamil DUDA ◽  
Sławomir WIERZBICKI ◽  
Maciej MIKULSKI
Keyword(s):  
Diesel Engine ◽  
Raw Materials ◽  
Methyl Esters ◽  
Direct Injection ◽  
Fuel Mixture ◽  
Common Rail ◽  
Injection System ◽  
Compression Ignition Engine ◽  
Load Range ◽  
Performance And Emission

The manuscript presents a comparative analysis of the performance and emission characteristics of a compression ignition engine equipped with a Common Rail injection system. The engine is fueled with diesel-biodiesel mixtures containing 25% and 50% share (by volume) of renewable components. Conventional diesel is used as a reference. Turkey lard and rapeseed oil are used as raw materials and subjected to the single-stage transesterification process to obtain methyl esters. The experiments are performed on a medium-duty, turbocharged, inter-cooled, Common Rail Direct Injection (CRDI) diesel engine. This study concentrates on one engine speed of 1500 rpm, typical for gen-set applications, and mid-load range from 100 Nm to 200 Nm. The scope of measurements covers the analysis of exhaust gasses concentration and engine efficiency parameters. In addition, the in-cylinder pressure measurements are performed in order to provide insight into the differences in combustion characteristics between examined fuel mixtures. The study reveals that the addition of the renewable component to fuel mixture positively affects a number of examined performance parameters as well as decreases the concentration of the examined toxic exhaust components, in the majority of cases.

Optimal Design of a Two-Stroke Diesel Engine for Aeronautical Applications Concerning Both Thermofluidynamic and Acoustic Issues

2008 ◽  
Author(s):  
Daniela Siano ◽  
Michela Costa ◽  
Fabio Bozza
Keyword(s):  
Diesel Engine ◽  
Acoustic Analysis ◽  
Fluid Dynamic ◽  
Combustion Process ◽  
Engine Performance ◽  
Combustion Noise ◽  
Process Efficiency ◽  
Injection System ◽  
Common Rail Injection System ◽  
First Choice

Some aspects concerning the development of a prototype of a diesel engine suitable for aeronautical applications are discussed. The engine aimed at achieving a weight to power ratio equal to one kg/kW (220 kg for 220 kW) is conceived in a two stroke Uniflow configuration and constituted by six cylinders distributed on two parallel banks. Basing on a first choice of some geometrical and operational data, a preliminary fluid-dynamic and acoustic analysis is carried out at the sea level. This includes the engine-turbocharger matching, the estimation of the scavenging process efficiency, and the simulation of the spray and combustion process, arising from a Common Rail injection system. Both 1D and 3D CFD models are employed. In-cylinder pressure cycles are utilized to numerically predict the combustion noise. The acoustic study is based on the integration of FEM/BEM codes. In order to improve the engine performance and vibro-acoustic behaviour, the 1D model, tuned with information derived from the 3D code, is linked to an external optimiziation code (ModeFRONTIER™). A constrained multi-objective optimization is performed to contemporary minimize the fuel consumption and the maximum in-cylinder temperature and pressure gradient. In this way a better selection of a number of engine parameters is carried out (exhaust valve opening, closing and lift, intake ports heights, start of injection, etc). The best found solution is finally compared to the initial one and some substantial design improvements are discussed.

scholarly journals Pyrolysis oil combustion in the CI engine

2019 ◽  
Vol 179 (4) ◽  
pp. 126-131
Author(s):  
Mariusz CHWIST ◽  
Karol GRAB-ROGALIŃSKI ◽  
Stanisław SZWAJA
Keyword(s):  
Diesel Fuel ◽  
Combustion Process ◽  
Calorific Value ◽  
Injection System ◽  
Pyrolysis Oil ◽  
Compression Ignition Engine ◽  
Common Rail Injection System ◽  
Biomass Processing ◽  
Common Rail Injection ◽  
Ci Engine

Pyrolysis oil obtained from thermal biomass processing (torrefaction and pyrolysis) was used as an additional fuel for the compression-ignition engine equipped with a classic (non-common rail) injection system. The basic fuel used to the engine was regular diesel fuel. The tests were carried out with two content of pyrolysis oil in diesel fuel as follows: 10 and 20% by volume. In addition, the combustion process was investigated in the engine operating only on pyrolysis oil. The test results were based on a comparative analysis, where the diesel fuel was used as the reference fuel. The obtained results indicate that is a real possibility of co-combustion of pyrolysis oil with diesel fuel in the CI engine. On the other hand, a decrease in engine power resulting from the lower calorific value of pyrolysis oil and a greater unrepeatability of engine consecutive work cycles were observed.

Sign in / Sign up

Export Citation Format

Share Document