Experimental Investigation of Using Solar Chimney to Induce Natural Ventilation

2014 ◽  
Vol 672-674 ◽  
pp. 109-112 ◽  
Author(s):  
Cai Xia Hao ◽  
Hai Ping Zhang ◽  
Min Xia Hao
Keyword(s):  
Heat Flux ◽  
Experimental Investigation ◽  
Velocity Field ◽  
Boundary Layers ◽  
Natural Ventilation ◽  
Heated Surface ◽  
Experimental Results ◽  
Solar Chimney ◽  
Air Velocity ◽  
Radiant Intensity

The vertical panels of solar chimney have internal dimensions of 2000mm height、1000mm length. Under the condition of heat flux and chimney gap variety, we research chimney interior velocity field. Experimental Results show that airflow increased with chimney gap augmentation, the airflow and air velocity augment with the increase of solar radiant intensity, and air velocity decreases with the increase of solar chimney gap. Air velocity is higher near the heated surfaces than it in the middle chimney. Meanwhile velocity boundary layers form near the heated surface.

CFD investigation of temperature distribution, air flow pattern and thermal comfort in natural ventilation of building using solar chimney

2020 ◽  
Vol 17 (1) ◽  
pp. 78-86 ◽  
Author(s):  
Maher Dhahri ◽  
Hana Aouinet
Keyword(s):  
Heat Flux ◽  
Temperature Distribution ◽  
Thermal Comfort ◽  
Natural Ventilation ◽  
Air Flow ◽  
Solar Chimney ◽  
Air Velocity ◽  
Content Type ◽  
Solar Heat ◽  
Solar Heat Flux

Purpose The purpose of this study is to investigate air flow, temperature distribution and thermal confort in natural ventilation induced by solar chimney for different operating. Design/methodology/approach Numerical simulation is performed using a commercial computational fluid dynamics (CFD) package ANSYS CFX software to understand the effects of air temperature, air velocity and solar heat flux on the performance of the solar chimney and thermal comfort. The comfort level was evaluated using the air diffusion performance index (ADPI) according to ASHRAE (55-210). The flow was investigated at inclination angles 45° solar heat flux 550-750 W/m2 and in a solar chimney of 1.4 m length, 0.6 m width and 0.20 m air gab. Findings The numerical results from the present simulation were first validated with experimental data, which was used for the thermal comfort indexes calculation. The obtained results of the analysis showed that the used numerical technique could accurately predict air flow and temperature distribution in natural ventilated building using solar chimney; the air temperature, air velocity and solar heat flux have a significant impact on thermal comfort; the temperature of 19°C with velocity of 0.15 m.s−1 gives the best effective draft temperature (EDT) satisfy ASHRAE (55-210) criteria that V = 0.35 m.s−1 and EDT range between −1.7 and 1.1. Originality/value In the present paper, air flow, temperature distribution and thermal comfort inside a room equipped with inclined solar chimney were numerically investigated and analyzed. The commercial CFD package (CFX 15) is used. Calculations are carried out in an empty room without any human or mechanical activity and the numerical results are compared with measurement points.

Experimental Study of a Vertical Channel Solar Chimney with Uniform Heat Flux for Natural Ventilation in Buildings

2011 ◽  
Vol 374-377 ◽  
pp. 585-589
Author(s):  
Hai Wei Jing ◽  
An Gui Li
Keyword(s):  
Experimental Study ◽  
Heat Flux ◽  
Velocity Field ◽  
Natural Ventilation ◽  
Vertical Channel ◽  
Heated Wall ◽  
Uniform Heat Flux ◽  
Airflow Rate ◽  
Optimum Ratio ◽  
Solar Chimney

A experimentally study has been carried out to predict airflow rate, temperature field and velocity field for different chimney gap and heat flux. Results showed that, for veritical solar chimney,there is an optimum ratio of chimney width-to height to achieve a maximum airflow rate. The optimum ratio is about 1：2. Meanwhile,temperature and velocity field of solar chimney channel were analyzed. The air temperature and the velocity approaching to the surface of the heated wall are higher than that away from the surface of the heated wall.

Natural-Ventilation Flow in a 3-D Room Fitted With Solar Chimney

2012 ◽  
Author(s):  
B. P. Huynh
Keyword(s):  
Heat Flux ◽  
Flow Pattern ◽  
Natural Ventilation ◽  
Air Flow ◽  
Ventilation Rate ◽  
High Heat Flux ◽  
Solar Chimney ◽  
Solar Heat ◽  
Solar Heat Flux ◽  
Inlet Opening

Natural-ventilation flow induced in a real-sized rectangular-box room fitted with a solar chimney on its roof is investigated numerically, using a commercial CFD (Computational Fluid Dynamics) software package. The chimney in turn is in the form of a parallel channel with one plate being subjected to uniform solar heat flux. Ventilation rate and air-flow pattern through the room are considered in terms of the heat flux for two different locations of the room’s inlet opening. Chien’s turbulence model of low-Reynolds-number K-ε is used in a Reynolds-Averaged Navier-Stokes (RANS) formulation. It is found that ventilation flow rate increases quickly with solar heat flux when this flux is low, but more gradually at higher flux. At low heat flux, ventilation rate is not significantly affected by location of the inlet opening to the room. On the other hand, at high heat flux, ventilation rate varies substantially with the opening’s location. Location of the inlet opening to the room also affects strongly the air-flow pattern. In any case, ample ventilation rate is readily induced by the chimney.

Experimental and Theoretical Investigation of Performance of a Solar Chimney Model, Part I: Experimental Investigation

2021 ◽  
Vol 3 (1) ◽  
Author(s):  
Essaied M Shuia ◽  
Bashir H Arebi ◽  
Ibrahim A abuashe
Keyword(s):  
Experimental Data ◽  
Wind Speed ◽  
Solar Radiation ◽  
Air Temperature ◽  
Solar Collector ◽  
Experimental Results ◽  
Internal Diameter ◽  
Solar Chimney ◽  
Air Velocity ◽  
Collector Temperature

This paper presents the experimental data that was collected from small pilot solar chimney. The experimental data together with ambient conditions are used to evaluate the performance and study the behavior of the solar chimney; this data will be used for comparison with theoretical models in another paper [part II). The solar chimney prototype was designed and constructed at the Subrata Faculty of Engineering-Libya. The data were collected over several days of June 2011. The solar chimney system contains two main components; the solar collector and the solar chimney. The solar collector root‘ has a circular area of126 m3, the solar chimney is a PVC tube with internal diameter of 0.2 m and the total height of chimney is 9.3 m. The measurements include the intensity of solar radiation inside/outside the collector, temperature and velocity of air at the entrance of the chimney, temperature and speed of wind outside the collector, temperature of the ground inside collector al1d temperature measurements of air at speci?c points at different levels throughout the collector. Solar irradiance was found to affect the chimney temperature and subsequently affects chimney air velocity. The experimental results showed that temperature differences of (30 - 45°C) were recorded between the ambient temperature and that of air inside the chimney in the middle of the day, where the highest air temperature of 73.4°C was recorded at the entrance of the solar chimney. The maximum air velocity of 3.6 m/s was recorded inside the solar chimney at noon on 9 June. Wind speed outside the collector had a small effect on the speed of the air inside the chimney and tends to change slightly, hence, can neglect influence of wind speed on the performance of the system. Also the experimental results indicate that such type of system can trap a suf?cient amount of solar radiation, which elevates the air temperature to a suf?cient value able to generate enough air ?ow to operate a wind turbine to produce electricity; this means the solar chimney system for electricity production can work in the north-western part of Libya in the summer time at least.

An experimental investigation of a solar chimney model with uniform wall heat flux

2003 ◽  
Vol 38 (7) ◽  
pp. 893-906 ◽  
Author(s):  
Z.D. Chen ◽  
P. Bandopadhayay ◽  
J. Halldorsson ◽  
C. Byrjalsen ◽  
P. Heiselberg ◽  
...  
Keyword(s):  
Heat Flux ◽  
Experimental Investigation ◽  
Wall Heat Flux ◽  
Solar Chimney ◽  
Uniform Wall ◽  
Uniform Wall Heat Flux

scholarly journals Experimental Investigation of Thermal Performance of a Solar Chimney Provided with a Porous Absorber Plate

2020 ◽  
Vol 26 (4) ◽  
pp. 1-20
Author(s):  
Bashaar Abdulkareem Hamood ◽  
Mohammed ABDUL RAOUF NIMA
Keyword(s):  
Experimental Investigation ◽  
Thermal Performance ◽  
Natural Ventilation ◽  
Metal Foam ◽  
Weather Condition ◽  
Ventilation Rate ◽  
Incline Angle ◽  
Solar Chimney ◽  
Absorber Plate ◽  
Air Temperatures

  Experimental investigation of the influence of inserting the metal foam to the solar chimney to induce natural ventilation are described and analyzed in this work. To carry out the experimental test, two identical solar chimneys (without insertion of metal foam and with insertion of metal foam) are designed and placed facing south with dimensions of length× width× air gap (2 m× 1 m× 0.2 m). Four incline angles are tested (20o,30o,45o,60o) for each chimney in Baghdad climate condition (33.3o latitude, 44.4o longitude) on October, November, December 2018. The solar chimney performance is investigated by experimentally recording absorber plate and air temperatures and velocity of air. Results indicated that the using metal foam absorber plate lead to reducing the mean temperature of absorber plate by 6.7 °C as a result, the values of chimney outlet air temperature increased. The daily solar chimney efficiency enhanced by 58.7% and the useful energy received also increased. The existence of metal foam caused higher air velocity at the exit and increasing in the ventilation rate that the maximum ventilate rate obtained from the solar chimney is 5.96 1/hr for 27 m3 volume of room at solar irradiance of 730 W/m2   for chimney incline angle of 60o. The results of the experimental work show that the addition of metal foam to the solar chimney as an absorber plate is an efficient method to enhance the characteristics of heat transfer and the thermal performance of the solar chimney in the weather condition of Iraq.

Solar Chimney Turbine: Part 2 of 2 — Experimental Results

Solar Energy ◽  
2002 ◽  
Author(s):  
Anthony J. Gannon ◽  
Theodore W. von Backstro¨m
Keyword(s):  
Experimental Investigation ◽  
Experimental Model ◽  
Experimental Results ◽  
Total Efficiency ◽  
Solar Chimney ◽  
Static Efficiency ◽  
Turbine Efficiency ◽  
Turbine Design ◽  
Current Turbine

An experimental investigation of a solar chimney turbine design is undertaken. The aim of the program is to demonstrate and evaluate a proposed solar chimney turbine design. The measured results of an experimental model turbine are presented and the turbine efficiency calculated. The current turbine design has a total-to-total efficiency of 85–90% and total-to-static efficiency of 77–80% over the design range. Secondary objectives are to compare the measured and predicted results and through investigation of the experimental results suggest improvements to the turbine design.

Experimental Study of Inclination on Non-Boiling Regime Spray Cooling

2008 ◽  
Author(s):  
Yongxian Guo ◽  
Jianyuan Jia ◽  
Weidong Wang ◽  
Shaorong Zhou
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Heated Surface ◽  
Spray Cooling ◽  
Copper Surface ◽  
Experimental Results ◽  
Working Fluid ◽  
Distilled Water ◽  
Optimal Heat ◽  
Inclination Angles

Based on the maximum CHF (critical heat flux) criterion, an optimal heat transfer criterion, which is called H criterion, was proposed. Experimental apparatuses were conducted. Distilled water was used as the working fluid. Three different DANFOSS nozzles with cone angles being 54°, 50° and 54° respectively were used. A 30×30mm2 square copper surface was used as the heated surface. Experimental results indicated that the volumetric fluxes were proportioned to P0.5, where P is the pressure drop across the nozzles. The optimal distance between the nozzles and the heated surface were derived. The results indicated that the optimal heat transfer appeared while the outside of the impellent thin spray film inscribed in the square heated surface. Based on the H criterion aforementioned, two DANFOSS nozzles of the three, with cone angles being 54° and 50° respectively, were used to study the temperature distribution of the heated surface while there were spray inclination angles during spray cooling experiments. Distilled water was also used impacting on the 30×30mm2 square copper surface aforementioned and a circular heated copper surface with diameters being 30mm respectively. The heat flux of the surface was kept in constant (about 26–35W/cm2). The inclination angles were 0°, 10°, 20°, 30°, 40° and 50° respectively. Three thermocouples imbedded in the heated surface were used to predict the grads of the temperature of the surface. Experimental results indicated that the temperature and the grads of the temperature of the surface increases first and then decreases with the increase of the inclination angle.

Sign in / Sign up

Export Citation Format

Share Document