The Research on Pure Water Hydraulic External Gear Pump

2010 ◽  
Vol 44-47 ◽  
pp. 1767-1772
Author(s):  
De Xin Zhao ◽  
Rui Bo Yuan ◽  
Jing Luo
Keyword(s):  
Surface Treatment ◽  
Structural Design ◽  
Treatment Process ◽  
Pure Water ◽  
Spare Part ◽  
Gear Pump ◽  
Calculation Of Parameters ◽  
Water Hydraulic ◽  
Engineering Materials ◽  
External Gear Pump

This article describes the structure of pure water hydraulic external gear pump, structural design and calculation of parameters,analysises the mai spare part material of pure water hydraulic external gear pump and determines the type of the new engineering materials. Besides the surface treatment process of pump are discussed. Pure water hydraulic external gear pump is simulated by FLUENT, obtaining the parameters of the influence of the pump's performance.

scholarly journals Parameterization, Modeling, and Validation in Real Conditions of an External Gear Pump

2021 ◽  
Vol 13 (6) ◽  
pp. 3089
Author(s):  
Miquel Torrent ◽  
Pedro Javier Gamez-Montero ◽  
Esteban Codina
Keyword(s):  
Working Conditions ◽  
Test Bench ◽  
Fluid Dynamic ◽  
Graph Model ◽  
Field Tests ◽  
Black Box ◽  
Gear Pump ◽  
Volumetric Behavior ◽  
External Gear Pump ◽  
Standard Tests

This article presents a methodology for predicting the fluid dynamic behavior of a gear pump over its operating range. Complete pump parameterization was carried out through standard tests, and these parameters were used to create a bond graph model to simulate the behavior of the unit. This model was experimentally validated under working conditions in field tests. To carry this out, the pump was used to drive the auxiliary movements of a drilling machine, and the experimental data were compared with a simulation of the volumetric behavior under the same conditions. This paper aims to describe a method for characterizing any hydrostatic pump as a “black box” model predicting its behavior in any operating condition. The novelty of this method is based on the correspondence between the variation of the parameters and the internal changes of the unit when working in real conditions, that is, outside a test bench.

scholarly journals The Hybrid Process of Low-Pressure Carburizing and Metallization (Cr + LPC, Al + LPC) of 17CrNiMo7-6 and 10NiCrMo13-5 Steels

Coatings ◽  
2021 ◽  
Vol 11 (5) ◽  
pp. 567
Author(s):  
Paulina Kowalczyk ◽  
Konrad Dybowski ◽  
Bartłomiej Januszewicz ◽  
Radomir Atraszkiewicz ◽  
Marcin Makówka
Keyword(s):  
Corrosion Resistance ◽  
Surface Layer ◽  
Physicochemical Properties ◽  
Surface Treatment ◽  
Retained Austenite ◽  
Treatment Process ◽  
Active Surface ◽  
Low Pressure ◽  
Low Alloy Steel ◽  
Chromium Plating

This paper presents the concept of modification of physicochemical properties of steels by simultaneous diffusion saturation with carbon and chromium or aluminum. The application of a hybrid surface treatment process consisting of a combination of aluminizing and low-pressure carburizing (Al + LPC) resulted in a reduction in the amount of retained austenite in the surface layer of the steel. While the use of chromium plating and low-pressure carburizing (Cr + LPC) induced an improvement in the corrosion resistance of the carburized steels. It is of particular importance in case of vacuum processes after the application of which the active surface corrodes easily, as well as in case of carburizing of low-alloy steel with nickel, where an increased content of retained austenite in the surface layer is found after carburizing.

Computer Prediction of Cyclic Excitation Sources for an External Gear Pump

1985 ◽  
Vol 199 (3) ◽  
pp. 175-180 ◽  
Author(s):  
K Foster ◽  
R Taylor ◽  
I M Bidhendi
Keyword(s):  
Computer Program ◽  
Gear Pump ◽  
Computer Prediction ◽  
Pressure Distributions ◽  
External Gear Pumps ◽  
Theoretical Predictions ◽  
Gear Pumps ◽  
External Gear Pump

A description is given of a computer program for investigating the performance of the external gear pumps under varying conditions with the special emphasis on the examination of pressure distributions within the pump, i.e. excitation forces for the vibration of the pump case and the variation in flow generated by the pump. Measurements are presented for the variation with time of tooth space pressure and the results are compared with the theoretical predictions from the computer program.

Surface treatment process applicable to next generation graphene-based electronics

Carbon ◽  
2016 ◽  
Vol 104 ◽  
pp. 119-124 ◽  
Author(s):  
Ki Seok Kim ◽  
Hyo-Ki Hong ◽  
Hanearl Jung ◽  
Il-Kwon Oh ◽  
Zonghoon Lee ◽  
...  
Keyword(s):  
Surface Treatment ◽  
Treatment Process ◽  
Next Generation

Experimental Investigation of Flowrate Irregularity in Rotary Gear Pumps

1992 ◽  
Author(s):  
G. Mimmi
Keyword(s):  
Experimental Investigation ◽  
Flow Rate ◽  
Experimental Tests ◽  
Periodic Variation ◽  
Experimental Results ◽  
Gear Pump ◽  
Gear Pumps ◽  
Hot Film ◽  
Instantaneous Flow Rate ◽  
External Gear Pump

Abstract In a previous paper the author proposed a method to reduce the periodic variation in flow rate for an external gear pump. To verify the experimental results, a series of experimental tests on a expressly realized gear pump, was carried out. The pump was equipped with relieving grooves milled into the side plates. The tests were done on a closed piping specifically realized and equipped for measuring the instantaneous flow rate of the fluid through a wedge-shaped hot film probe.

Sign in / Sign up

Export Citation Format

Share Document