scholarly journals Evaluation of the Effect of Fuel Properties on the Fuel Spray and Jet Characteristics in a HGV DI Diesel Engine Operated by Used Cooking Oils

2014 ◽  
Vol 694 ◽  
pp. 3-12 ◽  
Author(s):  
Buland Dizayi ◽  
Hu Li ◽  
Alison S. Tomlin ◽  
Adrian Cunliffe
Keyword(s):  
Diesel Engine ◽  
Fuel Injection ◽  
Rate Of Change ◽  
Injection System ◽  
Fuel Spray ◽  
Fuel Blend ◽  
Cooking Oil ◽  
Used Cooking Oil ◽  
Fuel Jet ◽  
Jet Characteristics

Fuel injection systems in modern diesel engines are designed and built to comply with very stringent environmental standards. They should also meet the highest level of fuel economy. Drivability, rapid response and easy and accurate control are a common demand. Changing the fuel characteristics could affect the performance of the fuel injection system. This study focuses on the evaluation of fuel spray characteristics of straight used cooking oil (SUCO) and its blends with petroleum diesel (PD) as a surrogate for pure PD. Used cooking oil blends have quite different physical properties from those of pure PD. Data for the lower heating value (LHV), density and viscosity were obtained from laboratory analysis. These data were merged with the physical and thermodynamic conditions of the diesel engine of interest to evaluate the dynamic behaviour of the fuel jet in 360° of crank rotation namely, the compression stroke, and the power stroke including the injection process. Engine operational conditions were calculated using a diesel dual thermodynamic cycle taking into account fuel injection adjustment at three different speeds, namely, idle speed, maximum torque speed and rated power speed. The results showed that fuel jet characteristics vary with SUCO content in the fuel blend. Two ranges of SUCO content in the blends were distinguished, 0 – 80% SUCO content and 80 – 100% SUCO content. Both showed a constant rate of change of jet characters per 10% increase in SUCO content in the fuel blend. Lower rates of change of fuel characters were observed at 0-80% SUCO content. The higher the temperature, the lower the rate of change of fuel jet characteristics.

scholarly journals Financial, energy, performance and emission analysis of a repurpose used cooking oil (RUCO) diesel fuel blends

2021 ◽  
Author(s):  
Tikendra Nath Verma ◽  
Abhishek Dasore ◽  
Pankaj Shrivastava ◽  
Ümit Ağbulut ◽  
Suat Sarıdemir ◽  
...  
Keyword(s):  
Diesel Engine ◽  
Diesel Fuel ◽  
Jatropha Curcas ◽  
Energy Performance ◽  
Pongamia Pinnata ◽  
Ecological Analysis ◽  
Emission Analysis ◽  
Performance And Emission ◽  
Cooking Oil ◽  
Used Cooking Oil

Abstract In this study, exergy, energy, performance and emission analysis were investigated for the repurpose used cooking oil (RUCO), Jatropha curcas (JC), Pongamia Pinnata (PP) and petroleum diesel fuel (PDF) fueled compression ignition engine under various engine loads. In this study, 20% of each biodiesel was tested in single cylinder, four stroke, diesel engine, given that open literature shows the potential use of biodiesel of up to 20% in a diesel engine without modification. The diesel engine was used to investigate their performance, combustion and emission characteristics of diesel-repurpose used cooking oil, Jatropha curcas, and Pongamia Pinnata fuel samples at different compression ratios and load condition. The results showed that thermal efficiency is higher with the PDF compared to DRUCO20, DJC20, DPP20 biodiesel blends. The exhaust gas temperature decreased and specific fuel consumption of the engine were increased by adding RUCO, Jatropha curcas, Pongamia Pinnata to petroleum diesel fuel. Engine ecological analysis showed that blended fuel reduces the average hydrocarbons (HC), carbon monoxide (CO) and NO X than petroleum diesel fuel. While DRUCO20 showed better performance and reduction in ecological analysis but higher ecological of CO 2 is comparable with DCJ20 and DPP20.

scholarly journals Experimental research of two stroke aircraft diesel engine

2019 ◽  
Vol 179 (4) ◽  
pp. 75-79
Author(s):  
Łukasz GRABOWSKI ◽  
Paweł KARPIŃSKI ◽  
Grzegorz BARAŃSKI
Keyword(s):  
Diesel Engine ◽  
Fuel Injection ◽  
Experimental Studies ◽  
Injection System ◽  
Temperature Control System ◽  
Maximum Pressure ◽  
System Control ◽  
Fuel Injection System ◽  
Measurement Systems ◽  
New Type

This paper presents the results of experimental studies of the opposed-piston diesel engine. This engine was designed during one of the stages of the research on a new-type drive unit for gyrocopter applications. In order to conduct research, a special test stand as well as control and measurement systems were developed. As part of the work on the engine, the fuel injection system, engine temperature control system and measurement systems were designed. In addition, a computer program has been developed for the fuel injection system control (injectors, valves fuel pressure regulators). The paper presents the results of the preliminary tests for a single value of engine speed (1500 rpm) and three values of load defined by torque. The measured value of the indicated pressure made it possible to calculate the maximum pressure. The results obtained from the bench tests were analyzed.

scholarly journals Influence of Fuel Injection Pressure on the Emissions Characteristics and Engine Performance in a CRDI Diesel Engine Fueled with Palm Biodiesel Blends

Energies ◽  
2019 ◽  
Vol 12 (20) ◽  
pp. 3837 ◽  
Author(s):  
Sam Ki Yoon ◽  
Jun Cong Ge ◽  
Nag Jung Choi
Keyword(s):  
Diesel Engine ◽  
Diesel Fuel ◽  
Fuel Injection ◽  
Injection Pressure ◽  
Biodiesel Fuel ◽  
Nox Emissions ◽  
Oxides Of Nitrogen ◽  
Fuel Blend ◽  
Engine Load ◽  
Fuel Injection Pressure

This experiment investigates the combustion and emissions characteristics of a common rail direct injection (CRDI) diesel engine using various blends of pure diesel fuel and palm biodiesel. Fuel injection pressures of 45 and 65 MPa were investigated under engine loads of 50 and 100 Nm. The fuels studied herein were pure diesel fuel 100 vol.% with 0 vol.% of palm biodiesel (PBD0), pure diesel fuel 80 vol.% blended with 20 vol.% of palm biodiesel (PBD20), and pure diesel fuel 50 vol.% blended with 50 vol.% of palm biodiesel (PBD50). As the fuel injection pressure increased from 45 to 65 MPa under all engine loads, the combustion pressure and heat release rate also increased. The indicated mean effective pressure (IMEP) increased with an increase of the fuel injection pressure. In addition, for 50 Nm of the engine load, an increase to the fuel injection pressure resulted in a reduction of the brake specific fuel consumption (BSFC) by an average of 2.43%. In comparison, for an engine load of 100 Nm, an increase in the fuel injection pressure decreased BSFC by an average of 0.8%. Hydrocarbon (HC) and particulate matter (PM) decreased as fuel pressure increased, independent of the engine load. Increasing fuel injection pressure for 50 Nm engine load using PBD0, PBD20 and PBD50 decreased carbon monoxide (CO) emissions. When the fuel injection pressure was increased from 45 MPa to 65 MPa, oxides of nitrogen (NOx) emissions were increased for both engine loads. For a given fuel injection pressure, NOx emissions increased slightly as the biodiesel content in the fuel blend increased.

Sign in / Sign up

Export Citation Format

Share Document