Research and Analysis on the Wave Transformation and Irregular Wave Breaking Criterion on the Shore

2016 ◽  
Vol 858 ◽  
pp. 354-358
Author(s):  
Tao You ◽  
Li Ping Zhao ◽  
Zheng Xiao ◽  
Lun Chao Huang ◽  
Xiao Rui Han
Keyword(s):  
Theoretical Model ◽  
Wave Height ◽  
Wave Breaking ◽  
Surf Zone ◽  
Breaking Waves ◽  
Wave Transformation ◽  
Breaking Wave ◽  
Height Distribution ◽  
Flume Experiments ◽  
Irregular Wave

Within the surf zone which is the region extending from the seaward boundary of wave breaking to the limit of wave uprush, breaking waves are the dominant hydrodynamics acting as the key role for sediment transport and beach profile change. Breaking waves exhibit various patterns, principally depending on the incident wave steepness and the beach slope. Based on the equations of conservation of mass, momentum and energy, a theoretical model for wave transformation in and outside the surf zone was obtained, which is used to calculate the wave shoaling, wave set-up and set down and wave height distributions in and outside the surf zone. The analysis and comparison were made about the breaking point location and the wave height variation caused by the wave breaking and the bottom friction, and about the wave breaking criterion under regular and irregular breaking waves. Flume experiments relating to the regular and irregular breaking wave height distribution across the surf zone were conducted to verify the theoretical model. The agreement is good between the theoretical and experimental results.

scholarly journals WAVE HEIGHT DISTRIBUTION AND WAVE GROUPING IN SURF ZONE

1982 ◽  
Vol 1 (18) ◽  
pp. 4 ◽  
Author(s):  
Hajime Mase ◽  
Yuichi Iwagaki
Keyword(s):  
Wave Height ◽  
Surf Zone ◽  
Irregular Waves ◽  
Wave Transformation ◽  
Height Distribution ◽  
Frequency Distributions ◽  
Irregular Wave ◽  
Wave Height Distribution ◽  
Wave Heights ◽  
Deep Water Wave

The main purpose of this paper is to propose a model for prediction of the spatial distributions of representative wave heights and the frequency distributions of wave heights of irregular waves in shallow-water including the surf zone. In order to examine the validity of the model, some experiments of irregular wave transformation have been made. In addition, an attempt has been made to clarify the spatial distribution of wave grouping experimentally. Especially the present paper focuses finding the effects of the bottom slope and the deep-water wave steepness on the wave height distribution and wave grouping.

scholarly journals COMPUTATIONS OF LONGSHORE CURRENTS

1964 ◽  
Vol 1 (9) ◽  
pp. 12
Author(s):  
Tsao-Yi Chiu ◽  
Per Bruun
Keyword(s):  
Wave Height ◽  
Wave Breaking ◽  
Surf Zone ◽  
Wave Spectrum ◽  
Wave Theory ◽  
Breaking Wave ◽  
Height Distribution ◽  
Longshore Current ◽  
Longshore Currents ◽  
Actual Height

This article introduces the longshore current computations based on theories published under the title "Longshore Currents and Longshore Troughs" (Bruun, 1963). Two approaches are used to formulate the longshore current velocities for a beach profile with one bar under the following assumptions: (1) that longshore current is evenly distributed (or a mean can be taken) along the depthj (2) that the solitary wave theory is applicable for waves in the surf zone; (3) that the statistical wave-height distribution for a deep water wave spectrum with a single narrow band of frequencies can be used near the shore, and (4) that the depth over the bar crest, Dcr, equal 0.8Hv/i /o\. Breaking wave height H^Q/^X is designated to be the actual height equal to Hw-j (significant wave height). Diagrams have been constructed for both approaches for beach profiles with one bar, from which longshore current velocities caused by various wave-breaking conditions can be read directly. As for longshore currents along the beach with a multibar system, fifteen diagrams covering a great variety of wave-breaking conditions are provided for obtaining longshore current velocities in different troughs.

scholarly journals Studi Hindcasting Dalam Menentukan Karakteristik Gelombang dan Klasifikasi Zona Surf Di Pantai Uluwatu, Bali

2018 ◽  
Vol 5 (1) ◽  
pp. 119
Author(s):  
Karina Santoso ◽  
I Dewa Nyoman Nurweda Putra ◽  
I Gusti Bagus Sila Dharma
Keyword(s):  
Wave Height ◽  
Calculation Result ◽  
Significant Wave Height ◽  
Surf Zone ◽  
Wind Data ◽  
Wave Transformation ◽  
Breaking Wave ◽  
Significant Wave ◽  
The World

Bali is one of the islands where there are many surf zones with various characteristics. In addition, Bali is also a heaven with a classy wave for the surfers of the world. One of the most challenging places to surf in Bali is Uluwatu Beach. Uluwatu Beach is ranked the 3rd best surf spot in the world version of CNN Travel in 2012. Wind causes sea waves, therefore wind data can be used to estimate the height and direction of the waves. Wave Hindcasting with Sverdrup, Munk and Bretschneider (SMB) method is calculated based on wind data for 10 years (2001 - 2010) from BMKG Ngurah Rai Station - Denpasar to obtain a significant wave height and period. In this research, it is necessary to approach through Hindcasting procedure, wave transformation analysis and surfing Terminology in determining the type of breaking wave and classification of surf zone in Uluwatu Beach area. Wave calculation result in Uluwatu Beach dominated by wave that coming from west side with significant wave height (Hs) of 0.98 m and significant wave period (Ts) of 5.21 s. The wave height due to the influence of wave refraction and shoaling is 0.976 m. The breaking wave height obtained from the calculation is 1.04 m at a depth of 0.849 m. From the result in this research, it can be concluded that the breaking wave type that occurred at Uluwatu Beach is plunging type according to the calculation result from its Irribaren number (0.4 <Ni <2.3). The classification of the surf zone at Uluwatu Beach based on its breakup type of wave is thought to be a good zone for surfers on intermediate level.

scholarly journals ENERGY LOSS AND SET-UP DUE TO BREAKING OF RANDOM WAVES

1978 ◽  
Vol 1 (16) ◽  
pp. 32 ◽  
Author(s):  
J.A. Battjes ◽  
J.P.F.M. Janssen
Keyword(s):  
Wave Height ◽  
Dissipation Rate ◽  
Breaking Waves ◽  
Breaking Wave ◽  
Height Distribution ◽  
Random Waves ◽  
Dissipation Of Energy ◽  
Wave Height Distribution ◽  
Set Up ◽  
Local Depth

A description is given of a model developed for the prediction of the dissipation of energy in random waves breaking on a beach. The dissipation rate per breaking wave is estimated from that in a bore of corresponding height, while the probability of occurrence of breaking waves is estimated on the basis of a wave height distribution with an upper cut-off which in shallow water is determined mainly by the local depth. A comparison with measurements of wave height decay and set-up, on a plane beach and on a beach with a bar-trough profile, indicates that the model is capable of predicting qualitatively and quantitatively all the main features of the data.

scholarly journals IRREGULAR WAVE TRANSFORMATION AFFECTED BY OPPOSING CURRENTS

1986 ◽  
Vol 1 (20) ◽  
pp. 53
Author(s):  
Shigeki Sakai ◽  
Kouestu Hiyamizu ◽  
Hiroshi Saeki
Keyword(s):  
Wave Height ◽  
Present Model ◽  
Surf Zone ◽  
Transformation Model ◽  
Irregular Waves ◽  
Wave Transformation ◽  
Irregular Wave ◽  
Sea Bed ◽  
Dimensionless Unit ◽  
Deep Water Wave

Transformation of irregular waves affected by opposing currents on a sloping sea bed was discussed, experimentally and theoretically. It was found that representative values of wave height, such as a significant wave height, are larger before breaking and the wave height decaying occurs more promptly in a surf zone as opposing currents become dominant, and that characteristics of a irregular wave transformation are determined by the dimensionless unit width discharge q* and the deep water wave steepness. This means that the effects of opposing currents on irregular wave transformation are qualitatively identical to that on the regular waves. A transformation model of irregular waves affected by opposing currents was presented. In the model, formulations for a regular wave transformation, in which the effects of opposing currents were taken into account, were applied to individual waves defined by zero-down" cross-method from irregular wave profiles. Comparisons between experimental results and the prediction by the model showed that the present model gives a good explanation for wave height distributions and the experimental finding that the surf zone is moved offshore by opposing currents.

scholarly journals Numerical Simulations of Non-Breaking, Breaking and Broken Wave Interaction with Emerged Vegetation Using Navier-Stokes Equations

Water ◽  
2019 ◽  
Vol 11 (12) ◽  
pp. 2561 ◽  
Author(s):  
Xuefeng Zou ◽  
Liangsheng Zhu ◽  
Jun Zhao
Keyword(s):  
Wave Propagation ◽  
Wave Height ◽  
Wave Breaking ◽  
Surf Zone ◽  
Stokes Equations ◽  
Wave Interaction ◽  
Breaking Waves ◽  
Breaking Point ◽  
Navier Stokes ◽  
Inertia Force

Coastal plants can significantly dissipate water wave energy and services as a part of shoreline protection. Using plants as a natural buffer from wave impacts remains an attractive possibility. In this paper, we present a numerical investigation on the effects of the emerged vegetation on non-breaking, breaking and broken wave propagation through vegetation over flat and sloping beds using the Reynolds-average Navier-Stokes (RANS) equations coupled with a volume of fluid (VOF) surface capturing method. The multiphase two-equation k-ω SST turbulence model is adopted to simulate wave breaking and takes into account the effects enhanced by vegetation. The numerical model is validated with existing data from several laboratory experiments. The sensitivities of wave height evolution due to wave conditions and vegetation characteristics with variable bathymetry have been investigated. The results show good agreement with measured data. For non-breaking waves, the wave reflection due to the vegetation can increase wave height in front of the vegetation. For breaking waves, it is shown that the wave breaking behavior can be different when the vegetation is in the surf zone. The wave breaking point is slightly earlier and the wave height at the breaking point is smaller with the vegetation. For broken waves, the vegetation has little effect on the wave height before the breaking point. Meanwhile, the inertia force is important within denser vegetation and is intended to decrease the wave damping of the vegetation. Overall, the present model has good performance in simulating non-breaking, breaking and broken wave interaction with the emerged vegetation and can achieve a better understanding of wave propagation over the emerged vegetation.

scholarly journals SURF ZONE WAVE HEATING BY ENERGY DISSIPATION OF BREAKING WAVES

2018 ◽  
pp. 2 ◽  
Author(s):  
Zhangping Wei ◽  
Robert A. Dalrymple
Keyword(s):  
Internal Energy ◽  
Wave Energy ◽  
Water Waves ◽  
Wave Breaking ◽  
Surf Zone ◽  
Current System ◽  
Breaking Waves ◽  
Breaking Wave ◽  
Conservation Of Energy ◽  
Wave Heating

This study investigates surf zone wave heating due to the dissipation of breaking wave energy by using the Smoothed Particle Hydrodynamics method. We evaluate the surf zone wave heating by examining the increase of internal energy of the system, which is computed based on the conservation of energy. The equivalent temperature profile is calculated based on a simple conversion relationship between energy and temperature. We first examine the surf zone wave heating based on long-crested wave breaking over a planar beach, and we consider spilling breaker and weakly plunging breaker. Numerical results show that breaking of water waves in the surf zone increases the internal energy of water body. Furthermore, the dissipation of incident wave energy is fully converted into the internal energy in a thermally isolated system, confirming the energy conservation of the present numerical approach. It is further found that the long-crested wave breaking generates undertow, which transports the generated wave heating from the surf zone to deep waters. We further carry out numerical experiments to examine surf zone wave heating due to short-crested wave breaking over a beach. The internal energy generation mainly follows the isolated wave breakers, and there is a 3D pattern of wave heating due to the complicated wave breaking process and current system. In general, the magnitude of the generated internal energy or temperature by dissipation of breaking wave energy in the surf zone is relatively small. The present study shows that the generated water temperature is in the order of 10^-3 Kelvin for wave breaking over a typical coastal beach.

scholarly journals Breaking-Wave Induced Transient Pore Pressure in a Sandy Seabed: Flume Modeling and Observations

2021 ◽  
Vol 9 (2) ◽  
pp. 160
Author(s):  
Changfei Li ◽  
Fuping Gao ◽  
Lijing Yang
Keyword(s):  
Pore Pressure ◽  
Wave Height ◽  
Wave Breaking ◽  
Breaking Waves ◽  
Breaking Wave ◽  
Regular Waves ◽  
Large Wave ◽  
Pore Pressures ◽  
Linear Waves ◽  
Wave Induced

Previous studies on wave-induced pore pressure in a porous seabed mainly focused on non-breaking regular waves, e.g., Airy linear waves or Stokes non-linear waves. In this study, breaking-wave induced pore pressure response in a sandy seabed was physically simulated with a large wave flume. The breaking-wave was generated by superimposing a series of longer waves onto the foregoing shorter waves at a specified location. Water surface elevations and the corresponding pore pressure in the process of wave breaking were measured simultaneously at three typical locations, i.e., at the rear, just at, and in front of the wave breaking location. Based on test results, characterization parameters are proposed for the wave surface elevations and the corresponding pore-pressures. Flume observations indicate that the wave height was greatly diminished during wave breaking, which further affected the pore-pressure responses. Moreover, the measured values of the characteristic time parameters for the breaking-wave induced pore-pressure are larger than those for the free surface elevation of breaking-waves. Under the action of incipient-breaking or broken waves, the measured values of the amplitude of transient pore-pressures are generally smaller than the predicted results with the analytical solution by Yamamoto et al. (1978) for non-breaking regular waves with equivalent values of characteristic wave height and wave period.

scholarly journals WAVE SPECTRUM OF BREAKING WAVE

1976 ◽  
Vol 1 (15) ◽  
pp. 32 ◽  
Author(s):  
Toru Sawaragi ◽  
Koichiro Iwata
Keyword(s):  
Experimental Data ◽  
Wave Height ◽  
Power Law ◽  
Wave Breaking ◽  
Surf Zone ◽  
Wave Spectrum ◽  
Breaking Wave ◽  
Harmonic Frequency ◽  
Dimensional Consideration

By wave breaking, an incident monocromatic wave is transformed to a wave composed of its harmonic frequency waves inside a surf zone. Based on a dimensional consideration, the "-1 power law ", the "-2 power law ", the "-2/3 power law " and the "-1/2 power law " on the wave height spectrum ,H(f), are derived as sorts of equilibrium spectra. These spectra except"-l/2 power law" are shown to agree with experimental data.

Bulk drag coefficient of a subaquatic vegetation subjected to irregular waves: Influence of Reynolds and Keulegan-Carpenter numbers

2020 ◽  
pp. 34-42
Author(s):  
Thibault Chastel ◽  
Kevin Botten ◽  
Nathalie Durand ◽  
Nicole Goutal
Keyword(s):  
Drag Coefficient ◽  
Wave Height ◽  
Wave Attenuation ◽  
Empirical Relationship ◽  
Breaking Waves ◽  
Irregular Waves ◽  
Geometrical Parameters ◽  
Flume Experiments ◽  
Seagrass Meadows ◽  
Artificial Vegetation

Seagrass meadows are essential for protection of coastal erosion by damping wave and stabilizing the seabed. Seagrass are considered as a source of water resistance which modifies strongly the wave dynamics. As a part of EDF R & D seagrass restoration project in the Berre lagoon, we quantify the wave attenuation due to artificial vegetation distributed in a flume. Experiments have been conducted at Saint-Venant Hydraulics Laboratory wave flume (Chatou, France). We measure the wave damping with 13 resistive waves gauges along a distance L = 22.5 m for the “low” density and L = 12.15 m for the “high” density of vegetation mimics. A JONSWAP spectrum is used for the generation of irregular waves with significant wave height Hs ranging from 0.10 to 0.23 m and peak period Tp ranging from 1 to 3 s. Artificial vegetation is a model of Posidonia oceanica seagrass species represented by slightly flexible polypropylene shoots with 8 artificial leaves of 0.28 and 0.16 m height. Different hydrodynamics conditions (Hs, Tp, water depth hw) and geometrical parameters (submergence ratio α, shoot density N) have been tested to see their influence on wave attenuation. For a high submergence ratio (typically 0.7), the wave attenuation can reach 67% of the incident wave height whereas for a low submergence ratio (< 0.2) the wave attenuation is negligible. From each experiment, a bulk drag coefficient has been extracted following the energy dissipation model for irregular non-breaking waves developed by Mendez and Losada (2004). This model, based on the assumption that the energy loss over the species meadow is essentially due to the drag force, takes into account both wave and vegetation parameter. Finally, we found an empirical relationship for Cd depending on 2 dimensionless parameters: the Reynolds and Keulegan-Carpenter numbers. These relationships are compared with other similar studies.

Sign in / Sign up

Export Citation Format

Share Document