Laser Clad Geometry: Experimental Observation and Geometric Modeling

2010 ◽  
Vol 148-149 ◽  
pp. 628-632 ◽  
Author(s):  
Zhi Jian Wang ◽  
Shi Yun Dong ◽  
Bin Shi Xu ◽  
Wei Xia
Keyword(s):  
Feed Rate ◽  
Geometric Modeling ◽  
Mass Conservation ◽  
Scanning Speed ◽  
Optical Microscope ◽  
Powder Feed Rate ◽  
Powder Feed ◽  
Simulation Based ◽  
Geometric Simulation ◽  
Theoretical Results

In this paper, a new analytical method of laser clad geometric simulation was developed. The effects of laser process parameters such as laser power, scanning speed, and powder feed rate on estimating clad geometry were investigated in this approach. A series of cladding was prepared by 1 kW diode pumping solid-state laser, to characterize the cross-section image of the clad by optical microscope. The clad profile was fitted by pitch arc and line in AutoCAD, with results displaying the arc-like upper profile of the clad. The theoretical results are discussed and compared with experimental data. The simulation based on the mass conservation is capable of predicting the clad width and depth with reasonable accuracy at medium powder feed rate.

Modeling of Transport Phenomena in the Laser Multilayered Cladding

2009 ◽  
Author(s):  
Fanrong Kong ◽  
Radovan Kovacevic
Keyword(s):  
Feed Rate ◽  
Molten Pool ◽  
Laser Power ◽  
Steel Powder ◽  
Mass Transfer Process ◽  
Scanning Speed ◽  
Heat Radiation ◽  
Powder Feed Rate ◽  
Transient Model ◽  
Powder Feed

The present work studies the heat and mass transfer process in the laser multilayered cladding of H13 tool steel powder by numerical modeling and experimental validation. A solid-liquid-gas unified transient model was developed to investigate the evolution of temperature distribution and flow velocity of the liquid phase in the molten pool. In this model, an enthalpy-porosity approach was applied to deal with the solidification and melting occurring in the clad, and a level-set method was used to track the evolution of the molten pool free surface. Moreover, heat loss due to forced convection and heat radiation and laser heat input occurring on the top surface of deposited layer and substrate have been incorporated into the source term of governing equations. The effects of laser power, scanning speed, and powder feed rate on the dilution and height of the multilayered clad are investigated based on the numerical model and experimental measurement. The results show that increasing the laser power and powder feed rate, or reducing the scanning speed, can increase the clad height and directly influence the remelted depth of each layer of deposition. The numerical results have a qualitative agreement with the experimental measurements.

scholarly journals Crack Sensitivity Control of Nickel-Based Laser Coating Based on Genetic Algorithm and Neural Network

Coatings ◽  
2019 ◽  
Vol 9 (11) ◽  
pp. 728 ◽  
Author(s):  
Yu ◽  
Sun ◽  
Huang ◽  
Wang ◽  
Wang ◽  
...  
Keyword(s):  
Neural Network ◽  
Genetic Algorithm ◽  
Laser Cladding ◽  
Process Parameters ◽  
Feed Rate ◽  
Crack Density ◽  
Scanning Speed ◽  
Powder Feed Rate ◽  
Powder Feed ◽  
Overlap Rate

This paper aimed to establish a nonlinear relationship between laser cladding process parameters and the crack density of a high-hardness, nickel-based laser cladding layer, and to control the cracking of the cladding layer via an intelligent algorithm. By using three main process parameters (overlap rate, powder feed rate, and scanning speed), an orthogonal experiment was designed, and the experimental results were used as training and testing datasets for a neural network. A neural network prediction model between the laser cladding process parameters and coating crack density was established, and a genetic algorithm was used to optimize the prediction results. To improve their prediction accuracy, genetic algorithms were used to optimize the weights and thresholds of the neural networks. In addition, the performance of the neural network was tested. The results show that the order of influence on the coating crack sensitivity was as follows: overlap rate > powder feed rate > scanning speed. The relative error between the predicted value and the experimental value of the three-group test genetic algorithm-optimized neural network model was less than 9.8%. The genetic algorithm optimized the predicted results, and the technological parameters that resulted in the smallest crack density were as follows: powder feed rate of 15.0726 g/min, overlap rate of 49.797%, scanning speed of 5.9275 mm/s, crack density of 0.001272 mm/mm2. Therefore, the amount of crack generation was controlled by the optimization of the neural network and genetic algorithm process.

scholarly journals Study on the Deformation Control and Microstructures of Thin-Walled Parts Repaired by Laser Cladding

Coatings ◽  
2020 ◽  
Vol 10 (4) ◽  
pp. 369 ◽  
Author(s):  
Jiangtong Yu ◽  
Wenlei Sun ◽  
Haibo Huang ◽  
Yong Huang
Keyword(s):  
Laser Cladding ◽  
Feed Rate ◽  
Laser Power ◽  
Visual Analysis ◽  
Scanning Speed ◽  
Powder Feed Rate ◽  
Dendritic Crystal ◽  
Powder Feed ◽  
Minimum Deformation ◽  
Thin Walled

To reduce the deformation and improve the quality of thin-walled parts repaired by laser cladding, a three-factor, three-level orthogonal experimental scheme was employed to clad Ni60 powder on thin-walled parts with a thickness of 3.5 mm. To measure the deformation of the thin-walled parts, a method of combining the meshing of the backs of the thin-walled parts and fixing one end of the parts during cladding was used. The effects of the powder feed rate, laser power, and scanning speed on the deformation of the thin-walled parts were studied via visual analysis and analysis of variance, and the process parameters that resulted in the minimum deformation were determined. The deformation process of the thin-walled parts and the causes of cladding stress were also studied, and the microstructure of the cladding layer with the minimum deformation was analyzed via scanning electron microscopy (SEM). The results reveal that the deformation of the thin-walled parts increased with the increase of laser power. The increases of the scanning speed and powder feed rate were found to reduce the deformation of thin-walled parts; the laser power was found to have a significant effect, and the powder feed rate was found to have no significant effect, on the deformation of thin-walled parts. The order of the influence of factors on the deformation of thin-walled parts from greatest to least was determined to be as follows: laser power > scanning speed > powder feed rate. The optimal parameters to obtain the minimum deformation and good metallurgical bonding of thin-walled parts were found to be a powder feed rate of 1.4 r/min, a laser power of 1100 W, and a scanning speed of 8 mm/s. From the bottom to the top, the crystal structure of the coating with the minimum deformation was found to be coarse dendrite, dendritic crystal, and equiaxed crystal.

Parametric investigation and characterization on SS316 built by laser-assisted directed energy deposition

2019 ◽  
Vol 234 (3) ◽  
pp. 452-466 ◽  
Author(s):  
K Benarji ◽  
Y Ravi Kumar ◽  
CP Paul ◽  
AN Jinoop ◽  
KS Bindra
Keyword(s):  
Deposition Rate ◽  
Process Parameters ◽  
Feed Rate ◽  
Laser Power ◽  
Energy Deposition ◽  
Scanning Speed ◽  
Powder Feed Rate ◽  
Parametric Investigation ◽  
Powder Feed ◽  
Directed Energy

In the present work, parametric investigation and characterization of stainless steel 316 (SS316) built by laser-assisted directed energy deposition (L-DED) is performed. Single-track L-DED experiments are carried by varying laser power, scanning speed, and powder feed rate using full factorial experimental design. The effect of L-DED process parameters on the track geometry, deposition rate, and microhardness is investigated, and three different combinations of process parameters yielding maximum deposition rate and hardness are identified for bulk investigation. The identified process parameters are laser power of 1000 W, powder feed rate of 8 g/min, and scanning speed of 0.4 m/min, 0.5 m/min, and 0.6 m/min. The austenitic phase [Formula: see text] is detected at all the conditions. However, ferrite [Formula: see text] peak is observed at 0.6 m/min due to microsegregation and thermal gradients. The minimum crystallite size is estimated to be 24.88 nm at 0.6 m/min. The porosity and microstructure analysis is carried out by optical microscopic images. The fine columnar dendritic structure is observed in L-DED samples at all conditions. An average microhardness of 317.4 HV0.98 N is obtained at 0.4 m/min, and it is observed that microhardness reduces with an increase in scanning speed mainly due to increase in lack of fusion and porosity. Tribology studies are carried out at different values of normal load and sliding velocity. The minimum specific wear rate of 0.02497 × 10−4 mm3/Nm is observed at scanning speed of 0.4 m/min. Scanning electron microscope of the wear tracks analysis shows abrasive wear as the major wear mechanism. This study provides a path for building SS316 components for various engineering applications.

Multi-Objective Optimisation of Laser Deposition of Metal Matrix Composites for Surface Coating Using Principal Component Analysis

2018 ◽  
Vol 40 ◽  
pp. 9-21 ◽  
Author(s):  
Peter Kayode Farayibi
Keyword(s):  
Feed Rate ◽  
Surface Coating ◽  
Laser Power ◽  
Traverse Speed ◽  
Laser Deposition ◽  
Powder Feed Rate ◽  
Multi Objective ◽  
Powder Feed ◽  
Output Characteristics ◽  
Wire Feed

Laser deposition is an advanced manufacturing technology capable of enhancing service life of engineering components by hard-facing their functional surfaces. There are quite a number of parameters involved in the process and also desirable output characteristics. These output characteristics are often independently optimised and which may lead to poor outcome for other characteristics, hence the need for multi-objective optimisation of all the output characteristics. In this study, a laser deposition of Ti-6Al-4V wire and tungsten carbide powder was made on a Ti-6Al-4V substrate with a view to achieve a metallurgical bonded metal matrix composite on the substrate. Single clads were deposited with a desire to optimise the composite clad characteristics (height, width and reinforcement fraction) for the purpose of surface coating. Processing parameters (laser power, traverse speed, wire feed rate, powder feed rate) were varied, the experiment was planned using Taguchi method and output characteristics were analysed using principal component analysis approach. The results indicated that the parameters required for optimised clad height, width, and reinforcement fraction necessary for surface coating is laser power of 1800 W, traverse speed of 200 mm/min, wire feed rate 700 mm/min and powder feed rate of 30 g/min. The powder feed rate was found to most significantly contribute 43.99%, followed by traverse speed 39.77%, laser power 15.87% with wire feed rate having the least contribution towards the multi-objective optimisation. Confirmation results showed that clad width and reinforcement fraction were significantly improved by the optimised parameters. The multi-objective optimisation procedure is a useful tool necessary to identify the process factors required to enhance output characteristics in laser processing.

Novel Liquid Fuel HVOF Torches Fueled with Ethanol: Optimization and Erosion Wear Response of Cr3C2-NiCr Coatings

2021 ◽  
Author(s):  
Shaowu Liu ◽  
Michel Moliere ◽  
Hanlin Liao
Keyword(s):  
Flow Rate ◽  
Feed Rate ◽  
Impact Angle ◽  
Oxygen Flow Rate ◽  
Oxygen Flow ◽  
Standoff Distance ◽  
Wear Loss ◽  
Erosion Wear ◽  
Powder Feed Rate ◽  
Powder Feed

Abstract In this work; a novel liquid fuel HVOF process fueled with ethanol was used to prepare 75wt%Cr3C2–25wt%NiCr coatings on AISI304 stainless steel substrate. Taguchi method was employed to optimize the spray parameters (ethanol flow rate; oxygen flow rate; powder feed rate and standoff distance) to achieve better erosion resistance at 90° impact angle. The results indicated that ethanol flow rate and oxygen flow rate were identified as the highly contributing parameters on the erosion wear loss. The important sequence of the spray parameter is ethanol flow rate > oxygen flow rate > standoff distance > powder feed rate. The optimal spray parameter (OSP) for minimum erosion wear loss was obtained under ethanol flow rate of 28slph; oxygen flow rate of 420slpm; powder feed rate of 76.7 g/min and standoff distance of 300mm. The phase composition; microstructure; hardness; porosities; and the erosion wear behaviors of the coatings have been studied in detail. Besides; erosion wear testing of the optimized coating was conducted at 30°; 60° and 90° impact angle using air jet erosion testing machine. The SEM images of the erodent samples were taken to analyze the erosion mechanism.

scholarly journals Effects of Powder Feed Rate on Formation of Fully Equiaxed β Grains in Titanium Alloys Fabricated by Directed Energy Deposition

Metals ◽  
2020 ◽  
Vol 10 (4) ◽  
pp. 521 ◽  
Author(s):  
Qiang Zhang ◽  
Siyu Zhang ◽  
Min Zheng ◽  
Yongchao Ou ◽  
Shang Sui ◽  
...  
Keyword(s):  
Feed Rate ◽  
Molten Pool ◽  
Cellular Structure ◽  
Energy Deposition ◽  
Grain Morphology ◽  
Thermal Conditions ◽  
Powder Feed Rate ◽  
Powder Feed ◽  
Directed Energy Deposition ◽  
Directed Energy

A near β titanium alloy, Ti5Al2Sn2Zr4Mo4Cr, was fabricated by directed energy deposition (DED) with different powder feed rates to investigate the formation of fully equiaxed β grains. A two-dimensional numerical model was developed to investigate the thermal conditions of the molten pool. Experimental results showed that the formation of an epitaxial cellular structure at the bottom of the molten pool is almost unavoidable. An increase in the powder feed rate produces a moderate thermal condition and promotes the formation of equiaxed grains in a single cladding layer. However, it could not guarantee the formation of a fully equiaxed microstructure in a block sample. From a low to high powder feed rate, fully columnar, mixed equiaxed–columnar, and fully equiaxed microstructures were obtained. Grain morphology was also affected by the remolten process. Increasing the powder feed rate reduced the remolten depth and broke the continuity of the epitaxial cellular structure, leading to different grain morphologies.

Laser Alloying with WC Ceramic Powder in Hot Work Tool Steel Using a High Power Diode Laser (HPDL)

2006 ◽  
Vol 15-17 ◽  
pp. 193-198 ◽  
Author(s):  
Marek Piec ◽  
Leszek Adam Dobrzański ◽  
Krzysztof Labisz ◽  
Ewa Jonda ◽  
Andrzej Klimpel
Keyword(s):  
Surface Layer ◽  
Tungsten Carbide ◽  
Diode Laser ◽  
Tool Steel ◽  
High Power ◽  
Feed Rate ◽  
Powder Feed Rate ◽  
Powder Feed ◽  
Power Diode ◽  
High Power Diode Laser

Investigations include alloying the X38CrMoV5-3 hot-work tool steel surface layer with the tungsten carbide, using the high power diode laser (HPDL). The tungsten carbide ceramic particles of the medium grain size according to FSSS = 50 /m were introduced using the rotor conveyer to improve the properties of the surface layer. The powder feed rate was set at the steady level of 8.64g/min. Remelting and alloying were carried out several times in the laser power range of 1.2 – 2.3 kW in the remelting/alloying, alloying/remelting sequences. The structural mechanism was determined of gradient layer development, effect was studied of alloying parameters, gas protection method, and powder feed rate on its mechanical properties, and especially on its hardness, abrasive wear resistance, and roughness. Structure changes were revealed consisting, in particular, in its refining, and also hardness and microhardness changes in comparizon to the nonremelted steel. Examination results obtained with the EDX microanalysis, surface and linear analysis of the chemical composition, as well as the X-ray qualitative phase analysis are presented.

Processing parameter, microstructure and hardness of Ni base intermetallic alloy coating fabricated by laser cladding

MRS Advances ◽  
2017 ◽  
Vol 2 (26) ◽  
pp. 1381-1386 ◽  
Author(s):  
Takeshi Okuno ◽  
Yasuyuki Kaneno ◽  
Takuto Yamaguchi ◽  
Takayuki Takasugi ◽  
Satoshi Semboshi ◽  
...  
Keyword(s):  
Laser Cladding ◽  
Feed Rate ◽  
Laser Power ◽  
Alloy Coating ◽  
Intermetallic Alloy ◽  
Ingot Metallurgy ◽  
Processing Parameter ◽  
Powder Feed Rate ◽  
Cladding Layer ◽  
Powder Feed

ABSTRACTNi base intermetallic alloy coating was fabricated by laser cladding, controlling the laser power and powder feed rate. Atomized powder of the Ni base intermetallic alloy was laser-cladded on the substrate of stainless steel 304. The hardness and microstructure of the clad layers were investigated by Vickers hardness test, SEM, XRD and TEM observations. The hardness of the cladding layer was affected by the dilution with the substrate; it increased with decreasing laser power and increasing powder feed rate. By optimizing the dilution with the substrate, the cladding layer with an almost identical hardness level to that of the Ni base intermetallic alloy fabricated by ingot metallurgy was obtained. The TEM observations revealed that a very fine-sized microstructure composed of Ni3Al and Ni3V was partially formed even in the as-cladded state. After annealing, the two-phase microstructure composed of Ni3Al and Ni3V was developed in the cladding layer, resulting in enhanced hardness in the cladding layers fabricated in the majority of cladding conditions.

Sign in / Sign up

Export Citation Format

Share Document