Automatic On-Line Detection and Sorting System Design and Implementation for Paper-Making Printing

2011 ◽  
Vol 383-390 ◽  
pp. 3-5 ◽  
Author(s):  
Rong Xia Sun ◽  
Lei Gao ◽  
Jian Kang ◽  
Pan Pan Huang ◽  
Yi Tian ◽  
...  
Keyword(s):  
Signal Detection ◽  
High Speed ◽  
Pulse Signal ◽  
Automatic Testing ◽  
Sensor Signal ◽  
Paper Making ◽  
On Line ◽  
Code Identification ◽  
Production Requirement ◽  
Sorting System

Transforms the papermaking production line to spurt the code automatic detection separation system is the production of impending rapid requirement. This design using the original paper cutter to cut the paper separating function is bad, choose the trigger for separating door action by photoelectric sensor signal, triggering bad signal detection equipments, and complete code identification papers in the test paper separating bad logo. In printing, the PLC control high-speed counter acquisition traction, printing roll encoder pulse signal range. This system includes color standard sensor signal detection, Siemens S7-200 PLC controller, etc. Also gives the system installation problems and presents the corresponding countermeasures. The paper realize online automatic testing equipments, satisfying the function of separation, stable, zero leakage rate of selected control of the production requirement.

The on-line use of histogram data for high-speed correction and alignment of electron microscope images

1984 ◽  
Vol 42 ◽  
pp. 556-557
Author(s):  
William Krakow
Keyword(s):  
Power Spectrum ◽  
High Speed ◽  
Direct Memory Access ◽  
Digital Television ◽  
Contrast Transfer Function ◽  
The Past ◽  
High Resolution Tem ◽  
On Line ◽  
Correction Of Astigmatism ◽  
The Fourier Transform

In the past few years on-line digital television frame store devices coupled to computers have been employed to attempt to measure the microscope parameters of defocus and astigmatism. The ultimate goal of such tasks is to fully adjust the operating parameters of the microscope and obtain an optimum image for viewing in terms of its information content. The initial approach to this problem, for high resolution TEM imaging, was to obtain the power spectrum from the Fourier transform of an image, find the contrast transfer function oscillation maxima, and subsequently correct the image. This technique requires a fast computer, a direct memory access device and even an array processor to accomplish these tasks on limited size arrays in a few seconds per image. It is not clear that the power spectrum could be used for more than defocus correction since the correction of astigmatism is a formidable problem of pattern recognition.

Microwave On-Line Measurements on Conveyed Products Application to Paper and Wood Industries

1994 ◽  
Vol 347 ◽  
Author(s):  
J.Ch. Bolomey ◽  
G. Cottard ◽  
P. Berthaud ◽  
A. Lemaitre ◽  
J. F. Portala
Keyword(s):  
High Speed ◽  
Transformation Process ◽  
Wood Material ◽  
Quantitative Measurements ◽  
On Line ◽  
Phase Data ◽  
Polynomial Expansions ◽  
Physical Quantities ◽  
Data Calibration

ABSTRACTMicrowave multiport sensors have been shown to provide some unique capabilities to achieve real-time testing of products conveyed at high speed. In many applications, quantitative measurements of physical quantities such as moisture content, density, etc… are required, either to guarantee reliable production or to optimally control a fabrication/transformation process. In this paper, different ways of extracting such physical quantities from microwave measurements performed by multiport sensors are presented. Model approaches are used, based on polynomial expansions of the physical quantities to be measured as a function of the microwave amplitude and phase data. Calibration procedures have been investigated for both paper and wood material samples. Comparisons between in-situ, microwave and conventional, measurements are analysed.

Design, Construction and Control of a Remotely Operated Vehicle (ROV)

2011 ◽  
Author(s):  
Alireza Marzbanrad ◽  
Jalil Sharafi ◽  
Mohammad Eghtesad ◽  
Reza Kamali
Keyword(s):  
High Speed ◽  
Degrees Of Freedom ◽  
Remotely Operated Vehicle ◽  
Six Degrees Of Freedom ◽  
Depth Sensors ◽  
Control Schemes ◽  
On Line ◽  
Operation Unit ◽  
And Control ◽  
Design Construction

This is report of design, construction and control of “Ariana-I”, an Underwater Remotely Operated Vehicle (ROV), built in Shiraz University Robotic Lab. This ROV is equipped with roll, pitch, heading, and depth sensors which provide sufficient feedback signals to give the system six degrees-of-freedom actuation. Although its center of gravity and center of buoyancy are positioned in such a way that Ariana-I ROV is self-stabilized, but the combinations of sensors and speed controlled drivers provide more stability of the system without the operator involvement. Video vision is provided for the system with Ethernet link to the operation unit. Control commands and sensor feedbacks are transferred on RS485 bus; video signal, water leakage alarm, and battery charging wires are provided on the same multi-core cable. While simple PI controllers would improve the pitch and roll stability of the system, various control schemes can be applied for heading to track different paths. The net weight of ROV out of water is about 130kg with frame dimensions of 130×100×65cm. Ariana-I ROV is designed such that it is possible to be equipped with different tools such as mechanical arms, thanks to microprocessor based control system provided with two directional high speed communication cables for on line vision and operation unit.

Predicting paper making defects on-line using data mining

1998 ◽  
Vol 11 (5-6) ◽  
pp. 331-338 ◽  
Author(s):  
Robert Milne ◽  
Mike Drummond ◽  
Patrick Renoux
Keyword(s):  
Data Mining ◽  
Paper Making ◽  
On Line ◽  
Using Data

Design and Implementation of the Cold-Rolled Aluminum Plate Surface On-Line Defect Detection System

2013 ◽  
Vol 712-715 ◽  
pp. 2323-2326
Author(s):  
Xing Guang Qi ◽  
Hai Lun Zhang ◽  
Xiao Ting Li
Keyword(s):  
High Speed ◽  
Surface Defects ◽  
Detection System ◽  
Aluminum Plate ◽  
Gigabit Ethernet ◽  
Accurate Detection ◽  
High Processing Speed ◽  
Rolled Aluminum ◽  
On Line ◽  
Cold Rolled

This paper presents an on-line surface defects detection system based on machine vision, which has high speed architecture and can perform high accurate detection for cold-rolled aluminum plate. The system consists of high speed camera and industrial personal computer (IPC) array which connected through Gigabit Ethernet, achieved seamless detection by redundant control. In order to acquire high processing speed, single IPC as processor receives from and deals with only one or two cameras' image. Experimental results show that the system with high accurate detection capability can satisfy the requirement of real time detection and find out the defects on the production line effectively.

A Study on the Method of Vibration Analysis for Korean High Speed Train by the On-Line Test

2006 ◽  
Vol 321-323 ◽  
pp. 1593-1596 ◽  
Author(s):  
Chan Kyoung Park ◽  
Ki Whan Kim ◽  
Jin Yong Mok ◽  
Young Guk Kim ◽  
Seog Won Kim
Keyword(s):  
Vibration Analysis ◽  
High Speed ◽  
Vibration Mode ◽  
Dynamic Performance ◽  
Railway Vehicle ◽  
High Speed Train ◽  
Acceleration Data ◽  
On Line ◽  
System Vibration ◽  
Line Test

The Korean High Speed Train (KHST) has been tested on the Kyongbu high speed line and the Honam conventional line since 2002. A data acquisition system was developed to test and prove the dynamic performance of the KHST, and the system has been found to be very efficient in acquiring multi-channel data from accelerometers located all over the train. Also presented in this paper is an analysis procedure which is simple and efficient in analyzing the acceleration data acquired during the on-line test of the KHST. The understanding of system vibration mode for a railway vehicle is essential to evaluate the characteristics of a dynamic system and to diagnose the dynamic problems of the vehicle system during tests and operations. Methods based on homogeneous linear systems are not realistic because real systems have nonlinear characteristics and are strongly dependent on environmental conditions. In this paper an efficient method of vibration analysis has been proposed and applied for the KHST to evaluate its vibration mode characteristics. The results show that this method is suitable to estimate the system vibration modes of the KHST.

Sign in / Sign up

Export Citation Format

Share Document