Comparative Study of Two Different Converters with its Controller for Grid Connected WECS with PMSG

2019 ◽  
Vol 8 (2) ◽  
pp. 1-24
Author(s):  
Sasmita Behera ◽  
Matruprasad Jyotiranjan
Keyword(s):  
Power Quality ◽  
Pulse Width Modulation ◽  
Harmonic Distortion ◽  
Synchronous Generator ◽  
Electrical Energy ◽  
Maximum Power ◽  
Multilevel Inverter ◽  
Resistive Load ◽  
Power Extraction ◽  
Point Tracking

Wind is a source for generating clean and economical electrical energy with a proper harnessing mechanism. For a wind energy conversion system (WECS), maximum power extraction with optimum power quality is required. In this article, the grid power quality is enhanced, using a multilevel inverter which provides smoother and pure sinusoidal waves as compared to two-level inverter by decreasing total harmonic distortion (THD) in WECS with a permanent magnet synchronous generator (PMSG). Also, a maximum power point tracking (MPPT) algorithm is based on an optimal torque controller, employed to extract more power. In this study, a WECS with a PMSG connected to the local linear resistive load and grid is considered for simulation. A multilevel inverter grid interface is controlled by in phase disposition pulse width modulation (IPD – PWM). The multilevel inverter with MPPT has been acknowledged as superior to a normal two-level inverter without MPPT Controller. Simulation results as observed for fixed and variable wind speed including MPPT demonstrate benefits of the proposed method.

scholarly journals Practical Maximum-Power Extraction in Single Microbial Fuel Cell by Effective Delivery through Power Management System

Energies ◽  
2018 ◽  
Vol 11 (9) ◽  
pp. 2312
Author(s):  
Jeongjin Yeo ◽  
Taeyoung Kim ◽  
Jae Jang ◽  
Yoonseok Yang
Keyword(s):  
Fuel Cell ◽  
Microbial Fuel Cell ◽  
Power Management ◽  
Operation Time ◽  
Electrical Energy ◽  
Maximum Power ◽  
Extraction Technology ◽  
Power Extraction ◽  
Point Tracking ◽  
Power Point

Power management systems (PMSs) are essential for the practical use of microbial fuel cell (MFC) technology, as they replace the unstable stacking of MFCs with step-up voltage conversion. Maximum-power extraction technology could improve the power output of MFCs; however, owing to the power consumption of the PMS operation, the maximum-power extraction point cannot deliver maximum power to the application load. This study proposes a practical power extraction for single MFCs, which reserves more electrical energy for an application load than conventional maximum power-point tracking (MPPT). When experimentally validated on a real MFC, the proposed method delivered higher output power during a longer PMS operation time than MPPT. The maximum power delivery enables more effective power conditioning of various micro-energy harvesting systems.

scholarly journals Maximum Power Extraction from Active Pitch Controlled Standalone Variable Speed Wind Turbine

2019 ◽  
Vol 9 (2) ◽  
pp. 3226-3229
Keyword(s):  
Wind Turbine ◽  
Wind Velocity ◽  
Synchronous Generator ◽  
Maximum Energy ◽  
Maximum Power ◽  
Resistive Load ◽  
Variable Speed ◽  
Permanent Magnet Synchronous Generator ◽  
Power Extraction ◽  
Variable Speed Wind Turbine

This paper focuses on modelling of a standalone variable speed wind turbine using MATLAB and increasing its performance by extracting the maximum power below rated wind velocity using MPPT algorithm and maintaining constant power using active pitch angle control for above rated wind velocity. The wind turbine is coupled to a Permanent Magnet Synchronous Generator (PMSG) which can operate on variable speed. A variable resistive load will extract the maximum energy possible and utilise it for heating applications.

scholarly journals Modelling of a PMSG Wind Turbine with Autonomous Control

2014 ◽  
Vol 2014 ◽  
pp. 1-9 ◽  
Author(s):  
Chia-Nan Wang ◽  
Wen-Chang Lin ◽  
Xuan-Khoa Le
Keyword(s):  
Wind Turbine ◽  
Power Flow ◽  
Pulse Width Modulation ◽  
High Efficiency ◽  
Synchronous Generator ◽  
Maximum Power ◽  
Autonomous Control ◽  
Voltage Source ◽  
Point Tracking ◽  
Grid Side

The aim of this research is to model an autonomous control wind turbine driven permanent magnetic synchronous generator (PMSG) which feeds alternating current (AC) power to the utility grid. Furthermore, this research also demonstrates the effects and the efficiency of PMSG wind turbine which is integrated by autonomous controllers. In order for well autonomous control, two voltage source inverters are used to control wind turbine connecting with the grid. The generator-side inverter is used to adjust the synchronous generator as well as separating the generator from the grid when necessary. The grid-side inverter controls the power flow between the direct current (DC) bus and the AC side. Both of them are oriented control by space vector pulse width modulation (PWM) with back-to-back frequency inverter. Moreover, the proportional-integral (PI) controller is enhanced to control both of the inverters and the pitch angle of the wind turbine. Maximum power point tracking (MPPT) is integrated in generator-side inverter to track the maximum power, when wind speed changes. The simulation results in Matlab Simulink 2012b showing the model have good dynamic and static performance. The maximum power can be tracked and the generator wind turbine can be operated with high efficiency.

scholarly journals Energy transformation without using filter on high resistive load

2020 ◽  
Vol 40 (1) ◽  
pp. 39-42 ◽  
Author(s):  
Erol Can
Keyword(s):  
Pulse Width Modulation ◽  
Harmonic Distortion ◽  
Multilevel Inverter ◽  
Switching Function ◽  
Resistive Load ◽  
Energy Transformation ◽  
Operation Characteristic ◽  
Mathematical Equations ◽  
Ieee Standard ◽  
Multi Level

In this paper, 9-level, 17-level, 19-level, 21-level, 27-level, and 39- level inverters with SPWM are presented. According to a switching function, the high-multilevel inverter design has been described since a new multi-level inverter structure is considered. The multilevel inverter structure is designed with placing switches and sources on levels. Pulse width modulation, controlling switches in the inverter structure, is also produced by comparison between triangles and sinus signals. Operating sequences of the switches are given in the table in order to demonstrate the inverter operation characteristic with the produced signals. Then, mathematical equations are formed by considering an operation of switches on the load. In simulations and experiments, the 9-level, 17- level, 19-level, 21-level, 27-level, and 39-level inverters are performed on the resistance (R) and inductance (L) loads with different resistance, because it is difficult to generate current and voltage with an acceptable harmonic distortion on the impedances which have high ohmic values. After applications of experimentation and simulation, the obtained results are compared with other published papers of results and the international IEEE standard, which is 5% for harmonic distortions of creating currents and voltages.

scholarly journals MPPT of Magnus Wind System with DC Servo Drive for the Cylinders and Boost Converter

2015 ◽  
Vol 2015 ◽  
pp. 1-10
Author(s):  
Maro Jinbo ◽  
Felix Alberto Farret ◽  
Ghendy Cardoso Junior ◽  
Daniel Senter ◽  
Marcelo Franklin Lorensetti
Keyword(s):  
Synchronous Generator ◽  
Boost Converter ◽  
Maximum Power ◽  
Hill Climbing ◽  
Resistive Load ◽  
Wind System ◽  
Servo Drive ◽  
Point Tracking ◽  
Power Point ◽  
The One

This paper presents an algorithm MPPT (Maximum Power Point Tracking) for a Magnus wind system with a DC servo drive system (DC drive and BLDC motor) to rotate the turbine cylinders. The optimal cylinders rotation is the one to deliver the maximum power extracted from the wind tracked by fixed and adaptive step HCC (Hill Climbing Control) acting on the servo drive. The proposed wind system consists of a PMSG (Permanent Magnet Synchronous Generator), a three-phase diode rectifier, a DC/DC (boost) converter, and a resistive load. Furthermore, the boost converter acts with the fixed step HCC algorithm to track the maximum power operating point. Therefore, the MPPT for a Magnus wind system requires both tracking for the optimal cylinder speed and the optimal generator speed.

scholarly journals Expert Control Systems for Maximum Power Point Tracking in a Wind Turbine with PMSG: State of the Art

2019 ◽  
Vol 9 (12) ◽  
pp. 2469 ◽  
Author(s):  
Ernesto Chavero-Navarrete ◽  
Mario Trejo-Perea ◽  
Juan Carlos Jáuregui-Correa ◽  
Roberto Valentín Carrillo-Serrano ◽  
José Gabriel Ríos-Moreno
Keyword(s):  
Wind Turbine ◽  
Control Systems ◽  
Fundamental Problem ◽  
Electrical Power ◽  
Synchronous Generator ◽  
Electrical Energy ◽  
Maximum Power ◽  
Expert Control ◽  
Point Tracking ◽  
Wide Range

Wind power is a renewable energy source that has been developed in recent years. Large turbines are increasingly seen. The advantage of generating electrical power in this way is that it can be connected to the grid, making it an economical and easily available source of energy. The fundamental problem of a wind turbine is the randomness in a wide range of wind speeds that determine the electrical energy generated, as well as abrupt changes in wind speed that make the system unstable and unsafe. A conventional control system based on a mathematical model is effective with moderate disturbances, but slow with very large oscillations such as those produced by turbulence. To solve this problem, expert control systems (ECS) are proposed, which are based on human experience and an adequate management of stored information of each of its variables, providing a way to determine solutions. This revision of recent years, mentions the expert systems developed to obtain the point of maximum power generation in a wind turbine with permanent magnet synchronous generator (PMSG) and, therefore, offers a control solution that adapts to the specifications of any wind turbine.

scholarly journals Design and Validation of BAT Algorithm-Based Photovoltaic System Using Simplified High Gain Quasi Boost Inverter

Energies ◽  
2021 ◽  
Vol 14 (4) ◽  
pp. 1086
Author(s):  
Mani Rajalakshmi ◽  
Sankaralingam Chandramohan ◽  
Raju Kannadasan ◽  
Mohammed H. Alsharif ◽  
Mun-Kyeom Kim ◽  
...  
Keyword(s):  
Power Quality ◽  
Harmonic Distortion ◽  
Bat Algorithm ◽  
High Gain ◽  
Maximum Power ◽  
Photovoltaic System ◽  
Prototype Model ◽  
Conventional System ◽  
Pv System ◽  
Power Extraction

Owing to the intermittent nature of renewable energy systems, an improved power extraction technique and modernized power modulators are to be designed to overcome power quality challenges. Attesting to this fact, this work aims to enhance the efficiency of the photovoltaic (PV) system using the BAT algorithm (BA) and enhances the overall performance of the system using modified inverter topology. Specifically, a new power electronic modulator, i.e., a simplified high gain quasi-boost inverter (SHGqBI), is implemented to eliminate the downsides of the conventional system. The proposed inverter reduces the additional components that can condense the volume of the design with reduced conduction and switching losses. The combination of BA-based PV rated 250 W and novel inverter configuration pick the global peak power with enhanced power quality. Notably, BA extracts the maximum power from the panel meritoriously with about 98.8% efficiency. This is because BA uses the global input parameters to track the maximum power of the PV panel, whereas other conventional maximum power point tracking (MPPT) techniques used limited parameters. Further, the current and voltage total harmonic distortion (THD) of the proposed inverter are recorded, which show a commendable range of 2.7% and 10.2%, respectively. In addition, the efficiency of the inverter is found to be 97%. Consequently, the overall system efficiency is calculated and found to be 97.9%, providing greater advantages over a conventional system. The system is mathematically modelled using MATLAB/Simulink and validated through an experimental setup with the laboratory prototype model.

Design & Real-time Implementation of MIDO Converter Based PV Water Pumping System with BES

2020 ◽  
Vol 14 (2) ◽  
pp. 194-204
Author(s):  
Anuradha Tomar
Keyword(s):  
Real Time ◽  
Rural Areas ◽  
Maximum Power ◽  
Pump System ◽  
Partial Shading ◽  
Power Extraction ◽  
Pumping System ◽  
Point Tracking ◽  
Water Pumping ◽  
Battery Energy

Background: Despite so many developments, most of the farmers in the rural areas are still dependent on rainwater, rivers or water wells, for irrigation, drinking water etc. The main reason behind such dependency is non-connectivity with the National grid and thus unavailability of electricity. To extract the maximum power from solar photovoltaic (SPV) based system, implementation of Maximum Power Point Tracking (MPPT) is mandatory. PV power is intermittent in nature. Variation in the irradiation level due to partial shading or mismatching phenomena leads to the development of modular DC-DC converters. Methods: A stand-alone Multi-Input Dual-Output (MIDO) DC-DC converter based SPV system, is installed at a farm; surrounded with plants for water pumping with stable flow (not pulsating) along with battery energy storage (BES) for lighting. The proposed work has two main objectives; first to maximize the available PV power under shadowing and mismatching condition in case of series/ parallel connected PV modules and second is to improve the utilization of available PV energy with dual loads connected to it. Implementation of proposed MIDO converter along with BES addresses these objectives. First, MIDO controller ensures the MPPT operation of the SPV system to extract maximum power even under partial shading condition and second, controls the power supplied to the motor-pump system and BES. The proposed system is simulated in MATLAB/ SIMULINK environment. Real-time experimental readings under natural sun irradiance through hardware set-up are also taken under dynamic field conditions to validate the performance. Results and Conclusion: The inherent advantage of individual MPPT of each PV source in MIDO configuration, under varying shadow patterns due to surrounding plants and trees is added to common DC bus and therefore provides a better impact on PV power extraction as compared to conventional PV based water pumping system. Multi-outputs at different supply voltages is another flag of MIDO system. Both these aspects are implemented and working successfully at 92.75% efficiency.

scholarly journals An Advanced Control Technique for Power Quality Improvement of Grid-Tied Multilevel Inverter

2021 ◽  
Vol 13 (2) ◽  
pp. 505
Author(s):  
Sumaya Jahan ◽  
Shuvra Prokash Biswas ◽  
Md. Kamal Hosain ◽  
Md. Rabiul Islam ◽  
Safa Haq ◽  
...  
Keyword(s):  
Power Quality ◽  
Harmonic Distortion ◽  
Multilevel Inverter ◽  
Control Technique ◽  
Solar Pv ◽  
Pv System ◽  
Reference Tracking ◽  
Proportional Integral ◽  
Lead Compensator ◽  
Power Quality Improvement

The use of different control techniques has become very popular for controlling the performance of grid-connected photovoltaic (PV) systems. Although the proportional-integral (PI) control technique is very popular, there are some difficulties such as less stability, slow dynamic response, low reference tracking capability, and lower output power quality in solar PV applications. In this paper, a robust, fast, and dynamic proportional-integral resonance controller with a harmonic and lead compensator (PIR + HC + LC) is proposed to control the current of a 15-level neutral-point-clamped (NPC) multilevel inverter. The proposed controlled is basically a proportional-integral resonance (PIR) controller with the feedback of a harmonic compensator and a lead compensator. The performance of the proposed controller is analyzed in a MATLAB/Simulink environment. The simulation result represents admirable performance in terms of stability, sudden load change response, fault handling capability, reference tracking capability, and total harmonic distortion (THD) than those of the existing controllers. The responses of the inverter and grid outlets under different conditions are also analyzed. The harmonic compensator decreases the lower order harmonics of grid voltage and current, and the lead compensator provides the phase lead. It is expected that the proposed controller is a dynamic aspirant in the grid-connected PV system.

scholarly journals Hybrid Fuzzy Based MPPT Techniques for Maximum Power Extraction

2019 ◽  
Vol 8 (2S8) ◽  
pp. 1140-1148
Keyword(s):  
Maximum Power ◽  
Photovoltaic System ◽  
Voltage Source ◽  
Voltage Source Converter ◽  
Pv System ◽  
Power Extraction ◽  
Point Tracking ◽  
Power Point Tracking ◽  
Incremental Conductance ◽  
Power Point

The extensive usage of solar has extended the opportunity of research to increase the efficiency of PV module. Maximum Power Point Tracking technique plays an important role. In P & O and Incremental conductance the power produced is less. In this paper a Fuzzy based P & O and Fuzzy based Incremental Conductance MPPT techniques are presented to extract the maximum power from the photovoltaic system by considering the dynamic variation in irradiations and temperature also. Here the 100 kW PV array is considered and it is connected to the utility grid via a DC-DC boost converter of 500volts with a 3 phase three level voltage source converter. The result is obtained by the MAT LAB Simulink and the same is appraised with the traditional P & O and Incremental conductance. The PV System produces the maximum power by the application of Fuzzy based incremental Technique compared to conventional methods.

Sign in / Sign up

Export Citation Format

Share Document