Analysis of Tool Performance during Ball-End Milling of Aluminium Alloy 6061-T6

2015 ◽  
Vol 761 ◽  
pp. 318-323 ◽  
Author(s):  
Mohd Shahir Kasim ◽  
Mohamad Hazizan Atan ◽  
C.H. Che Haron ◽  
Jaharah A. Ghani ◽  
Mohd Amri Sulaiman ◽  
...  
Keyword(s):  
Aluminium Alloy ◽  
Feed Rate ◽  
Failure Modes ◽  
End Milling ◽  
Cutting Speed ◽  
Depth Of Cut ◽  
Cutting Condition ◽  
Tool Performance ◽  
Coated Carbide ◽  
Alloy 6061

This article presents the tool wear mechanism when machining Aluminium alloy 6061-T6 with PVD coated carbide under dry cutting condition. Cutting parameters selected were cutting speed, Vc = 115-145 m/min; feed rate fz = 0.15-0.2 mm/tooth and depth of cut, ap = 0.5-0.75 mm. The result showed the tool life of PVD TiAlN ranged from 11 to 97 min. Full factorial approach was employed to exhibit relationship between parameter input and output. From the analysis, cutting speed was found to be the most significant factor for tool performance followed by feed rate and depth of cut. It was also found that most of failure modes occurred were notch wear and flaking near those found near depth of cut line.

Research on Relationship between Cutting Conditions and Chip Formation during End Milling of Aluminium Alloy 6061

2017 ◽  
Vol 909 ◽  
pp. 56-60
Author(s):  
Mohd Rasidi Ibrahim ◽  
Najah Mahadi ◽  
Afiff Latif ◽  
Zulafif Rahim ◽  
Zazuli Mohid ◽  
...  
Keyword(s):  
Aluminium Alloy ◽  
Feed Rate ◽  
End Milling ◽  
Cutting Speed ◽  
Chip Thickness ◽  
Chip Morphology ◽  
Depth Of Cut ◽  
Slot Milling ◽  
Milling Operation ◽  
Alloy 6061

This paper studied chip morphology in end milling of aluminium alloy 6061 by various cutting parameter such as feed rate, cutting speed and depth of cut. Slot milling operation were conducted. The analysis consists of chip morphology, chip weight, chip thickness and chip length. Scanning Electron Microscope (SEM) were used to obtain and examine the chips. Result shows that, end milling with higher cutting speed, feed rate and depth of cut generated short, small and light weigh of chips.

Tool Wear Analysis in End Milling of Advanced Ceramics with TiAlN and TiN Coated Carbide Inserts

2012 ◽  
Vol 576 ◽  
pp. 76-79
Author(s):  
M. Mohan Reddy ◽  
Alexander Gorin ◽  
Khaled A. Abou-El-Hossein ◽  
D. Sujan ◽  
Mohammad Yeakub Ali ◽  
...  
Keyword(s):  
Tool Wear ◽  
Feed Rate ◽  
End Milling ◽  
Cutting Speed ◽  
High Hardness ◽  
Depth Of Cut ◽  
Cutting Condition ◽  
Dry Cutting ◽  
Coated Carbide ◽  
Axial Depth

Advanced ceramic materials are difficult to machine by conventional methods due to the brittle nature and high hardness. The appropriate selection of cutting tool and cutting conditions may help to improve machinability by endmilling. Performance of TiAlN and TiN coated carbide tool insert in end milling of machinable glass ceramic has been investigated. Several dry cutting tests were performed to select the optimum cutting parameters for the endmilling in order to obtain better tool life. In this work, a study was carried out on the influence of cutting speed, feed rate and axial depth of cut on tool wear.The technique of design of experiments (DOE) was used for the planning and analysis of the experiments. Tool wear prediction model was developed using Response surface methodology.The results indicate that tool wear increased with increasing the cutting speed and axial depth of cut. Effect of feed rate is not much significant on selected range of cutting condition

scholarly journals Surface Quality and Chip Formation in Turning of LM6 Aluminium Alloy and Particulate Reinforced Metal Matrix Composite

2013 ◽  
Vol 773-774 ◽  
pp. 894-901
Author(s):  
Muhammad Yusuf ◽  
M.K.A. Ariffin ◽  
N. Ismail ◽  
S. Sulaiman
Keyword(s):  
Surface Roughness ◽  
Aluminium Alloy ◽  
Surface Quality ◽  
Chip Formation ◽  
Feed Rate ◽  
Metal Matrix ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Depth Of Cut ◽  
Cutting Condition

Majority of the components of aerospace and automotive vehicles need different machining operations, mainly for the assembly requirements. The components have to present both high dimensional precision and surface quality. This present work is concerned with the effect of cutting parameters (cutting speed, feed rate and depth of cut) on the surface roughness and the chip formation in turning process. The machining results are compared with LM6 aluminium alloy and TiC reinforced metal matrix composite under the same cutting conditions and tool geometry. The cutting condition models designed based on the Design of Experiments Response Surface Methodology. The objective of this research is to obtaining the optimum cutting parameters to get a better surface quality and also the chip formation and furthermore does not hazardous to the worker and the machined products quality. Results shows that Surface roughness values of LM6-TiC composite are higher as compared LM6 alloy at similar cutting condition. With increasing in cutting speed improves the surface quality. The surface quality increases with decrease of the feed rate and the depth of cut. There are difference chip forms for LM6 aluminium alloy and Al-TiC composite for a similar of cutting condition. Generally, chip formations of both materials are acceptable and favourable for the worker as well as the products and the tools.

The Study of Coated Carbide Ball End Milling Tools on Inconel 718 Using Numerical Simulation Analysis to Attain Cutting Force and Temperature Predictive Models at the Cutting Zone

2017 ◽  
Vol 882 ◽  
pp. 28-35 ◽  
Author(s):  
S.E.M. Chien ◽  
M.M. Reddy ◽  
V.C.C. Lee ◽  
D. Sujan
Keyword(s):  
Numerical Simulation ◽  
Finite Element ◽  
Cutting Force ◽  
Feed Rate ◽  
End Milling ◽  
Cutting Speed ◽  
Depth Of Cut ◽  
Ball End Milling ◽  
Cutting Zone ◽  
Coated Carbide

The unique properties of Inconel 718 make it a challenging material to machine especially in ball end milling operations due to high cutting force and temperature concentrated at the cutting zone. These essentially lead to accelerated tool wear and failure resulting in high costs and loss of production. In this research, finite element numerical simulation was performed using AdvantEdge to simulate ball end milling using an 8mm TiAlN coated carbide tool. Response Surface Methodology (RSM) is applied by using a 3 level 3 factorial Box-Behnken design of experiment with different combinations of cutting speed, feed rate, and depth of cut parameters with a selected range of parameters to simulate finishing operations. Temperature contour from finite element analysis showed that the highest temperature occurs near the depth of cut line just before the chip separates from the workpiece. Using multiple linear regression, a quadratic polynomial model is developed for maximum cutting force and a linear polynomial model peak tool temperature response respectively. Analysis of Variance (ANOVA) showed that feed rate had the most significance for cutting force followed by depth of cut. Also, cutting speed was found to have little influence. For peak tool temperature, cutting speed was the most significant cutting parameter followed by feed rate and depth of cut.

A Comprehensive Study on Surface Roughness in Machining of AISI D2 Hardened Steel

2012 ◽  
Vol 576 ◽  
pp. 60-63 ◽  
Author(s):  
N.A.H. Jasni ◽  
Mohd Amri Lajis
Keyword(s):  
Surface Roughness ◽  
High Speed ◽  
End Milling ◽  
Cutting Speed ◽  
Hardened Steel ◽  
Depth Of Cut ◽  
Feed Speed ◽  
Radial Depth ◽  
Aisi D2 ◽  
Coated Carbide

Hard milling of hardened steel has wide application in mould and die industries. However, milling induced surface finish has received little attention. An experimental investigation is conducted to comprehensively characterize the surface roughness of AISI D2 hardened steel (58-62 HRC) in end milling operation using TiAlN/AlCrN multilayer coated carbide. Surface roughness (Ra) was examined at different cutting speed (v) and radial depth of cut (dr) while the measurement was taken in feed speed, Vf and cutting speed, Vc directions. The experimental results show that the milled surface is anisotropic in nature. Surface roughness values in feed speed direction do not appear to correspond to any definite pattern in relation to cutting speed, while it increases with radial depth-of-cut within the range 0.13-0.24 µm. In cutting speed direction, surface roughness value decreases in the high speed range, while it increases in the high radial depth of cut. Radial depth of cut is the most influencing parameter in surface roughness followed by cutting speed.

Multi-criteria optimization and predictive modeling of turning forces in high-speed machining of yttria based zirconia toughened alumina insert using desirability function approach

2015 ◽  
Vol 231 (8) ◽  
pp. 1396-1408 ◽  
Author(s):  
Nilrudra Mandal ◽  
B Doloi ◽  
Biswanath Mondal ◽  
BK Singh
Keyword(s):  
Feed Rate ◽  
High Speed ◽  
Desirability Function ◽  
Cutting Speed ◽  
Depth Of Cut ◽  
Cutting Condition ◽  
Machining Forces ◽  
Feed Force ◽  
Response Optimization ◽  
Zirconia Toughened Alumina

An attempt has been made to apply the Taguchi parameter design method and multi-response optimization using desirability analysis for optimizing the cutting conditions (cutting speed, feed rate and depth of cut) on machining forces while finish turning of AISI 4340 steel using developed yttria based zirconia toughened alumina inserts. These zirconia toughened alumina inserts were prepared through wet chemical co-precipitation route followed by powder metallurgy process. The L9 (4) orthogonal array of the Taguchi experiment is selected for three major parameters, and based on the mean response and signal-to-noise ratio of measured machining forces, the optimal cutting condition arrived for feed force is A1, B1 and C3 (cutting speed: 150 m/min, depth of cut: 0.5 mm and feed rate: 0.28 mm/rev) and for thrust and cutting forces is A3, B1 and C1 (cutting speed: 350 m/min, depth of cut: 0.5 mm and feed rate: 0.18 mm/rev) considering the smaller-the-better approach. Multi-response optimization using desirability function has been applied to minimize each response, that is, machining forces, simultaneously by setting a goal of highest cutting speed and feed rate criteria. From this study, it can be concluded that the optimum parameters can be set at cutting speed of 350 m/min, depth of cut of 0.5 mm and feed rate of 0.25 mm/rev for minimizing the forces with 78% desirability level.

Cutting Forces and Surface Roughness in High-Speed End Milling of Ti6Al4V

2013 ◽  
Vol 589-590 ◽  
pp. 76-81
Author(s):  
Fu Zeng Wang ◽  
Jun Zhao ◽  
An Hai Li ◽  
Jia Bang Zhao
Keyword(s):  
Surface Roughness ◽  
Surface Quality ◽  
Cutting Forces ◽  
High Speed ◽  
End Milling ◽  
Cutting Speed ◽  
Depth Of Cut ◽  
Wide Range ◽  
Radial Depth ◽  
Coated Carbide

In this paper, high speed milling experiments on Ti6Al4V were conducted with coated carbide inserts under a wide range of cutting conditions. The effects of cutting speed, feed rate and radial depth of cut on the cutting forces, chip morphologies as well as surface roughness were investigated. The results indicated that the cutting speed 200m/min could be considered as a critical value at which both relatively low cutting forces and good surface quality can be obtained at the same time. When the cutting speed exceeds 200m/min, the cutting forces increase rapidly and the surface quality degrades. There exist obvious correlations between cutting forces and surface roughness.

Optimization of Process Parameters in the Turning Operation of Inconel 625

2019 ◽  
Vol 969 ◽  
pp. 756-761
Author(s):  
Hari Vasudevan ◽  
Ramesh Rajguru ◽  
Moeiz Shaikh ◽  
Arsalan Shaikh
Keyword(s):  
Feed Rate ◽  
Cutting Speed ◽  
Influential Factor ◽  
Inconel 625 ◽  
Depth Of Cut ◽  
Turning Operation ◽  
Wide Range ◽  
Coated Carbide ◽  
Taguchi’S Design Of Experiments ◽  
Super Alloy

Many difficult to machine materials, such as Inconel 625Ni-based super alloy, are uncommon class of metallic materials with exceptional combination of greater thermal strength, toughness and resistance to deterioration. They have extensive applications in the manufacturing of new aero-engines, besides its enormous uses in marine, chemical and oil & petrochemical industries. In the context of its wide range of applications, there is a need for efficiently processing better methods in the manufacturing of such difficult to machine materials. This study consists of the turning operation of Ni-based super alloy Inconel 625 without coolant, carried out by physical vapour deposition (PVD) coated carbide inserts. The response parameters, such as surface roughness and material removal rate were evaluated in terms of cutting speed, feed rate and depth of cut. Sixteen experiments were carried out, based on Taguchi's Design of Experiments using orthogonal array. The resulting analysis was done based on response graph. The experimental results revealed that the feed rate was the most influential factor, followed by the depth of cut and cutting speed. The optimal parameters achieved were cutting speed of 90 m/min, the feed rate of 0.35 mm/rev and the depth of cut 0.2 mm.

Modeling & Optimization of Surface Roughness & Vibration Amplitude in Heat Assisted End Milling of SKD 11 Tool Steel Using Ball Nose Tool

2012 ◽  
Vol 538-541 ◽  
pp. 799-803 ◽  
Author(s):  
A.K.M. Nurul Amin ◽  
Muhd Hafiz B. Md. Saad ◽  
Muammer Din Arif
Keyword(s):  
Surface Roughness ◽  
Response Surface ◽  
Tool Steel ◽  
Vibration Amplitude ◽  
End Milling ◽  
Heating Temperature ◽  
Cutting Speed ◽  
Depth Of Cut ◽  
Primary Input ◽  
Coated Carbide

Tool steel - SKD 11 is frequently used in industries for making dies and molds. This grade is chosen for its toughness, strength, and hardness maintained up to high temperature. However, the same properties make the steel extremely difficult and expensive to machine using conventional approaches. Heat assisted machining has been found wide spread application in recent years to improve machinability of difficult-to-cut materials. This research paper presents the outcome of an investigation on heat assisted end milling of SKD 11 conducted on a vertical machining center using ball nose coated carbide inserts. The Design of Experiments (DoE) was done using the Response Surface Methodology, in order to develop empirical mathematical models of surface roughness and vibration in terms of cutting speed, feed, axial depth of cut, and heating temperature. The models were checked for significance using Analysis of Variance (ANOVA). 3-D response surface graphs of the interactions of primary cutting parameters with the responses were plotted. Optimization was then performed by using the desirability function approach. From the graphs and optimized results it was concluded that the primary input parameters could be controlled in order to reduce vibration amplitude and produce semi-finished machined surfaces applying induction heat assisted technique.

Experimental Study of End Milling Force on Manganese Steel

2013 ◽  
Vol 718-720 ◽  
pp. 239-243
Author(s):  
Girma Seife Abebe ◽  
Ping Liu
Keyword(s):  
Cutting Force ◽  
Feed Rate ◽  
End Milling ◽  
Cutting Speed ◽  
Second Order ◽  
Manganese Steel ◽  
Depth Of Cut ◽  
Machining Deformation ◽  
Radial Depth ◽  
Axial Depth

Cutting force is a key factor influencing the machining deformation of weak rigidity work pieces. In order to reduce the machining deformation and improve the process precision and the surface quality, it is necessary to study the factors influencing the cutting force and build the regression model of cutting forces. This paper discusses the development of the first and second order models for predicting the cutting force produced in end-milling operation of modified manganese steel. The first and second order cutting force equations are developed using the response surface methodology (RSM) to study the effect of four input cutting parameters (cutting speed, feed rate, radial depth and axial depth of cut) on cutting force. The separate effect of individual input factors and the interaction between these factors are also investigated in this study. The received second order equation shows, based on the variance analysis, that the most influential input parameter was the feed rate followed by axial depth, and radial depth of cut. It was found that the interaction of feed with axial depth was extremely strong. In addition, the interactions of feed with radial depth; and feed rate with radial depth of cut were observed to be quite significant. The predictive models in this study are believed to produce values of the longitudinal component of the cutting force close to those readings recorded experimentally with a 95% confident interval.

Sign in / Sign up

Export Citation Format

Share Document