scholarly journals Influence of bagasse ash with different fineness on alkali-silica reactivity of mortar

2018 ◽  
Vol 68 (332) ◽  
pp. 169 ◽  
Author(s):  
S. Ramjan ◽  
W. Tangchirapat ◽  
C. Jaturapitakkul
Keyword(s):  
Particle Size ◽  
Compressive Strength ◽  
Portland Cement ◽  
Large Particle ◽  
Ordinary Portland Cement ◽  
Alkali Silica Reaction ◽  
Large Particle Size ◽  
High Compressive Strength ◽  
Alkali Silica Reactivity

This research aimed to study the effect of finenesses of bagasse ash (BGA) on the alkali-silica reaction of mortar. The BGA sample was ground to have particles retained on a sieve No. 325 of 33±1% and 5±1% by weight. Ground BGA samples were used separately to replace ordinary Portland cement (OPC) at rates of 10, 20, 30 and 40% by weight of binder to cast mortars. The compressive strengths and the alkali-silica reaction (ASR) of mortars were investigated. The results showed that a large particle size of BGA is not suitable for use in lowering ASR because it results in a low compressive strength and high expansion due to ASR. The mortars containing BGA with higher fineness exhibited higher compressive strength and lower expansion due to ASR than the mortars containing BGA with lower fineness. The results also suggested that the ground BGA retained on a sieve No. 325 of less than 5% by weight is suitable to be used as a good pozzolan which provides high compressive strength and reduces the expansion of mortar due to ASR even though it contains high LOI. The obtained results also encourage the utilization of ground BGA effectively which leads to reduce the disposal of bagasse ash.

Study on Waterproof and Water-Resistant Properties of Gypsum

2012 ◽  
Vol 476-478 ◽  
pp. 1585-1588
Author(s):  
Hong Pan ◽  
Guo Zhong Li
Keyword(s):  
Compressive Strength ◽  
Flexural Strength ◽  
Portland Cement ◽  
Water Absorption ◽  
Ordinary Portland Cement ◽  
Experimental Results ◽  
Softening Coefficient

The comprehensively modified effect of cement, VAE emulsion and self-made acrylic varnish on mechanical and water-resistant properties of gypsum sample was investigated and microstructure of gypsum sample was analyzed. Experimental results exhibit that absolutely dry flexural strength, absolutely dry compressive strength, water absorption and softening coefficient of gypsum specimen with admixture of 10% ordinary Portland cement and 6% VAE emulsion and acrylic varnish coated on its surface can respectively reach to 5.11MPa , 10.49 MPa, 8.32% and 0.63, respectively.

Hevea Latex of Large Particle Size

1939 ◽  
Vol 31 (12) ◽  
pp. 1509-1512 ◽  
Author(s):  
J. McGavack
Keyword(s):  
Particle Size ◽  
Large Particle ◽  
Large Particle Size

scholarly journals The Effect of Nano Metakaolin Material on Some Properties of Concrete

2013 ◽  
Vol 6 (1) ◽  
pp. 50-61
Author(s):  
Amer M. Ibrahem ◽  
Shakir A. Al-Mishhadani ◽  
Zeinab H.Naji
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Portland Cement ◽  
Water Absorption ◽  
Thermal Activation ◽  
Ordinary Portland Cement ◽  
Splitting Tensile Strength ◽  
Kaolin Clay ◽  
Cement Ratio ◽  
Water Cement Ratio

This investigation aimed to study the effect of nano metakaolin ( NMK ) on some properties (compressive strength ,splitting tensile strength & water absorption ) of concrete. The nano metakaolin (NMK) was prepared by thermal activation of kaolin clay for 2 hours at 750 Ċ. The cement used in this investigation consists of ordinary Portland cement (OPC). The OPC was partially substituted by NMK of ( 3, 5 & 10%) by weight of cement. The C45 concrete was prepared , using water/cement ratio ( W/c) of (0.53) .The Water absorption was tested at 28 days while the tests (compressive strength ,splitting tensile strength) were tested at ages of (7, 28, 60,& 90) days . The compressive strength and splitting tensile strength of concrete with NMK were higher than that of reference concrete with the same W/c ratio.The improvement in the compressive strength when using NMK was (42.2, 55.8 , 63.1% ) at age 28 days for ( 3%, 5%, &10% ) replacement of NMK respectively whereas the improvement in the splitting tensile strength was (0% , 36% & 46.8 %) at age of 28 days when using (3%, 5%, &10% ) NMK respectively. The improvement in the water absorption was (16.6%, 21.79%, &25.6 ) when using (3, 5, &10% )NMK.

scholarly journals Utilization of Sugarcane Bagasse Ash from Power Co-generation Boilers as a Supplementary Cementitious Material

2021 ◽  
Vol 2 (2) ◽  
Author(s):  
Safiki Ainomugisha ◽  
Bisaso Edwin ◽  
Bazairwe Annet
Keyword(s):  
Compressive Strength ◽  
Portland Cement ◽  
Sugarcane Bagasse ◽  
Low Income ◽  
Ordinary Portland Cement ◽  
Construction Material ◽  
Sustainable Construction ◽  
Partial Replacement ◽  
Hardened Concrete ◽  
Sugarcane Bagasse Ash

Concrete has been the world’s most consumed construction material, with over 10 billion tons of concrete annually. This is mainly due to its excellent mechanical and durability properties plus high mouldability. However, one of its major constituents; Ordinary Portland Cement is reported to be expensive and unaffordable by most low-income earners. Its production contributes about 5%–8% of global CO2 greenhouse emissions. This is most likely to increase exponentially with the demand of Ordinary Portland Cement estimated to rise by 200%, reaching 6000 million tons/year by 2050.  Therefore, different countries are aiming at finding alternative sustainable construction materials that are more affordable and offer greener options reducing reliance on non-renewable sources. Therefore, this study aimed at assessing the possibility of utilizing sugarcane bagasse ash from co-generation in sugar factories as supplementary material in concrete. Physical and chemical properties of this sugarcane bagasse ash were obtained plus physical and mechanical properties of fresh and hardened concrete made with partial replacement of Ordinary Portland Cement. Cost-benefit analysis of concrete was also assessed. The study was carried using 63 concrete cubes of size 150cm3 with water absorption studied as per BS 1881-122; slump test to BS 1881-102; and compressive strength and density of concrete according to BS 1881-116. The cement binder was replaced with sugarcane bagasse ash 0%, 5%, 10%, 15%, 20%, 25% and 30% by proportion of weight. Results showed the bulk density of sugarcane bagasse ash at 474.33kg/m3, the specific gravity of 1.81, and 65% of bagasse ash has a particle size of less than 0.28mm. Chemically, sugarcane bagasse ash contained SiO2, Fe2O3, and Al2O3 at 63.59%, 3.39%, and 5.66% respectively. A 10% replacement of cement gave optimum compressive strength of 26.17MPa. This 10% replacement demonstrated a cost saving of 5.65% compared with conventional concrete. 

scholarly journals Chloride Ingress in Chemically Activated Calcined Clay-Based Cement

2018 ◽  
Vol 2018 ◽  
pp. 1-8 ◽  
Author(s):  
Joseph Mwiti Marangu ◽  
Joseph Karanja Thiong’o ◽  
Jackson Muthengia Wachira
Keyword(s):  
Compressive Strength ◽  
Portland Cement ◽  
Ordinary Portland Cement ◽  
Strength Development ◽  
Chloride Ingress ◽  
Calcined Clay ◽  
Apparent Diffusion Coefficients ◽  
Apparent Diffusion ◽  
Lower Porosity ◽  
Lower Chloride

Chloride-laden environments pose serious durability concerns in cement based materials. This paper presents the findings of chloride ingress in chemically activated calcined Clay-Ordinary Portland Cement blended mortars. Results are also presented for compressive strength development and porosity tests. Sampled clays were incinerated at a temperature of 800°C for 4 hours. The resultant calcined clay was blended with Ordinary Portland Cement (OPC) at replacement level of 35% by mass of OPC to make test cement labeled PCC35. Mortar prisms measuring 40 mm × 40 mm × 160 mm were cast using PCC35 with 0.5 M Na2SO4 solution as a chemical activator instead of water. Compressive strength was determined at 28th day of curing. As a control, OPC, Portland Pozzolana Cement (PPC), and PCC35 were similarly investigated without use of activator. After the 28th day of curing, mortar specimens were subjected to accelerated chloride ingress, porosity, compressive strength tests, and chloride profiling. Subsequently, apparent diffusion coefficients (Dapp) were estimated from solutions to Fick’s second law of diffusion. Compressive strength increased after exposure to the chloride rich media in all cement categories. Chemically activated PCC35 exhibited higher compressive strength compared to nonactivated PCC35. However, chemically activated PCC35 had the least gain in compressive strength, lower porosity, and lower chloride ingress in terms of Dapp, compared to OPC, PPC, and nonactivated PCC35.

Quaternary blended cement mortars containing wood ash, glass and slag powders

2021 ◽  
Author(s):  
Eethar Thanon Dawood ◽  
Marwa Saadi Mhmood
Keyword(s):  
Compressive Strength ◽  
Portland Cement ◽  
Ordinary Portland Cement ◽  
Glass Powder ◽  
Steel Slag ◽  
Wood Ash ◽  
Supplementary Cementitious Materials ◽  
Partial Replacement ◽  
Slag Powder ◽  
Steel Slag Powder

AbstractA quaternary supplementary cementitious materials as partial replacement of ordinary Portland cement decreases CO2 emission. This paper has investigated the properties of mortars made from different quaternary blends of wood ash, steel slag powder and glass powder with ordinary Portland cement at different replacement levels of 0, 24, 25, and 30% by weight of the binder. The blended mortar mixtures tested for flow, compressive strength and density. The results showed that the flow of mortars is decreased with the combined use of steel slag powder, glass powder, and wood ash compared with control mix. Compressive strength reduced with the combination of steel slag powder, glass powder and wood ash but this reduction effects is acceptable especially at 24% replacement contain super-plasticizer compared with the ecological benefit.

scholarly journals Physical Properties of Concrete Containing Graphene Oxide Nanosheets

Materials ◽  
2019 ◽  
Vol 12 (10) ◽  
pp. 1707 ◽  
Author(s):  
Yu-You Wu ◽  
Longxin Que ◽  
Zhaoyang Cui ◽  
Paul Lambert
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Graphene Oxide ◽  
Flexural Strength ◽  
Portland Cement ◽  
Physical Properties ◽  
Ordinary Portland Cement ◽  
Construction Materials ◽  
Split Tensile Strength ◽  
Cement Pastes

Concrete made from ordinary Portland cement is one of the most widely used construction materials due to its excellent compressive strength. However, concrete lacks ductility resulting in low tensile strength and flexural strength, and poor resistance to crack formation. Studies have demonstrated that the addition of graphene oxide (GO) nanosheet can effectively enhance the compressive and flexural properties of ordinary Portland cement paste, confirming GO nanosheet as an excellent candidate for using as nano-reinforcement in cement-based composites. To date, the majority of studies have focused on cement pastes and mortars. Only limited investigations into concretes incorporating GO nanosheets have been reported. This paper presents an experimental investigation on the slump and physical properties of concrete reinforced with GO nanosheets at additions from 0.00% to 0.08% by weight of cement and a water–cement ratio of 0.5. The study demonstrates that the addition of GO nanosheets improves the compressive strength, flexural strength, and split tensile strength of concrete, whereas the slump of concrete decreases with increasing GO nanosheet content. The results also demonstrate that 0.03% by weight of cement is the optimum value of GO nanosheet dosage for improving the split tensile strength of concrete.

Microwave-assisted removal of sulfur in large particle size coal by bromine water

Fuel ◽  
2021 ◽  
Vol 289 ◽  
pp. 119838
Author(s):  
Xiaogang Mu ◽  
Jinfang Liu ◽  
Fei Gao ◽  
Cunbao Deng ◽  
Zhixin Jin ◽  
...  
Keyword(s):  
Particle Size ◽  
Large Particle ◽  
Large Particle Size ◽  
Bromine Water ◽  
Microwave Assisted
Sign in / Sign up

Export Citation Format

Share Document