Influence of pH on the Morphology and Luminescence Properties of Europium-Doped Hydroxyapatite Nanoparticles

2011 ◽  
Vol 391-392 ◽  
pp. 1132-1137
Author(s):  
Su Ping Huang ◽  
Jun Zhu ◽  
Ke Chao Zhou
Keyword(s):  
Photoelectron Spectroscopy ◽  
Inductively Coupled Plasma ◽  
Doping Concentration ◽  
Ph Value ◽  
Luminescence Properties ◽  
X Ray Diffraction ◽  
X Ray ◽  
Inductively Coupled ◽  
Ph Values ◽  
Influence Of Ph

Luminescence behaviors and morphology of Eu3+doped hydroxyapatite synthesized under different pH values were well investigated by X-ray diffraction (XRD), scanning electronic microscopy (SEM), X-ray photoelectron spectroscopy (XPS), Inductively Coupled Plasma (ICP) (ICP–PLASMA 1000), and photoluminescence (PL) spectroscopy. Results revealed that With pH values increased from 6.5 to 10.0, the morphology of nano-Eu:HA particles changes from rod particles to equiaxed particles. The actual doping concentration and aspect ratio of Eu3+-doped HA decreased with the increasing of pH value. At the same time, the fluorescence intensity also tends to weakly lower with the increasing of pH value, which indicated that the luminescence properties mainly depended on the actual Eu3+doping concentration, the influences of morphology on the luminescence properties were slight.

scholarly journals Generalized Methodology for Inserting Metal Heteroatoms into the Layered Zeolite Precursor RUB-36 by Interlayer Expansion

Crystals ◽  
2020 ◽  
Vol 10 (6) ◽  
pp. 530 ◽  
Author(s):  
Chaoqun Bian ◽  
Xiao Wang ◽  
Lan Yu ◽  
Fen Zhang ◽  
Jie Zhang ◽  
...  
Keyword(s):  
Photoelectron Spectroscopy ◽  
Inductively Coupled Plasma ◽  
Catalytic Performance ◽  
X Ray Diffraction ◽  
Zeolite Sample ◽  
X Ray ◽  
Inductively Coupled ◽  
Temperature Programmed ◽  
First Time ◽  
N2 Sorption

The incorporation of metal heteroatoms into zeolites is an effective modification strategy for enhancing their catalytic performance. Herein, for the first time we report a generalized methodology for inserting metal heteroatoms (such as Sn, Fe, Zn, and Co) into the layered zeolite precursor RUB-36 via interlayer expansion by using the corresponding metal acetylacetate salt. Through this generalized methodology, Sn-JHP-1, Fe-JHP-1, Zn-JHP-1 and Co-JHP-1 zeolites could be successfully prepared by the reaction of RUB-36 and corresponding metal acetylacetate salt at 180 °C for 24 h in the presence of HCl solution. As a typical example, Sn-JHP-1 and calcined Sn-JHP-1 (Sn-JHP-2) zeolite is well characterized by the X-ray diffraction (XRD), diffuse reflectance ultraviolet-visible (UV-Vis), inductively coupled plasma (ICP), N2 sorption, temperature-programmed-desorption of ammonia (NH3-TPD) and X-ray photoelectron spectroscopy (XPS) techniques, which confirm the expansion of adjacent interlayers and thus the incorporation of isolated Sn sites within the zeolite structure. Notably, the obtained Sn-JHP-2 zeolite sample shows enhanced catalytic performance in the conversion of glucose to levulinic acid (LA) reaction.

scholarly journals Fe-Containing MOFs as Seeds for the Preparation of Highly Active Fe/Al-SBA-15 Catalysts in the NAlkylation of Aniline

Molecules ◽  
2019 ◽  
Vol 24 (15) ◽  
pp. 2695 ◽  
Author(s):  
Mhadmhan ◽  
Marquez-Medina ◽  
Romero ◽  
Reubroycharoen ◽  
Luque
Keyword(s):  
Photoelectron Spectroscopy ◽  
Inductively Coupled Plasma ◽  
Catalytic Performance ◽  
Alkylation Reaction ◽  
X Ray Diffraction ◽  
X Ray ◽  
Inductively Coupled ◽  
Highly Active ◽  
Milling Method ◽  
Plasma Mass Spectrometry

We have successfully incorporated iron species into mesoporous aluminosilicates (AlSBA15) using a simple mechanochemical milling method. The catalysts were characterized by nitrogen physisorption, inductively coupled plasma mass spectrometry (ICP-MS), pyridine (PY) and 2,6-dimethylpyridine (DMPY) pulse chromatography titration, powder X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS) and scanning electron microscopy with energy-dispersive X-ray spectroscopy (SEM-EDX). The catalysts were tested in the N-alkylation reaction of aniline with benzyl alcohol for imine production. According to the results, the iron sources, acidity of catalyst and reaction conditions were important factors influencing the reaction. The catalyst showed excellent catalytic performance, achieving 97% of aniline conversion and 96% of imine selectivity under optimized conditions.

Two-Phase Structure of Fluorinated Powdered Silica Resulting from Deep Processing of Rice Wastes

2018 ◽  
Vol 7 (1) ◽  
pp. 38-44 ◽  
Author(s):  
А. Рашковский ◽  
A. Rashkovskiy ◽  
Е. Политова ◽  
E. Politova ◽  
А. Меркушкин ◽  
...  
Keyword(s):  
Photoelectron Spectroscopy ◽  
Inductively Coupled Plasma ◽  
Physicochemical Analysis ◽  
Nano Particles ◽  
Deep Processing ◽  
X Ray Diffraction ◽  
Two Phase ◽  
X Ray ◽  
Inductively Coupled ◽  
Two Phases

In this investigation the structure of «green» silica maid with rice husk has been studied by methods of physicochemical analysis. By method of X-ray diffraction it has been found that the samples of «green» silica powders are completely amorphous, and the observed amorphous halo consists of two components. By method of scanning electron microscopy it has been revealed that nano-particles of «green» SiO2 can form agglomerates and microstructures with dimensions from 0,1 to 500 microns, containing numerous pores, which presence has been confirmed by sorption measurements. By method of mass spectrometry with inductively coupled plasma has been found the presence of aluminum, titanium and nickel mechanical impurities in the «green» SiO2 powders. By method of X-ray photoelectron spectroscopy significant amount of fluorine atoms in «green» silica (up to 5% (at.)) has been revealed, which could be introduced in SiO2 in the process of its preparation. In such a case, it was found that fluorine interacts with «green» silica by means of two mechanisms, leading to appearance of two phases within fluorinated powders of «green» SiO2.

Preparation, Characterization and Conductivity of Solid High-Proton Conductor Na7[CoW11O39Cd(H2O)]·12H2O

2014 ◽  
Vol 937 ◽  
pp. 224-228 ◽  
Author(s):  
Li Qiang Chen ◽  
Xiu Mei Lin ◽  
Ming Xia Zhu ◽  
Li Mei Dai
Keyword(s):  
Photoelectron Spectroscopy ◽  
Inductively Coupled Plasma ◽  
Proton Conductor ◽  
X Ray Diffraction ◽  
X Ray ◽  
Inductively Coupled ◽  
High Proton ◽  
Electrode Method ◽  
Dta Curve ◽  
First Time

A new solid high-proton conductor Na7[CoW11O39Cd (H2O)]·12H2O has been synthesized for the first time. The percentage composition of the product were determined by Inductively coupled plasma (ICP) and X-ray photoelectron spectroscopy (XPS). The product was characterized by infrared spectroscopy (IR) and X-ray diffraction (XRD), which indicate it possesses the Keggin structure. The TG-DTA curve shows the sequence of water loss in the compound, the amount of the loss, as well as the thermostability. Conductivity of the compound was investigated by four-electrode method at room temperature and different measuring temperatures, the results reveal that its proton conductivity is 4.87×10−4S·cm-1at 27oC and the activation energy for proton conduction is 15.31 kJ/mol.

scholarly journals Study on synthesizing Mg/Al layered double hydroxides at different pHs

2014 ◽  
Vol 15 ◽  
pp. 36-39 ◽  
Author(s):  
E Otgonjargal ◽  
G Burmaa ◽  
B Enkhmaa ◽  
M Enkhtuul ◽  
L Nyam-Ochir ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Ph Value ◽  
Infrared Analysis ◽  
X Ray Diffraction ◽  
X Ray ◽  
Ph Values ◽  
Double Hydroxide ◽  
Double Hydroxides ◽  
Influence Of Ph ◽  
Scanning Electron

Mg/Al layered double hydroxide (LDH) was successfully synthesized at different pHs values. The Mg/AL LDH was well characterized by X-Ray diffraction and Fourier transform infrared analysis. The morphology of the LDH was observed using Scanning electron microscopy with energy dispersive X-ray spectroscopy. The influence of pH values on the morphology of the Mg/Al LDHs were studied. The result showed that the well-synthesized Mg/Al LDHs could be obtained when the pH value was about 10.0 at room temperature.DOI: http://doi.dx.org/10.5564/mjc.v15i0.319 Mongolian Journal of Chemistry 15 (41), 2014, p36-39

Preparation and Characterization of Na7[CoCrW11O39(H2O)]·15H2O for Electrical Conductivity

2015 ◽  
Vol 733 ◽  
pp. 292-295
Author(s):  
Bei Ping Yang ◽  
Li Qiang Chen ◽  
Xiu Mei Lin ◽  
Ming Xia Zhu
Keyword(s):  
Photoelectron Spectroscopy ◽  
Inductively Coupled Plasma ◽  
Proton Conductor ◽  
X Ray Diffraction ◽  
X Ray ◽  
Inductively Coupled ◽  
Electrode Method ◽  
Dta Curve ◽  
First Time

A new solid proton conductor Na7[CoCrW11O39 (H2O)]·15H2O has been synthesized for the first time. The percentage composition of the product were determined by inductively coupled plasma (ICP) and X-ray photoelectron spectroscopy (XPS). The product was characterized by infrared spectroscopy (IR) and X-ray diffraction (XRD), which indicate it possesses the Keggin structure. The TG-DTA curve shows the sequence of water loss in the compound, the amount of the loss, as well as the thermostability. Conductivity of the compound was investigated by four-electrode method at room temperature and different measuring temperatures, the results reveal that its proton conductivity is 9.42×10−7S·cm-1 at 25°C.

SYNTHESIS AND CHARACTERIZATION OF TERNARY AL-C-N COMPOUND

2002 ◽  
Vol 16 (06n07) ◽  
pp. 1132-1137 ◽  
Author(s):  
N. JIANG ◽  
S. XU ◽  
K. N. OSTRIKOV ◽  
E. L. TSAKADZE ◽  
J. D. LONG ◽  
...  
Keyword(s):  
Photoelectron Spectroscopy ◽  
Inductively Coupled Plasma ◽  
Optical Emission ◽  
Flow Rate Ratio ◽  
In Situ Observation ◽  
X Ray Diffraction ◽  
X Ray ◽  
Inductively Coupled

An attempt for modification of carbon nitride material by introduction of Al to form a ternary Al-C-N compound in a thin film deposited using inductively coupled plasma (ICP) assisted DC magnetron sputtering is reported. Optical emission spectroscopy (OES) is used for in-situ observation and identification of reactive species. The films were characterized using x-ray photoelectron spectroscopy (XPS) and x-ray diffraction spectroscopy (XRD). The results indicate that C-N bond is formed in the plasma. The XPS narrow scam spectra confirm the existence of C-Al, sp2C-N and sp3C-N bonds. Elemental proportion of carbon increases with the CH4/N2 flow rate ratio, and has a tendency to saturate. The film is dominated by c-AlN (111), mixed with Al4C3 and AlCN ternary compound.

scholarly journals Crystalline/Amorphous Blend Identification from Cobalt Adsorption by Layered Double Hydroxides

Materials ◽  
2018 ◽  
Vol 11 (9) ◽  
pp. 1706 ◽  
Author(s):  
Lin Chi ◽  
Zheng Wang ◽  
Yuan Sun ◽  
Shuang Lu ◽  
Yan Yao
Keyword(s):  
Photoelectron Spectroscopy ◽  
Inductively Coupled Plasma ◽  
Ph Value ◽  
Precipitation Process ◽  
X Ray ◽  
Adsorption Mechanisms ◽  
Inductively Coupled ◽  
Co Precipitation ◽  
Double Hydroxide ◽  
Double Hydroxides

In this study, the adsorption behavior of CaAl-Cl layered double hydroxide (CaAl-Cl-LDH) with a controlled pH value (pH = 6) on Co(II) ions ([Co] = 8 mM) is investigated. The comprehensively accepted mechanism of cobalt adsorption on LDH is considered to be co-precipitation, and the final adsorbed products are normally crystalline Co-LDH. One unanticipated finding is that crystalline/amorphous blends are found in the X-ray diffraction (XRD) pattern of Co-adsorbed LDH. To shed light on the adsorption products and the mechanisms in the adsorption process of Co(II) in an aqueous solution by CaAl-Cl-LDH, a series of testing methods including Fourier-transform infrared spectroscopy (FT-IR), Scanning electron microscope (SEM), High-resolution transmission electron microscopy (HR-TEM), X-ray photoelectron spectroscopy (XPS), and inductively coupled plasma (ICP) are applied to clarify the interaction between cobalt and CaAl-Cl-LDH. According to the comprehensive analysis, the formation of the crystalline/amorphous blends corresponds to two adsorption mechanisms. The crystalline phases are identified as Co6Al2CO3(OH)16·4H2O, which is attributed to the co-precipitation process occurring in the interaction between Co(II) and CaAl-Cl-LDH. The formation of the amorphous phases is due to surface complexation on amorphous Al(OH)3 hydrolyzed from CaAl-Cl-LDH.

scholarly journals Green Synthesis of CuInS2/ZnS Nanocrystals with High Photoluminescence and Stability

2015 ◽  
Vol 2015 ◽  
pp. 1-9 ◽  
Author(s):  
Min Fu ◽  
Weiling Luan ◽  
Shan-Tung Tu ◽  
Leslaw Mleczko
Keyword(s):  
Photoelectron Spectroscopy ◽  
Inductively Coupled Plasma ◽  
Shell Growth ◽  
Optical Emission ◽  
Growth Time ◽  
X Ray Diffraction ◽  
X Ray ◽  
Inductively Coupled ◽  
Transmission Electron ◽  
Zns Nanocrystals

Highly photoluminescent core/shell CuInS2/ZnS (CIS/ZnS) nanocrystals were synthesized. Zinc acetate and dodecanethiol in octadecene solvent were used for shell growth. The structure and composition of QDs were investigated with inductively coupled plasma-optical emission spectroscopy, X-ray photoelectron spectroscopy, and transmission electron microscopy. The crystal phase of CIS was tetragonal chalcopyrite. Based on X-ray diffraction analysis, it has been concluded that the growth of the ZnS shell did not affect the phase structure of CuInS2(CIS). Photoluminescence (PL) quantum yield (QY) of CIS increased to 80% after epitaxial growth of ZnS, and the PL emission wavelength can be feasibly tuned to be in the range of 560–710 nm by adjusting shell growth time. The superb photostability with high PL QY of CIS/ZnS nanocrystals is ascribed to the gradient of the chemical composition that has been formed between the core and the shell.

Study on Influence of Silicate Morphology Based on pH Value

2012 ◽  
Vol 454 ◽  
pp. 324-328
Author(s):  
Yan He ◽  
Ya Jing Liu ◽  
Yong Lin Cao ◽  
Li Xia Zhou
Keyword(s):  
Silicic Acid ◽  
Ph Value ◽  
Colorimetric Method ◽  
Absorption Spectrometry ◽  
Degree Of Polymerization ◽  
Raw Material ◽  
X Ray Diffraction ◽  
X Ray ◽  
Ph Values ◽  
The Stability

Infra-red absorption spectrometry, X-ray diffraction observations and characterization tests based on silicon molybdenum colorimetric method were used to investigate the optimal pH value controlling the stability of the silicic acid form. The experiment process was done by using sodium silicate as raw material. The results showed that the solution of silicate influenced the polymerization. The active silicic acid solution with a certain degree of polymerization was obtained by controlling the pH values.

Sign in / Sign up

Export Citation Format

Share Document