Modeling and Numerical Simulation for the Newly Designed Four Cavity Blades Vertical Axis Wind Turbine

2014 ◽  
Vol 554 ◽  
pp. 536-540
Author(s):  
Kadhim Suffer ◽  
Ryspek Usubamatov ◽  
Ghulam Abdul Quadir ◽  
Khairul Azwan Ismail
Keyword(s):  
Wind Turbine ◽  
Wind Turbines ◽  
Urban Areas ◽  
Fluid Dynamic ◽  
Turbulence Models ◽  
Vertical Axis ◽  
Vertical Axis Wind Turbine ◽  
Vertical Axis Wind Turbines ◽  
Horizontal Axis Wind Turbines ◽  
The Individual

The last years have proved that Vertical Axis Wind Turbines (VAWTs) are more suitable for urban areas than Horizontal Axis Wind Turbines (HAWTs). To date, very little has been published in this area to assess good performance and lifetime of VAWTs either in open or urban areas. The main goal of this current research is to investigate numerically the aerodynamic performance of a newly designed cavity type vertical axis wind turbine having four blades. In the current new design the power generated depends on the drag force generated by the individual blades and interactions between them in a rotating configuration. For numerical investigation, commercially available computational fluid dynamic CFD software GAMBIT and FLUENT were used. In this numerical analysis the Shear Stress Transport (SST) k-ω turbulence model is used which is better than the other turbulence models available as suggested by some researchers. The computed results show good agreement with published experimental results.

Numerical Simulation for the Aerodynamics of Vertical Axis Wind Turbine with Two Different Rotors Having Movable Vanes

2015 ◽  
Vol 786 ◽  
pp. 205-209 ◽  
Author(s):  
H.S. Kadhim ◽  
G.A. Quadir ◽  
A.K. Farhan ◽  
U. Ryspek ◽  
K.A. Ismail
Keyword(s):  
Numerical Simulation ◽  
Wind Turbines ◽  
Urban Areas ◽  
Fluid Dynamic ◽  
Turbulence Models ◽  
Vertical Axis ◽  
Vertical Axis Wind Turbine ◽  
Horizontal Axis Wind Turbines ◽  
Present Design ◽  
The Individual

Wind energy has seen a rapid growth worldwide. Wind turbines are typical devices that convert the kinetic energy of wind into electricity. Researches in the past have proved that Vertical Axis Wind Turbines (VAWTs) are more suitable for urban areas than Horizontal Axis Wind Turbines (HAWTs). In the present design of the VAWT, the power prodused depends on the drag force generated by the individual blades and interactions between them in a rotating configuration. Numerical simulation for the aerodynamics of VAWT with tow different rotors (Three and Foure blades ) having movable vanes are curred out. The For numerical simulation, commercially available computational fluid dynamic (CFD) softwares GAMBIT and FLUENT are used. In this work the Shear Stress Transport (SST) k-ω turbulence model was used which is better than the other turbulence models available as suggested by some researchers. The predicted results show agreement with those reported in the literature for VAWT having different blades designs.

Vertical axis wind turbine operation in icing conditions: A review study

2021 ◽  
pp. 0309524X2110618
Author(s):  
Syed Abdur Rahman Tahir ◽  
Muhammad Shakeel Virk
Keyword(s):  
Wind Turbine ◽  
Wind Turbines ◽  
Vertical Axis ◽  
Electricity Production ◽  
Vertical Axis Wind Turbine ◽  
Vertical Axis Wind Turbines ◽  
Horizontal Axis Wind Turbines ◽  
Promising Solution ◽  
Review Study ◽  
Accretion Physics

Vertical Axis Wind Turbine (VAWT) can be a promising solution for electricity production in remote ice prone territories of high north, where good wind resources are available, but icing is a challenge that can affect its optimum operation. A lot of research has been made to study the icing effects on the conventional horizontal axis wind turbines, but the literature about vertical axis wind turbines operating in icing conditions is still scarce, despite the importance of this topic. This paper presents a review study about existing knowledge of VAWT operation in icing condition. Focus has been made in better understanding of ice accretion physics along VAWT blades and methods to detect and mitigate icing effects.

Aerodynamic Measurements on a Vertical Axis Wind Turbine in a Large Scale Wind Tunnel

2010 ◽  
Author(s):  
L. Battisti ◽  
L. Zanne ◽  
S. Dell’Anna ◽  
V. Dossena ◽  
B. Paradiso ◽  
...  
Keyword(s):  
Wind Tunnel ◽  
Flow Field ◽  
Wind Turbine ◽  
Wind Turbines ◽  
Large Scale ◽  
Fluid Dynamic ◽  
Vertical Axis ◽  
Vertical Axis Wind Turbine ◽  
Aerodynamic Optimization ◽  
Vertical Axis Wind Turbines

This paper presents the first results of a wide experimental investigation on the aerodynamics of a vertical axis wind turbine. Vertical axis wind turbines have recently received particular attention, as interesting alternative for small and micro generation applications. However, the complex fluid dynamic mechanisms occurring in these machines make the aerodynamic optimization of the rotors still an open issue and detailed experimental analyses are now highly recommended to convert improved flow field comprehensions into novel design techniques. The experiments were performed in the large-scale wind tunnel of the Politecnico di Milano (Italy), where real-scale wind turbines for micro generation can be tested in full similarity conditions. Open and closed wind tunnel configurations are considered in such a way to quantify the influence of model blockage for several operational conditions. Integral torque and thrust measurements, as well as detailed aerodynamic measurements were applied to characterize the 3D flow field downstream of the turbine. The local unsteady flow field and the streamwise turbulent component, both resolved in phase with the rotor position, were derived by hot wire measurements. The paper critically analyses the models and the correlations usually applied to correct the wind tunnel blockage effects. Results evidence that the presently available theoretical correction models does not provide accurate estimates of the blockage effect in the case of vertical axis wind turbines. The tip aerodynamic phenomena, in particular, seem to play a key role for the prediction of the turbine performance; large-scale unsteadiness is observed in that region and a simple flow model is used to explain the different flow features with respect to horizontal axis wind turbines.

scholarly journals Fabrication and Performance Evaluation of Savonious Vertical Axis Wind Turbine for Uncertain Speed Regions

2017 ◽  
Vol 13 (2) ◽  
Keyword(s):  
Performance Evaluation ◽  
Wind Turbine ◽  
Wind Turbines ◽  
Urban Areas ◽  
Vertical Axis ◽  
Design Parameters ◽  
Vertical Axis Wind Turbine ◽  
Horizontal Axis Wind Turbine ◽  
Vertical Axis Wind Turbines ◽  
And Performance

The consumption of electricity in urban as well as rural is increasing every day and became an essential commodity for household and industrial purposes. Unfortunately the availability of electrical energy in India is not sufficient to the required demand and it is essential to discover and generate energy from non-conventional sources with cheap cost. On the same time it is necessary to reduce the consumption of conventional sources and to save fuel. Among all the renewable resources, wind is one of the best resources available all the time at free of cost. Especially vertical axis wind turbines (VAWT) are self-starting, omni directional. They require no yaw mechanism to continuously orient towards the wind direction and provide a more reliable energy conversion technology, as compared to horizontal axis wind turbine. Particularly savonius vertical axis wind turbines (SVAWT) are suitable and practically possible at low or uncertain wind speed regimes. They can be fitted on rooftops and also suitable for the urban areas where electricity is not available properly. This project deals with the fabrication and performance evaluation of savonius vertical axis wind turbine using two blade rotor. The amount of power developed by the wind turbine is calculated under theoretical and practical conditions and aerodynamics coefficients are also estimated. And various design parameters of savonious rotor are identified and determined.

Adaptive surface distortions for torque ripple control in vertical-axis wind turbines

2019 ◽  
pp. 0309524X1987402 ◽  
Author(s):  
Gareth Erfort ◽  
Theodor W von Backström ◽  
Gerhard Venter
Keyword(s):  
Wind Turbine ◽  
Wind Turbines ◽  
Fluid Dynamic ◽  
Vertical Axis ◽  
Torque Ripple ◽  
Small Scale ◽  
Blade Design ◽  
Vertical Axis Wind Turbine ◽  
Horizontal Axis Wind Turbine ◽  
Vertical Axis Wind Turbines

Vertical-axis wind turbines have been confined to small-scale generation in urban environments where their omnidirectional capability offers them an advantage over the more ubiquitous horizontal-axis wind turbine. With a drive towards renewable energy, more opportunities exist for the implementation of wind turbines in a multitude of environments. Based on its inherent operational drawbacks, the vertical-axis wind turbine has not undergone extensive investigation. Recently, there has been a resurgence of interest in the technology. This article addresses the torque ripple, a variation in torque produced by the turbine, present during operation. The variation in torque generated by a vertical-axis wind turbine increases the likelihood of failure due to fatigue. Current treatment is symptomatic and addresses the result of the torque fluctuation and not the cause. A novel blade design, capable of altering the lift and drag response through shape alteration, is presented as a solution. The blade design and operation is achieved through genetic algorithm optimization and computational fluid dynamic simulations. Comparisons with previous work show the novel blade presented here surpasses the reduction seen with pitching solutions. A 25% reduction in torque ripple was demonstrated for a 17% reduction in performance coefficient using the surface distortion approach. This surpasses the foil pitching approach which achieved a 15% torque ripple reduction for the same loss in performance coefficient.

Aerodynamic Measurements on a Vertical Axis Wind Turbine in a Large Scale Wind Tunnel

2011 ◽  
Vol 133 (3) ◽  
Author(s):  
L. Battisti ◽  
L. Zanne ◽  
S. Dell’Anna ◽  
V. Dossena ◽  
G. Persico ◽  
...  
Keyword(s):  
Wind Tunnel ◽  
Flow Field ◽  
Wind Turbine ◽  
Wind Turbines ◽  
Large Scale ◽  
Fluid Dynamic ◽  
Vertical Axis ◽  
Vertical Axis Wind Turbine ◽  
Aerodynamic Optimization ◽  
Vertical Axis Wind Turbines

This paper presents the first results of a wide experimental investigation on the aerodynamics of a vertical axis wind turbine. Vertical axis wind turbines have recently received particular attention, as interesting alternative for small and micro generation applications. However, the complex fluid dynamic mechanisms occurring in these machines make the aerodynamic optimization of the rotors still an open issue and detailed experimental analyses are now highly recommended to convert improved flow field comprehensions into novel design techniques. The experiments were performed in the large-scale wind tunnel of the Politecnico di Milano (Italy), where real-scale wind turbines for micro generation can be tested in full similarity conditions. Open and closed wind tunnel configurations are considered in such a way to quantify the influence of model blockage for several operational conditions. Integral torque and thrust measurements, as well as detailed aerodynamic measurements were carried out to characterize the 3D flow field downstream of the turbine. The local unsteady flow field and the streamwise turbulent component, both resolved in phase with the rotor position, were derived by hot wire measurements. The paper critically analyses the models and the correlations usually applied to correct the wind tunnel blockage effects. Results highlight that the presently available theoretical correction models do not provide accurate estimates of the blockage effect in the case of vertical axis wind turbines. The tip aerodynamic phenomena, in particular, seem to play a key role for the prediction of the turbine performance; large-scale unsteadiness is observed in that region and a simple flow model is used here to explain the different flow features with respect to horizontal axis wind turbines.

scholarly journals Aerodynamic improvement of Darrieus wind turbine

2021 ◽  
Vol 897 (1) ◽  
pp. 012001
Author(s):  
Oleg Goman ◽  
Andrii Dreus ◽  
Anton Rozhkevych ◽  
Krystyna Heti
Keyword(s):  
Reynolds Number ◽  
Wind Turbine ◽  
Wind Turbines ◽  
Structural Reliability ◽  
Vertical Axis ◽  
Vertical Wind ◽  
Integral Approach ◽  
Vertical Axis Wind Turbine ◽  
Calculation Algorithm ◽  
Vertical Axis Wind Turbines

Abstract Until recently, vertical-axis wind turbines are less extensively developed in wind energetics. At the same time, there are a number of advantages in turbines of such type like their independence from the change of wind direction, lower levels of aerodynamic and infrasound noises, higher structural reliability (compared to horizontal engines), etc. With these advantages, vertical-axis wind turbines demonstrate promising capacities. Inter alia, the productiveness of such turbines can be refined through the aerodynamic improvement of the structure and comprehensive optimization of the rotor geometry. The main purpose of the presented paper is to aerodynamically improve vertical wind turbine in order to increase the efficiency of wind energy conversion into electricity. Within the framework of the classical theory of impulses, this article presents a study of the effect of variation in Reynolds number on the general energy characteristics of a vertical-axis wind turbine with two blades. The integral approach makes it possible to use a single-disk impulse model to determine the main specific indicators of the system. The power factor was calculated based on the obtained value of the shaft torque factor, which in turn was determined by numerically integrating the total torque generated by the wind turbine. To calculate the test problem, we used the classic NACA airfoils: 0012, 0015, 0018 and 0021. The proposed calculation algorithm makes it possible not to indicate the Reynolds number and corresponding aerodynamic coefficients at the beginning of the calculation, but to recalculate it depending on the relative speed, position of the airfoil and the linear speed of the airfoil around the circumference. Proposed modern design techniques can be helpful for optimization of vertical wind turbines.

Computational fluid dynamic analysis of roof-mounted vertical-axis wind turbine with diffuser shroud, flange, and vanes

2018 ◽  
Vol 42 (4) ◽  
pp. 404-415
Author(s):  
H. Abu-Thuraia ◽  
C. Aygun ◽  
M. Paraschivoiu ◽  
M.A. Allard
Keyword(s):  
Wind Turbine ◽  
Urban Areas ◽  
Guide Vane ◽  
Fluid Dynamic ◽  
Vertical Axis ◽  
Power Coefficient ◽  
Small Scale ◽  
Vertical Axis Wind Turbine ◽  
Guide Vanes ◽  
Turbine Design

Advances in wind power and tidal power have matured considerably to offer clean and sustainable energy alternatives. Nevertheless, distributed small-scale energy production from wind in urban areas has been disappointing because of very low efficiencies of the turbines. A novel wind turbine design — a seven-bladed Savonius vertical-axis wind turbine (VAWT) that is horizontally oriented inside a diffuser shroud and mounted on top of a building — has been shown to overcome the drawback of low efficiency. The objective this study was to analyze the performance of this novel wind turbine design for different wind directions and for different guide vanes placed at the entrance of the diffuser shroud. The flow field over the turbine and guide vanes was analyzed using computational fluid dynamics (CFD) on a 3D grid for multiple tip-speed ratios (TSRs). Four wind directions and three guide-vane angles were analyzed. The wind-direction analysis indicates that the power coefficient decreases to about half when the wind is oriented at 45° to the main axis of the turbine. The analysis of the guide vanes indicates a maximum power coefficient of 0.33 at a vane angle of 55°.

Investigation of vertical axis wind turbine airfoil performance in rain

2017 ◽  
Vol 232 (2) ◽  
pp. 181-194 ◽  
Author(s):  
Zhenlong Wu ◽  
Yihua Cao
Keyword(s):  
Wind Turbine ◽  
Wind Turbines ◽  
Meteorological Condition ◽  
Vertical Axis ◽  
Vertical Axis Wind Turbine ◽  
Vertical Axis Wind Turbines ◽  
Turbine Performance ◽  
Practical Design ◽  
Wind Turbine Airfoil ◽  
Naca 0015

Rainfall is a common meteorological condition that wind turbines may encounter and by which their performance may be affected. This paper comprehensively investigates the effects of rainfall on a NACA 0015 airfoil which is commonly used in vertical axis wind turbines. A CFD-based Eulerian–Lagrangian multiphase approach is proposed to study the static, rotating, and oscillating performances of the NACA 0015 airfoil in rainy conditions. It is found that for the different airfoil movements, the airfoil performance can seriously be deteriorated in the rain condition. Rain also causes premature boundary layer separations and more severe flow recirculations than in the dry condition. These findings seem to be the first open reports on rain effects on wind turbine performance and should be of some significance to practical design.

scholarly journals On mooring line tension and fatigue prediction for offshore vertical axis wind turbines: A comparison of lumped mass and quasi-static approaches

2018 ◽  
Vol 42 (2) ◽  
pp. 97-107 ◽  
Author(s):  
D Cevasco ◽  
M Collu ◽  
CM Rizzo ◽  
M Hall
Keyword(s):  
Wind Turbine ◽  
Wind Turbines ◽  
Line Tension ◽  
Vertical Axis ◽  
Offshore Wind ◽  
Mooring Line ◽  
Offshore Wind Turbine ◽  
Vertical Axis Wind Turbine ◽  
Lumped Mass ◽  
Vertical Axis Wind Turbines

Despite several potential advantages, relatively few studies and design support tools have been developed for floating vertical axis wind turbines. Due to the substantial aerodynamics differences, the analyses of vertical axis wind turbine on floating structures cannot be easily extended from what have been already done for horizontal axis wind turbines. Therefore, the main aim of the present work is to compare the dynamic response of the floating offshore wind turbine system adopting two different mooring dynamics approaches. Two versions of the in-house aero-hydro-mooring coupled model of dynamics for floating vertical axis wind turbine (FloVAWT) have been used, employing a mooring quasi-static model, which solves the equations using an energetic approach, and a modified version of floating vertical axis wind turbine, which instead couples with the lumped mass mooring line model MoorDyn. The results, in terms of mooring line tension, fatigue and response in frequency have been obtained and analysed, based on a 5 MW Darrieus type rotor supported by the OC4-DeepCwind semisubmersible.

Sign in / Sign up

Export Citation Format

Share Document