Effect of Nano Silica and Ultrafine Fly Ash on Compressive Strength of High Volume Fly Ash Mortar

2013 ◽  
Vol 368-370 ◽  
pp. 1061-1065 ◽  
Author(s):  
Steve W.M. Supit ◽  
Faiz U.A. Shaikh ◽  
Prabir K. Sarker
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
High Volume ◽  
Partial Replacement ◽  
Strength Development ◽  
Test Results ◽  
X Ray Diffraction ◽  
Nano Silica ◽  
High Volume Fly Ash ◽  
Class F Fly Ash

This paper evaluates the effect of Ultrafine Fly Ash (UFFA) and nanoSilica (NS) on compressive strength of high volume fly ash (HVFA) mortar at 7 days and 28 days. Three series of mortar mixes are considered in the first part of this study. In the first series the effect of high content of class F fly ash as partial replacement of cement at 40, 50 and 60% (by wt.) are considered. While in the second and third series, the UFFA and NS are used as partial replacement of cement at 5%, 8%, 10%, 12% and 15% and 1%, 2%, 4%, 6% and 8% (by wt.) of cement, respectively. The UFFA and the NS content which exhibited highest compressive strength in the above series are used in the second part where their effects on the compressive strength of HVFA mortars are evaluated. Results show that the mortar containing 10% UFFA as partial replacement of cement exhibited the highest compressive strength at both 7 and 28 days among all UFFA contents. Similarly, the mortar containing 2% NS as partial replacement of cement exhibited the best performance. Interestingly, the use of UFFA in HVFA mortars did not improve the compressive strength. However, the use of 2% and 4% NS showed improvement in the compressive strength of HVFA mortar containing 40% and 50% fly ash at both ages. The effects of NS and UFFA on the hydration and strength development of HVFA mortar is also evaluated through X-Ray Diffraction (XRD) test. Results also show that the UFFA and NS can significantly reduce the calcium hydroxide (CH) in HVFA mortars.

High Volume Slag and Slag-Fly Ash Blended Cement Pastes Containing Nano Silica

2019 ◽  
Vol 967 ◽  
pp. 205-213
Author(s):  
Faiz U.A. Shaikh ◽  
Anwar Hosan
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Cement Paste ◽  
Ordinary Portland Cement ◽  
Blended Cement ◽  
High Volume ◽  
Ash Content ◽  
Partial Replacement ◽  
Nano Silica ◽  
Cement Pastes

This paper presents the effect of nanosilica (NS) on compressive strength and microstructure of cement paste containing high volume slag and high volume slag-fly ash blend as partial replacement of ordinary Portland cement (OPC). Results show that high volume slag (HVS) cement paste containing 60% slag exhibited about 4% higher compressive strength than control cement paste, while the HVS cement paste containing 70% slag maintained the similar compressive strength to control cement paste. However, about 9% and 37% reduction in compressive strength in HVS cement pastes is observed due to use of 80% and 90% slag, respectively. The high volume slag-fly ash (HVSFA) cement pastes containing total slag and fly ash content of 60% exhibited about 5%-16% higher compressive strength than control cement paste. However, significant reduction in compressive strength is observed in higher slag-fly ash blends with increasing in fly ash contents. Results also show that the addition of 1-4% NS improves the compressive strength of HVS cement paste containing 70% slag by about 9-24%. However, at higher slag contents of 80% and 90% this improvement is even higher e.g. 11-29% and 17-41%, respectively. The NS addition also improves the compressive strength by about 1-59% and 5-21% in high volume slag-fly ash cement pastes containing 21% fly ash+49%slag and 24% fly ash+56%slag, respectively. The thermogravimetric analysis (TGA) results confirm the reduction of calcium hydroxide (CH) in HVS/HVSFA pastes containing NS indicating the formation of additional calcium silicate hydrate (CSH) gels in the system. By combining slag, fly ash and NS in high volumes e.g. 70-80%, the carbon footprint of cement paste is reduced by 66-76% while maintains the similar compressive strength of control cement paste. Keywords: high volume slag, nanosilica, compressive strength, TGA, high volume slag-fly ash blend, CO2 emission.

Influence of Fly Ash on the Mechanical Properties of Engineered Cementitious Composites Cured at High Temperature

2010 ◽  
Vol 113-116 ◽  
pp. 1293-1296
Author(s):  
Yu Zhu ◽  
Ying Zi Yang ◽  
Hong Wei Deng ◽  
Yan Yao
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Fly Ash ◽  
High Volume ◽  
Bending Test ◽  
Cementitious Composites ◽  
Test Results ◽  
Four Point Bending ◽  
High Volume Fly Ash ◽  
Compressive Strength Test

In order to investigate the mechanical properties of cementitious composites (ECC) cured at 60°C, four-point bending test and compressive strength test are employed to analyze the effect of fly ash on the properties of ECC. The replacement ratio of cement with fly ash is 50%, 70% and 80%, respectively. The test results indicate that ECC with high volume fly ash still remain the characteristic of pseudo-strain hardening and the deflection of ECC increases remarkably by adding more fly ash. The observations of ECC indicate that the crack width is relatively smaller for higher volume fly ash ECC. Meanwhile, compressive strength of ECC specimens with 80% fly ash can reach to 70MPa. This is helpful to produce precast ECC with high volume of fly ash.

scholarly journals Effect of Copolymer Latexes on Physicomechanical Properties of Mortar Containing High Volume Fly Ash as a Replacement Material of Cement

2014 ◽  
Vol 2014 ◽  
pp. 1-11
Author(s):  
El-Sayed Negim ◽  
Latipa Kozhamzharova ◽  
Yeligbayeva Gulzhakhan ◽  
Jamal Khatib ◽  
Lyazzat Bekbayeva ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Compressive Strength ◽  
Fly Ash ◽  
Setting Time ◽  
High Volume ◽  
Physicomechanical Properties ◽  
Partial Replacement ◽  
Setting Times ◽  
High Volume Fly Ash ◽  
Scanning Electron

This paper investigates the physicomechanical properties of mortar containing high volume of fly ash (FA) as partial replacement of cement in presence of copolymer latexes. Portland cement (PC) was partially replaced with 0, 10, 20, 30 50, and 60% FA. Copolymer latexes were used based on 2-hydroxyethyl acrylate (2-HEA) and 2-hydroxymethylacrylate (2-HEMA). Testing included workability, setting time, absorption, chemically combined water content, compressive strength, and scanning electron microscopy (SEM). The addition of FA to mortar as replacement of PC affected the physicomechanical properties of mortar. As the content of FA in the concrete increased, the setting times (initial and final) were elongated. The results obtained at 28 days of curing indicate that the maximum properties of mortar occur at around 30% FA. Beyond 30% FA the properties of mortar reduce and at 60% FA the properties of mortar are lower than those of the reference mortar without FA. However, the addition of polymer latexes into mortar containing FA improved most of the physicomechanical properties of mortar at all curing times. Compressive strength, combined water, and workability of mortar containing FA premixed with latexes are higher than those of mortar containing FA without latexes.

scholarly journals Late Age Dynamic Strength of High-Volume Fly Ash Concrete with Nano-Silica and Polypropylene Fibres

Crystals ◽  
2020 ◽  
Vol 10 (4) ◽  
pp. 243 ◽  
Author(s):  
Mohamed H. Mussa ◽  
Ahmed M. Abdulhadi ◽  
Imad Shakir Abbood ◽  
Azrul A. Mutalib ◽  
Zaher Mundher Yaseen
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Elevated Temperatures ◽  
High Volume ◽  
Nano Silica ◽  
Polypropylene Fibres ◽  
Fly Ash Concrete ◽  
High Volume Fly Ash ◽  
Dynamic Compressive Strength ◽  
Curing Age

The dynamic behaviour of high-volume fly ash concrete with nano-silica (HVFANS) and polypropylene fibres at curing ages of 7 to 90 days was determined by using a split Hopkinson pressure bar (SHPB) machine. At each curing age, the concrete samples were laboratory tested at different temperatures conditions under strain rates reached up to 101.42 s−1. At room temperature, the results indicated that the dynamic compressive strength of plain concrete (PC) was slightly higher than HVFANS concrete at early curing ages of 7 and 28 days, however, a considerable improvement in the strength of HVFANS concrete was noted at a curing age of 90 days and recorded greater values than PC owing to the increase of fly ash reactivity. At elevated temperatures, the HVFANS concrete revealed a superior behaviour than PC even at early ages in terms of dynamic compressive strength, critical strain, damage and toughness due to increase of nano-silica (NS) activity during the heating process. Furthermore, equations were suggested to estimate the dynamic increase factor (DIF) of both concretes under the investigated factors.

scholarly journals Fire Resistance of High-Volume Fly Ash RC Slab Inclusion with Nano-Silica

Materials ◽  
2021 ◽  
Vol 14 (12) ◽  
pp. 3311
Author(s):  
Mohamed H. Mussa ◽  
Noor Azim Mohd Radzi ◽  
Roszilah Hamid ◽  
Azrul A. Mutalib
Keyword(s):  
Thermal Conductivity ◽  
Compressive Strength ◽  
Fly Ash ◽  
Concrete Slab ◽  
High Volume ◽  
Concrete Cover ◽  
Nano Silica ◽  
Load Curve ◽  
High Volume Fly Ash ◽  
Rc Slab

The study aims to investigate the fire performance of reinforced concrete (RC) slab fabricated from high volume fly ash inclusion with nano-silica (HVFANS) under ISO 834 load curve. The HVFANS concrete slab with dimensions of 1850 mm × 1700 mm × 200 mm was tested via an electrical furnace under an exposing temperature of 1100 °C for 120 min. The slab behaviour was evaluated in terms of residual compressive strength, temperature distribution along its thickness, spalling, and cracks. The results revealed that the slab was capable of maintaining 62.19% of its original compressive strength at room temperature after exposure to the above temperature. Moreover, the distribution of temperature revealed that the temperature of concrete cover and bottom reinforcement was less than 300 °C with a maximum spalling depth of 11 mm within the temperature range of 680 to 840 °C. Furthermore, the thermal conductivity index (K) of the HVFANS concrete was determined, and results indicated that thermal conductivity equalled 0.35 W/mK which is considered low, as compared with other concretes tested in current and previous studies.

scholarly journals Compressive Strength of High-Volume Fly Ash (HVFA) Concrete as a Function of Lime Water and Curing Time

2021 ◽  
Author(s):  
Chin Mei Yun ◽  
Md. Rezaur Rahman ◽  
Kuok King Kuok ◽  
Mohd Elfy Mersal ◽  
Colin Ngu Ker Liing ◽  
...  
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Portland Cement ◽  
High Volume ◽  
Partial Replacement ◽  
Curing Time ◽  
Additional Information ◽  
Lime Water ◽  
High Volume Fly Ash

Abstract The compressive strength of high-volume fly ash (HVFA) concrete with varied volume percentages of 40%, 50%, and 60% was examined utilizing low calcium fly ash (Class-F) as a partial replacement for regular Portland cement in this study. On the 7th, 28th, and 56th days, the compressive strength is tested. At the 7th and 28th days, the influence of saturated lime water on the compressive strength of HVFA concrete is evaluated. The inclusion of fly ash as a replacement for Portland cement reduces the compressive strength of the HVFA concrete, according to the findings. At the 56th day, the HVFA concrete with 40% fly ash substitution has a compressive strength equivalent to the regular weight concrete. At the 28th day, it was discovered that saturated lime water was helpful in maximizing the strength of HVFA concrete with 50% fly ash substitution. There was additional information about the characterization of HVFA concrete.

Sign in / Sign up

Export Citation Format

Share Document