Diminishing Shape Errors at Electrical Discharge Machining of External Cylindrical Surfaces

2013 ◽  
Vol 371 ◽  
pp. 305-309 ◽  
Author(s):  
Laurenţiu Slătineanu ◽  
Margareta Coteaţă ◽  
Lorelei Gherman ◽  
Irina Beşliu ◽  
Miroslav Radovanović ◽  
...  
Keyword(s):  
Experimental Observation ◽  
Electrical Discharge ◽  
Electrical Discharge Machining ◽  
Cylindrical Tube ◽  
Tool Electrode ◽  
Shape Error ◽  
Machined Surface ◽  
Shape Errors ◽  
Cylindrical Parts ◽  
Experimental Researches

Electrical discharge machining is a method that could be applied in order to detach cylindrical parts from a workpiece made of electroconductive material. If cylindrical tube is used as tool electrode, the machined surface could have a conical shape, due to the presence in the work gap of the electroconductive particles, detached from electrodes. Experimental researches were developed in order to obtain information concerning the shape error of machined surface. As a result of the experimental observation, improved technological solutions were identified and investigated. The experimental results proved certain possibilities of shape error decrease.

Machining of External Cylindrical Surfaces on a RAM Electrical Discharge Machine

2013 ◽  
Vol 554-557 ◽  
pp. 1800-1805 ◽  
Author(s):  
Laurenţiu Slătineanu ◽  
Margareta Coteaţă ◽  
Irina Besliu ◽  
Lorelei Gherman ◽  
Oana Dodun
Keyword(s):  
Test Piece ◽  
Electrical Discharge ◽  
Electrical Discharge Machining ◽  
Electrical Discharge Machine ◽  
Machining Process ◽  
Tool Electrode ◽  
Shape Error ◽  
Machined Surface ◽  
Electrode Tool ◽  
Shape Errors

As other nonconventional machining methods, the electrical discharge machining is applied when the workpieces materials are difficult to be machined by classical machining methods or the surfaces could not be obtained in efficient conditions by classical machining methods. Such a situation could appear, for example, when test pieces must be separated from materials whose machining by classical methods is difficult. Taking into consideration the necessity to detach a cylindrical test piece from a workpiece made of a high resistance metallic alloy, the problem of using the electrical discharge machining was formulated. An initial experimental test by using the common work motion of the tool electrode from up to down highlighted high shape errors, due to the accumulation in the work zone of the particles detached from the workpiece and from the tool electrode, as a consequence of electrical discharge machining process. A second set of experiments were developed, placing the test piece over the electrode tool and ensuring a work motion of workpiece from up to down; in this situation, a diminishing of the shape error was noticed. The second set of experiments highlighted a relatively reduced conicalness of the machined surface and a low decrease of the machining speed. as the penetration depth of the tool electrode in the workpiece increases, too.

scholarly journals Experiments of ultrasonically aided micro-EDM on Ti with nanostructured superficial TiO2 layers

2018 ◽  
Vol 178 ◽  
pp. 03010
Author(s):  
Niculae Marinescu ◽  
Daniel Ghiculescu ◽  
Stergios Ganatsios ◽  
George Seritan
Keyword(s):  
Electrical Discharge ◽  
Electrical Discharge Machining ◽  
Nanotube Arrays ◽  
Micro Edm ◽  
X Rays ◽  
Machined Surface ◽  
Advanced Material ◽  
Titania Nanotube Arrays ◽  
Experimental Researches ◽  
Scanning Electron

The paper deals with experimental researches concerning micromachining through ultrasonically aided electrical discharge machining (μEDM+US) of an advanced material, comprising a base metal from Ti and superficial nanometric layers from TiO2, i.e. Titania nanotube arrays. The material was investigated by scanning electron microscope. The chemical composition of machined samples was determined by X rays spectrometer energy dispersive. The roughness of machined surface was studied using a profile surface instrument. A comparison was made between the results obtained by classic μEDM and μEDM+US in terms of surface roughness, and craters microgeometry.

Ti-6Al-4V Surfaces in SiC Powder Mixed Electrical Discharge Machining

2013 ◽  
Vol 856 ◽  
pp. 226-230 ◽  
Author(s):  
Hamidullah Yaşar ◽  
Bülent Ekmekci
Keyword(s):  
Electrical Discharge ◽  
Electrical Discharge Machining ◽  
Dielectric Liquid ◽  
Operational Parameters ◽  
Electrical Parameters ◽  
Machined Surface ◽  
Optical Scanning ◽  
Surface Topographies ◽  
Powder Suspension

The role of suspended particles on Ti-6Al-4V surface in Powder Mixed Electrical Discharge Machining (PMEDM) is studied using SiC powder mixing in water dielectric liquid. Surface modifications due to the additives in dielectric liquid are investigated by means of optical, scanning electron microscopy and energy dispersive spectroscopy. The attachment of added powders and surface topographies interrelated with powder suspension concentration, particle size and electrical parameters such as pulse on duration and current. The influence on discharge transitivity with respect to SiC additives is noticed with pock like features on the surface. The geometry and size of these features indicated a robust dependency with respect to operational parameters and indicated the role of secondary discharges during PMEDM. SiC particles severely transferred from di-electric liquid to machined surface at critical operational parameters and implied that the process could be also used as a surface alloying technique.

scholarly journals Sub-Microstructure of Surface and Subsurface Layers after Electrical Discharge Machining Structural Materials in Water

Metals ◽  
2021 ◽  
Vol 11 (7) ◽  
pp. 1040
Author(s):  
Sergey N. Grigoriev ◽  
Marina A. Volosova ◽  
Anna A. Okunkova ◽  
Sergey V. Fedorov ◽  
Khaled Hamdy ◽  
...  
Keyword(s):  
Electrical Discharge ◽  
Electrical Discharge Machining ◽  
Structural Materials ◽  
12Kh18n10t Steel ◽  
Mean Deviation ◽  
Water Medium ◽  
Tool Electrode ◽  
Marquardt Algorithm ◽  
Subsurface Layers ◽  
Electrical Wear

The material removal mechanism, submicrostructure of surface and subsurface layers, nanotransformations occurred in surface and subsurface layers during electrical discharge machining two structural materials such as anti-corrosion X10CrNiTi18-10 (12kH18N10T) steel of austenite class and 2024 (D16) duralumin in a deionized water medium were researched. The machining was conducted using a brass tool of 0.25 mm in diameter. The measured discharge gap is 45–60 µm for X10CrNiTi18-10 (12kH18N10T) steel and 105–120 µm for 2024 (D16) duralumin. Surface roughness parameters are arithmetic mean deviation (Ra) of 4.61 µm, 10-point height (Rz) of 28.73 µm, maximum peak-to-valley height (Rtm) of 29.50 µm, mean spacing between peaks (Sm) of 18.0 µm for steel; Ra of 5.41 µm, Rz of 35.29 µm, Rtm of 43.17 µm, Sm of 30.0 µm for duralumin. The recast layer with adsorbed components of the wire tool electrode and carbides was observed up to the depth of 4–6 µm for steel and 2.5–4 µm for duralumin. The Levenberg–Marquardt algorithm was used to mathematically interpolate the dependence of the interelectrode gap on the electrical resistance of the material. The observed microstructures provide grounding on the nature of electrical wear and nanomodification of the obtained surfaces.

Effect of Arc Discharge Pressure on Discharge Current in EDM

2008 ◽  
Vol 381-382 ◽  
pp. 451-454
Author(s):  
Atsutoshi Hirao ◽  
S. Tai ◽  
H. Takezawa ◽  
Naotake Mohri ◽  
Kazuro Kageyama ◽  
...  
Keyword(s):  
Discharge Current ◽  
Electrical Discharge ◽  
Material Removal ◽  
Electrical Discharge Machining ◽  
Arc Discharge ◽  
Vibration Sensor ◽  
Work Piece ◽  
Tool Electrode ◽  
Discharge Pressure ◽  
Current Behavior

In electrical discharge machining (EDM), an electrical discharge occurs between a tool electrode and a work-piece, and removal of materials is carried out by vaporized explosion between the electrode and the work-piece. However, the mechanism of material removal in EDM is not well understood. In order to clarify this issue, the acoustic emission (AE) method has been applied to examine the force of explosion, and the Schlieren visualization method has been applied to observe the explosion. In this study, we investigate the effect of discharge current behavior on the occurrence of the AE waves by means of an optical fiber vibration sensor.

Analysis of Dimensional Accuracy (Over Cut) and Surface Quality (Roughness) in Electrical Discharge Machining of Inconel-718 Alloy

2019 ◽  
Vol 969 ◽  
pp. 644-649
Author(s):  
Rakesh Kumar ◽  
Anand Pandey ◽  
Pooja Sharma
Keyword(s):  
Inconel 718 ◽  
Electrical Discharge ◽  
Electrical Discharge Machining ◽  
Dimensional Accuracy ◽  
Work Piece ◽  
Tool Electrode ◽  
Affecting Factors ◽  
Inconel 718 Alloy ◽  
Electrical Discharge Drilling ◽  
Pulse On Time

Inconel-718 is a nickel based super alloy (difficult-to-cut material) used in aerospace industry. Analysis of machining performances viz. Over Cut (OC) & Surface Roughness (SR) for Inconel-718 through rotary Cu-pin tool electrode have been carried out. Peak current (Ip), pulse-on time (Ton), tool rotation (Nt) & hole depth (h) were used as input factors in Electrical Discharge Drilling (EDD) of Inconel-718 work-piece. Effect of input parameters on performance characteristics like OC & SR were found by Taguchi’s L9 (34) orthogonal array. It is reveals that Ip & h are most affecting factors that affects OC & SR. The Scanning Electron Microscope image was used to measure diameter of hole on work-piece after machining.

scholarly journals Comparative Study of Flank Cams Manufactured by WEDM and Milling Processes

Metals ◽  
2020 ◽  
Vol 10 (9) ◽  
pp. 1159
Author(s):  
Irene Buj-Corral ◽  
Enrique Zayas-Figueras ◽  
Àngels Montaña-Faiget
Keyword(s):  
Electrical Discharge ◽  
Electrical Discharge Machining ◽  
Combustion Engine ◽  
Computer Assisted ◽  
Geometrical Parameters ◽  
Wire Electrical Discharge Machining ◽  
Shape Error ◽  
Fused Filament Fabrication ◽  
Cam Follower ◽  
Contour Surface

Cam-follower mechanisms are usually employed in different machines, like combustion engines, sewing machines, machine tools, etc. In the present paper, the option to manufacture cams utilizing wire electrical discharge machining (WEDM) has been considered. For this, surface roughness and shape error of cam profiles manufactured by the processes of milling and wire electrical discharge machining (WEDM) are presented. The methodology used covers different stages: design, prototyping, manufacturing, and measurement of the cams. As a reference, a cam-follower mechanism from a motorcycle internal combustion engine has been used. A reverse engineering process has been performed to determine the geometrical parameters of the mechanism, which are used for the synthesis of the profile of the cam and its subsequent design. The manufacturing process of the cams has been assisted by CAD-CAM (Computer Assisted Drawing-Computer Assisted Manufacturing) software. Using fused filament fabrication (FFF), a physical prototype of the cam has been manufactured, in order to validate the goodness of the design. Finally, the roughness and shape parameters have been measured on the contour surface of the cams. The arithmetical mean roughness Ra value of the milled cam was 0.269 μm, below the requirement of 0.4 μm, and shape error was 18 μm, below 50 μm. Shape error of the WEDM cam of 48 μm meets the requirements for cams. However, the Ra value of 1.212 μm, exceeded the limit. For this reason, a finish operation is recommended in this case. Some advantages of WEDM cams over milled cams are that different conductive materials can be employed, more complex shapes can be obtained, and that, in rough operations, the amount of material to be removed in subsequent operations is considerably reduced.

Modeling of Recast Layer in Micro-Electrical Discharge Machining

2010 ◽  
Vol 132 (3) ◽  
Author(s):  
P. C. Tan ◽  
S. H. Yeo
Keyword(s):  
Numerical Model ◽  
Electrical Discharge ◽  
Prediction Models ◽  
Electrical Discharge Machining ◽  
Performance Measure ◽  
Recast Layer ◽  
Micro Edm ◽  
Machined Surface ◽  
Functional Layer ◽  
Pulse On Time

The thickness of recast layers produced during electrical discharge machining (EDM) is an important process performance measure as it may indicate an extent of crack propagation in a machined surface or thickness of a functional layer alloyed onto a machined surface. Thus, the availability of the recast layer thickness prediction models is needed to allow better control of machining outcomes, which becomes more vital for micro-EDM due to the microscale of machined features. The proposed numerical model, based on a multiple discharge approach for recast layer prediction, is developed to fill an existing gap in micro-EDM. The multiple discharge approach accounts for the overlapping nature by which craters are generated on the machined surface and considers the recast layer to be a combination of individual recast regions from individual craters. The numerical analysis, based on finite element methods, is used to determine the melting isotherms due to heat inputs on overlapping crater profiles. Then, a hemispherical-capped crater profile is estimated by applying a recast plasma flushing efficiency to the amount of molten material bounded by the melting isotherm. Finally, the recast region is defined to be bounded by the melting isotherm and crater profile. The model, developed for a peak discharge current of 1.45 A and pulse on time between 166 ns and 606 ns, predicted recast layer thicknesses of between 1.0 μm and 1.82 μm. It is then validated at pulse on time settings of 244 ns and 458 ns, which generated average recast layer thicknesses of 1.18 μm and 1.56 μm, respectively. Thus, the numerical model developed using the multiple discharge approach is suitable for estimation of recast layer thicknesses in micro-EDM.

Sign in / Sign up

Export Citation Format

Share Document