Characteristics of Lean and Stoichiometric Combustion of Compressed Natural Gas in a Direct Injection Engine

2011 ◽  
Vol 110-116 ◽  
pp. 357-369 ◽  
Author(s):  
Raja Shahzad ◽  
P. Naveenchandran ◽  
A. Rashid ◽  
Amir Aziz
Keyword(s):  
Fuel Injection ◽  
Direct Injection ◽  
Engine Performance ◽  
Initial Mixture ◽  
Combustion Characteristics ◽  
Injection Timing ◽  
Direct Injection Engine ◽  
Fuel Injection Timing ◽  
Initial Stage ◽  
Air Mixing

This paper discusses the combustion characteristics of CNG under lean and stochiometric conditions in a direct injection engine. The experiments were carried out on a dedicated CNG-Direct Injection engine with 14:1 compression ratio. Combustion characteristics of CNG have been investigated on various injection timings. Injection timing of the fuel injection timing had significant effects on the engine performance, combustion and emissions. The effects became more significant when injection timing was retarded. Injection timing was set after the closing of intake valve and experiments are conducted at 0% and 50% load conditions. Lean stratified operation experiences faster combustion compared to that of stochiometric. In lean stratified operation, there were fast burn rates at the initial stage and slower burning at the later stage. Whereas in stochiometric conditions there is a slightly slower burn at the initial stage and a moderately faster burn at the later stage. The faster initial combustion in lean stratified operation might be due to rapid burn of the initial mixture due to higher turbulence, while a slower burn in the later stage due to diffusion. In contrary to that in stochiometric operations the initial burn is slightly slower, due to moderately strong turbulence and a faster burn due to moderately proceeding mixture. Thus the main effect of fuel injection timing can be explained by the fuel air mixing and the turbulence produced.

Effect of Fuel Injection Timing Relative to Ignition Timing on the Natural-Gas Direct-Injection Combustion

2001 ◽  
Author(s):  
Zuohua Huang ◽  
Seiichi Shiga ◽  
Takamasa Ueda ◽  
Nobuhisa Jingu ◽  
Hisao Nakamura ◽  
...  
Keyword(s):  
Heat Release ◽  
Late Stage ◽  
Equivalence Ratio ◽  
Fuel Injection ◽  
Direct Injection ◽  
Injection Timing ◽  
Ignition Timing ◽  
Fuel Injection Timing ◽  
Initial Stage ◽  
Wide Range

Abstract Effect of fuel injection timing relative to ignition timing on natural gas direct-injection combustion was studied by using a rapid compression machine. The ignition timing was fixed at 80 ms from the compression start. When the injection timing was relatively earlier (injection start at 60 ms), the heat release pattern showed slower burn in the initial stage and faster burn in the late stage, which is similar to that of flame propagation of a premixed gas. In contrast to this, when the injection timing was relatively later (injection start at 75 ms), the heat release rate showed faster burn in the initial stage and slower burn in the late stage, which is similar to that of diesel combustion. The shortest duration was realized at the injection end timing of 80 ms (the same timing as the ignition timing) over the wide range of equivalence ratio. The degree of charge stratification and the intensity of turbulence generated by the fuel jet is considered to cause these behaviors. Earlier injection leads to longer duration of the initial combustion, whereas the later injection does longer duration of the late combustion. Earlier injection showed relatively lower CO emission while later injection produces relatively lower NOx emission. It was suggested that earlier injection leads to lower mixture stratification combustion and later injection leads to higher mixture stratification combustion. Combustion efficiency maintained high value over the wide range of equivalence ratio.

Combustion Characteristics of Methane Direct Injection Engine Under Various Injection Timings and Injection Pressures

2016 ◽  
Author(s):  
Jingeun Song ◽  
Mingi Choi ◽  
Daesik Kim ◽  
Sungwook Park
Keyword(s):  
Fuel Injection ◽  
Direct Injection ◽  
Injection Pressure ◽  
Combustion Characteristics ◽  
Injection Timing ◽  
Direct Injection Engine ◽  
Optical Engine ◽  
Start Of Injection ◽  
Crank Angle ◽  
Injection Pressures

The performance of a methane direct injection engine was investigated under various fuel injection timings and injection pressures. A single-cylinder optical engine was used to acquire in-cylinder pressure data and flame images. An outward-opening injector was installed at the center of the cylinder head. Experimental results showed that the combustion characteristics were strongly influenced by the end of injection timing rather than the start of injection timing. Late injection enhanced the combustion speed because the short duration between the end of injection and the spark induced strong turbulence. The flame propagation speeds under various injection timings were directly compared using crank-angle-resolved sequential flame images. The injection pressure was not an important factor in the combustion; the three injection pressure cases of 0.5, 0.8, and 1.1 MPa yielded similar combustion trends. In the cases of late injection, the injection timings of which were near the Intake Valve Closing (IVC) timing, the volumetric efficiency was higher (by 4%) than in the earlier injection cases. This result implies that the methane direct injection engine can achieve higher torque by means of the late injection strategy.

Effect of Fuel Injection Timing Relative to Ignition Timing on the Natural-Gas Direct-Injection Combustion

2003 ◽  
Vol 125 (3) ◽  
pp. 783-790 ◽  
Author(s):  
Z. Huang ◽  
S. Shiga ◽  
T. Ueda ◽  
H. Nakamura ◽  
T. Ishima ◽  
...  
Keyword(s):  
Late Stage ◽  
Equivalence Ratio ◽  
Fuel Injection ◽  
Direct Injection ◽  
Injection Timing ◽  
Ignition Timing ◽  
Fuel Injection Timing ◽  
Initial Stage ◽  
Wide Range ◽  
Early Injection

The effect of fuel injection timing relative to ignition timing on natural gas direct-injection combustion was studied by using a rapid compression machine (RCM). The ignition timing was fixed at 80 ms after the compression start. When the injection timing was relatively early (injection start at 60 ms), the heat release pattern showed a slower burn in the initial stage and a faster burn in the late stage, which is similar to that of flame propagation of a premixed gas. In contrast to this, when the injection timing was relatively late (injection start at 75 ms), the heat release rate showed a faster burn in the initial stage and a slower burn in the late stage, which is similar to that of diesel combustion. The shortest duration was realized at the injection end timing of 80 ms (the same timing as the ignition timing) over a wide range of equivalence ratio. The degree of charge stratification and the intensity of turbulence generated by the fuel jet are considered to cause this behavior. Early injection leads to longer duration of the initial combustion, whereas late injection leads to a longer duration of the late combustion. Early injection showed relatively lower CO concentration in the combustion products while late injection gave relatively lower NOx. It was suggested that early injection leads to combustion with weaker stratification, and late injection leads to combustion with stronger stratification. Combustion efficiency was kept at a high value over a wide range of equivalence ratio.

Effect of Injection Timing on Combustion Characteristics of a DI Diesel Engine Fuelled with Pistacia chinensis Bunge Seed Biodiesel

2012 ◽  
Vol 614-615 ◽  
pp. 337-342
Author(s):  
Li Luo ◽  
Bin Xu ◽  
Zhi Hao Ma ◽  
Jian Wu ◽  
Ming Li
Keyword(s):  
Combustion Temperature ◽  
Fuel Injection ◽  
Direct Injection ◽  
Combustion Characteristics ◽  
Injection Timing ◽  
Brake Specific Fuel Consumption ◽  
Cylinder Pressure ◽  
Combustion Duration ◽  
Di Diesel Engine ◽  
Maximum Combustion Temperature

In this study, the effect of injection timing on combustion characteristics of a direct injection, electronically controlled, high pressure, common rail, turbocharged and intercooled engine fuelled with different pistacia chinensis bunge seed biodiesel/diesel blends has been experimentally investigated. The results indicated that brake specific fuel consumption reduces with the increasing of fuel injection advance angle and enhances with the increasing of biodiesel content in the blends. The peak of cylinder pressure and maximum combustion temperature increase evidently with the increment of fuel injection advance angle. However, the combustion of biodiesel blends starts earlier than diesel at the same fuel injection advance angle. At both conditions, the combustion duration and the peak of heat release rate are insensitive to the changing of injection timing.

Influence of fuel injection strategies on efficiency and particulate emissions of gasoline and ethanol blends in a turbocharged multi-cylinder direct injection engine

2019 ◽  
Vol 22 (1) ◽  
pp. 152-164 ◽  
Author(s):  
Ripudaman Singh ◽  
Taehoon Han ◽  
Mohammad Fatouraie ◽  
Andrew Mansfield ◽  
Margaret Wooldridge ◽  
...  
Keyword(s):  
Thermal Efficiency ◽  
Fuel Injection ◽  
Direct Injection ◽  
Injection Timing ◽  
Multiple Injection ◽  
Fuel Mass ◽  
Direct Injection Engine ◽  
Fuel Blends ◽  
Ethanol Blends ◽  
Injection Strategies

The effects of a broad range of fuel injection strategies on thermal efficiency and engine-out emissions (CO, total hydrocarbons, NOx and particulate number) were studied for gasoline and ethanol fuel blends. A state-of-the-art production multi-cylinder turbocharged gasoline direct injection engine equipped with piezoelectric injectors was used to study fuels and fueling strategies not previously considered in the literature. A large parametric space was considered including up to four fuel injection events with variable injection timing and variable fuel mass in each injection event. Fuel blends of E30 (30% by volume ethanol) and E85 (85% by volume ethanol) were compared with baseline E0 (reference grade gasoline). The engine was operated over a range of loads with intake manifold absolute pressure from 800 to 1200 mbar. A combined application of ethanol blends with a multiple injection strategy yielded considerable improvement in engine-out particulate and gaseous emissions while maintaining or slightly improving engine brake thermal efficiency. The weighted injection spread parameter defined in this study, combined with the weighted center of injection timing defined in the previous literature, was found well suited to characterize multiple injection strategies, including the effects of the number of injections, fuel mass in each injection and the dwell time between injections.

Effect of Fuel Injection Timing During Negative Valve Overlap Period on a GDI-HCCI Engine

2018 ◽  
Author(s):  
Sok Ratnak ◽  
Jin Kusaka ◽  
Yasuhiro Daisho ◽  
Kei Yoshimura ◽  
Kenjiro Nakama
Keyword(s):  
Fuel Injection ◽  
Direct Injection ◽  
Single Pulse ◽  
Injection Timing ◽  
Pulse Injection ◽  
Hcci Combustion ◽  
Fuel Injection Timing ◽  
Intake Stroke ◽  
Negative Valve Overlap ◽  
Valve Overlap

Gasoline Direct Injection Homogeneous Charge Compression (GDI-HCCI) combustion is achieved by closing early the exhaust valves for trapping hot residual gases combined with direct fuel injection. The combustion is chemically controlled by multi-point auto-ignition which its main combustion phase can be controlled by direct injection timing of fuel. This work investigates the effect of single pulse injection timing on a supercharged GDI-HCCI combustion engine by using a four-stroke single cylinder engine with a side-mounted direct fuel injector. Injection of primary reference fuel PRF90 under the near-stoichiometric-boosted condition is studied. The fuel is injected during negative valve overlap (NVO) or recompression period for fuel reformation under low oxygen concentration and the injection is retarded to intake stroke for the homogeneous mixture. It is found that the early fuel injection in NVO period advances the combustion phasing compared with the retarded injection in the intake stroke. Noticeable slower combustion rate from intake stroke fuel injection is obtained compared with the NVO injection due to charge cooling effect. Zero-dimensional combustion simulations with multiple chemical reaction mechanisms are simulated to provide chemical understanding from the effect of fuel injection timing on intermediate species generations. The species such as C2H4, C3H6, CH4, and H2 are found to be formed during the NVO injection period from the calculations. The effects of single pulse injection timings on combustion characteristics such pressure rise rate, combustion stability, and emissions are also discussed in this study.

Combustion Characteristics of Methane Direct Injection Engine Under Various Injection Timings and Injection Pressures

2017 ◽  
Vol 139 (8) ◽  
Author(s):  
Jingeun Song ◽  
Mingi Choi ◽  
Daesik Kim ◽  
Sungwook Park
Keyword(s):  
Fuel Injection ◽  
Direct Injection ◽  
Injection Pressure ◽  
Combustion Characteristics ◽  
Direct Injection Engine ◽  
Optical Engine ◽  
Start Of Injection ◽  
Crank Angle ◽  
Combustion Speed ◽  
Injection Pressures

The performance of a methane direct injection engine was investigated under various fuel injection timings and injection pressures. A single-cylinder optical engine was used to acquire in-cylinder pressure data and flame images. An outward-opening injector was installed at the center of the cylinder head. Experimental results showed that the combustion characteristics were strongly influenced by the end of injection (EOI) timing rather than the start of injection (SOI) timing. Late injection enhanced the combustion speed because the short duration between the end of injection and the spark-induced strong turbulence. The flame propagation speeds under various injection timings were directly compared using crank-angle-resolved sequential flame images. The injection pressure was not an important factor in the combustion; the three injection pressure cases of 0.5, 0.8, and 1.1 MPa yielded similar combustion trends. In the cases of late injection, the injection timings of which were near the intake valve closing (IVC) timing, the volumetric efficiency was higher (by 4%) than in the earlier injection cases. This result implies that the methane direct injection engine can achieve higher torque by means of the late injection strategy.

Distribution of Two-Stage Direct Injection CNG-Air Mixture near Lean Limit Using CFD

2013 ◽  
Vol 465-466 ◽  
pp. 448-452
Author(s):  
Mas Fawzi ◽  
Bukhari Manshoor ◽  
Yoshiyuki Kidoguchi ◽  
Yuzuru Nada
Keyword(s):  
Fuel Injection ◽  
Direct Injection ◽  
Engine Performance ◽  
Injection Pressure ◽  
Gas Jet ◽  
Exhaust Emission ◽  
Injection Technique ◽  
Injection Timing ◽  
Two Stage ◽  
Lean Burn

Previous work shows that gas-jet ignition with two-stage injection technique is effective to extend lean combustible ranges of CNG engines. In this report, the robustness of the gas-jet ignition with two-stage injection method was investigated purposely to improve the performance of a lean burn direct injection CNG engine. The experiment was conducted using an engine at speed of 900 rpm, fuel-injection-pressure of 3MPa, equivalence ratio at 0.8, and ignition timing at top dead center. The effect of first injection timing on the test engine performance and exhaust emission was analyzed. First injection timings near the gas-jet ignition produced unstable combustion with occurrence of misfires except at a timing which produced distinctively good combustion with low HC and CO emissions. Computational fluid dynamics was used to provide hindsight of the fuel-air mixture distribution that might be the cause of misfires occurrence at certain injection timings.

Sign in / Sign up

Export Citation Format

Share Document