Simulation Study of Steam-Flooding Mechanisms and Influence Factors in Light-Oil Reservoirs after Water-Flooding

2014 ◽  
Vol 508 ◽  
pp. 165-168
Author(s):  
Qing Jie Gu
Keyword(s):  
Oil Recovery ◽  
Simulation Study ◽  
Enhanced Recovery ◽  
Influence Factors ◽  
Oil Reservoirs ◽  
Water Flooding ◽  
Steam Flooding ◽  
Heavy Oil Reservoirs ◽  
Light Oil ◽  
Light Oil Reservoirs

Steam-flooding, the most successful among enhanced recovery methods, has been applied mainly to heavy-oil reservoirs. And it is still in its infancy on light-oil reservoirs at present. This paper will take the oil-water transition zone in Saertu oilfield for example, presents a comprehensive simulation study on the use of steam-flooding after water-flood in light-oil reservoirs. Some important observations are made on this new application of the process. Relative importance of key mechanisms to oil recovery is also discussed. Guidelines are developed not only for selecting reservoir candidates for steam-flooding, but also for the factors which will effect the oil recovery in steam-flooding performance.

The Mechanism of Flue Gas Injection for Enhanced Light Oil Recovery

2004 ◽  
Vol 126 (2) ◽  
pp. 119-124 ◽  
Author(s):  
O. S. Shokoya ◽  
S. A. (Raj) Mehta ◽  
R. G. Moore ◽  
B. B. Maini ◽  
M. Pooladi-Darvish ◽  
...  
Keyword(s):  
Oil Recovery ◽  
Flue Gas ◽  
Gas Injection ◽  
Cost Effective ◽  
Air Injection ◽  
Oil Reservoirs ◽  
Flue Gases ◽  
Low Permeability ◽  
Light Oil ◽  
Light Oil Reservoirs

Flue gas injection into light oil reservoirs could be a cost-effective gas displacement method for enhanced oil recovery, especially in low porosity and low permeability reservoirs. The flue gas could be generated in situ as obtained from the spontaneous ignition of oil when air is injected into a high temperature reservoir, or injected directly into the reservoir from some surface source. When operating at high pressures commonly found in deep light oil reservoirs, the flue gas may become miscible or near–miscible with the reservoir oil, thereby displacing it more efficiently than an immiscible gas flood. Some successful high pressure air injection (HPAI) projects have been reported in low permeability and low porosity light oil reservoirs. Spontaneous oil ignition was reported in some of these projects, at least from laboratory experiments; however, the mechanism by which the generated flue gas displaces the oil has not been discussed in clear terms in the literature. An experimental investigation was carried out to study the mechanism by which flue gases displace light oil at a reservoir temperature of 116°C and typical reservoir pressures ranging from 27.63 MPa to 46.06 MPa. The results showed that the flue gases displaced the oil in a forward contacting process resembling a combined vaporizing and condensing multi-contact gas drive mechanism. The flue gases also became near-miscible with the oil at elevated pressures, an indication that high pressure flue gas (or air) injection is a cost-effective process for enhanced recovery of light oils, compared to rich gas or water injection, with the potential of sequestering carbon dioxide, a greenhouse gas.

scholarly journals Evaluation of Cyclic Gas Injection in Enhanced Recovery from Unconventional Light Oil Reservoirs: Effect of Gas Type and Fracture Spacing

Energies ◽  
2019 ◽  
Vol 12 (7) ◽  
pp. 1370 ◽  
Author(s):  
Assef ◽  
Almao
Keyword(s):  
Hydraulic Fracturing ◽  
Enhanced Recovery ◽  
Gas Injection ◽  
Oil Reservoirs ◽  
Low Permeability ◽  
Fracture Spacing ◽  
Light Oil ◽  
Light Oil Reservoirs

ultra-low permeability; hydraulic fracturing; cyclical gas injection; fracking stages

A New High-Temperature Gel for Profile Control in Heavy Oil Reservoirs

2015 ◽  
Vol 138 (2) ◽  
Author(s):  
Changjiu Wang ◽  
Huiqing Liu ◽  
Qiang Zheng ◽  
Yongge Liu ◽  
Xiaohu Dong ◽  
...  
Keyword(s):  
High Temperature ◽  
Oil Recovery ◽  
Heavy Oil ◽  
Three Dimensional ◽  
Heat Stability ◽  
Steam Injection ◽  
Oil Reservoirs ◽  
Steam Flooding ◽  
Profile Control ◽  
Heavy Oil Reservoirs

Controlling the phenomenon of steam channeling is a major challenge in enhancing oil recovery of heavy oil reservoirs developed by steam injection, and the profile control with gel is an effective method to solve this problem. The use of conventional gel in water flooding reservoirs also has poor heat stability, so this paper proposes a new high-temperature gel (HTG) plugging agent on the basis of a laboratory experimental investigation. The HTG is prepared with nonionic filler and unsaturated amide monomer (AM) by graft polymerization and crosslinking, and the optimal gel formula, which has strong gelling strength and controllable gelation time, is obtained by the optimization of the concentration of main agent, AM/FT ratio, crosslinker, and initiator. To test the adaptability of the new HTG to heavy oil reservoirs and the performance of plugging steam channeling path and enhancing oil recovery, performance evaluation experiments and three-dimensional steam flooding and gel profile control experiments are conducted. The performance evaluation experiments indicate that the HTG has strong salt resistance and heat stability and still maintains strong gelling strength after 72 hrs at 200 °C. The singular sand-pack flooding experiments suggest that the HTG has good injectability, which can ensure the on-site construction safety. Moreover, the HTG has a high plugging pressure and washing out resistance to the high-temperature steam after gel forming and keeps the plugging ratio above 99.8% when the following steam injected volume reaches 10 PV after gel breakthrough. The three-dimensional steam flooding and gel profile control experiments results show that the HTG has good plugging performance in the steam channeling path and effectively controls its expanding. This forces the following steam, which is the steam injected after the gelling of HTG in the model, to flow through the steam unswept area, which improves the steam injection profile. During the gel profile control period, the cumulative oil production increases by 294.4 ml and the oil recovery is enhanced by 8.4%. Thus, this new HTG has a good effect in improving the steam injection profile and enhancing oil recovery and can be used to control the steam channeling in heavy oil reservoirs.

Sign in / Sign up

Export Citation Format

Share Document