Sheet Single Point Vibration Incremental Forming Process Simulation and Analysis of Process Parameters

2012 ◽  
Vol 430-432 ◽  
pp. 74-78 ◽  
Author(s):  
Gai Pin Cai ◽  
Cong Wen Xing ◽  
Zhi Hong Jiang ◽  
Zhong Kai Zhang
Keyword(s):  
Sheet Metal ◽  
Incremental Forming ◽  
Single Point ◽  
Product Yield ◽  
Simulation Software ◽  
Forming Force ◽  
Forming Process ◽  
Vibration Parameters ◽  
The Right ◽  
Theory Research

The deformation of vibration incremental forming process for sheet metal is in high complexity, theory research is not perfect. This subject using DEFORM simulation software, joined the vibration on the forming process of tool head and simulated the forming process base on different tool radius and vibration parameters. Simulation result indicated that vibration in greatly reduced the stress of the forming tool head. The right vibration parameters smoothed out the forming force largely, reduced sheet metal stress concentration, improved product quality and product yield. That has a higher degree of study and use value.

Finite Element Analysis of Incremental Sheet Forming for Metal Sheet

2018 ◽  
Vol 783 ◽  
pp. 148-153
Author(s):  
Muhammad Sajjad ◽  
Jithin Ambarayil Joy ◽  
Dong Won Jung
Keyword(s):  
Mechanical Properties ◽  
Sheet Metal ◽  
Tool Path ◽  
Incremental Forming ◽  
Single Point ◽  
Machining Process ◽  
Machining Parameters ◽  
Forming Process ◽  
Element Analysis ◽  
Tool Diameter

Incremental sheet metal forming, is a non-conventional machining process which offers higher formability, flexibility and low cost of production than the traditional conventional forming process. Punch or tool used in this forming process consecutively forces the sheet to deform locally and ultimately gives the target profile. Various machining parameters, such as type of tool, tool path, tool size, feed rate and mechanical properties of sheet metal, like strength co-efficient, strain hardening index and ultimate tensile strength, effects the forming process and the formability of final product. In this research paper, Single Point Incremental Forming was simulated using Dassault system’s Abaqus 6.12-1 and results are obtained. Results of sheet profile and there change in thickness is investigated. For this paper, we simulated the process in abaqus. The tool diameter and rotational speed is find out for the production of parts through incremental forming. The simulation is done for two type of material with different mechanical properties. Various research papers were used to understand the process of incremental forming and its simulation.

scholarly journals Simulation of incremental forming processes of a pyramidal ring made of two materials

2018 ◽  
Vol 19 (3) ◽  
pp. 313
Author(s):  
Masood Ghassabi ◽  
Milad Salimi ◽  
Mohammad Haghpanahi
Keyword(s):  
Feed Rate ◽  
Rotational Speed ◽  
Incremental Forming ◽  
Thickness Distribution ◽  
Single Point ◽  
Dimensional Accuracy ◽  
Cnc Machine ◽  
Forming Force ◽  
Forming Process ◽  
Dimensional Precision

Incremental forming is one of the most well-known forming processes for complex and asymmetric parts. This method uses a CNC machine, simple forming tool, and a die. This study focused on effects of some parameters such as the material, feed rate, pitch, rotational speed and movement strategy of tool on the dimensional precision, forming force, thickness distribution and fracture in the welding area. The results showed that single point incremental forming (SPIF) led to a better thickness distribution with lower tool force, whereas two-point incremental forming led to better dimensional accuracy. Rotational speed does not have any significant impact on the forming process while decreasing the feed rate partially reduced the forming force. According to the results, although dimensional precision in double point incremental forming is better than SPIF, when it comes to the thickness distribution, forming force, and economic issues, SPIF is in favor. The results also showed that by connecting two materials, different parameters for the two materials could be investigated simultaneously in one simulation process.

scholarly journals Common defects of parts manufactured through single point incremental forming

2021 ◽  
Vol 343 ◽  
pp. 04007
Author(s):  
Mihai Popp ◽  
Gabriela Rusu ◽  
Sever-Gabriel Racz ◽  
Valentin Oleksik
Keyword(s):  
Sheet Metal ◽  
Metal Forming ◽  
Incremental Forming ◽  
Single Point ◽  
Single Point Incremental Forming ◽  
Forming Process ◽  
Metal Forming Process ◽  
Serial Robot ◽  
The Many ◽  
Cold Metal

Single point incremental forming is one of the most intensely researched die-less manufacturing process. This process implies the usage of a CNC equipment or a serial robot which deforms a sheet metal with the help of a relatively simple tool that follows an imposed toolpath. As every cold metal forming process, besides the many given advantages it has also some drawbacks. One big drawback in comparison with other cold metal forming processes is the low accuracy of the deformed parts. The aim of this research is to investigate the sheet metal bending mechanism through finite element method analysis. The results shows that the shape of the retaining rings has a big influence over the final geometrical accuracy of the parts manufactured through single point incremental forming.

Experimental Study on Residual Formability of Single Point Incrementally Formed Part

2019 ◽  
Author(s):  
Chetan P. Nikhare
Keyword(s):  
Sheet Metal ◽  
Sheet Metal Forming ◽  
Metal Forming ◽  
Incremental Forming ◽  
Thickness Distribution ◽  
Single Point ◽  
Forming Limit ◽  
Single Point Incremental Forming ◽  
Forming Process ◽  
Conventional Process

Abstract A substantial increase in demand on the sheet metal part usage in aerospace and automotive industries is due to the increase in the sale of these products to ease the transportation. However, due to the increase in fuel prices and further environmental regulation had left no choice but to manufacture more fuel efficient and inexpensive vehicles. These heavy demands force researchers to think outside the box. Many innovative research projects came to replace the conventional sheet metal forming of which single point incremental forming is one of them. SPIF is the emerging die-less sheet metal forming process in which the single point tool incrementally forces any single point of sheet metal at any processing time to undergo plastic deformation. It has several advantages over the conventional process like high process flexibility, elimination of die, complex shape and better formability. Previous literature provides enormous research on formability of metal during this process, process with various metals and hybrid metals, the influence of various process parameter, but residual formability after this process is untouched. Thus, the aim of this paper is to investigate the residual formability of the formed parts using single point incremental forming and then restrike with a conventional tool. The common process parameters of single point incremental forming were varied, and residual formability was studied through the conventional process. The strain and thickness distribution were measured and analyzed. In addition, the forming limit of the part was plotted and compared.

Effect of Toolpath on the Springback of 2024-T3 Aluminum During Single Point Incremental Forming

2015 ◽  
Author(s):  
Zachary C. Reese ◽  
Brandt J. Ruszkiewicz ◽  
Chetan P. Nikhare ◽  
John T. Roth
Keyword(s):  
Residual Stresses ◽  
Sheet Metal ◽  
Tool Path ◽  
Incremental Forming ◽  
Single Point ◽  
Final Part ◽  
Cnc Milling ◽  
Forming Process ◽  
Step Size ◽  
Part Geometry

Incremental forming is a nontraditional forming method in which a spherical tool is used to asymmetrically deform sheet metal without the need for expensive allocated dies. Incremental forming employs a tool path similar to that used when CNC milling. Hence, when forming a part, the forming tool makes a series of passes circumferentially around the workpiece, gradually spirally stepping down in the z-axis on each sequential pass. This tool path deforms the sheet metal stock into the final, desired shape. These passes can start from the outer radius of the part and work in (Out to In, OI forming) or they can start from the center of the shape and work outward (In to Out, IO forming). As with many sheet metal operations, springback is a big concern during the incremental forming process. During the deformation process, residual stresses are created within the workpiece causing the final formed shape to springback when it is unclamped, sometimes very significantly. The more complex the geometry of the final part and the more total deformation that occurs when forming the geometry, the greater the residual stresses that are generated within the part. The residual stresses that have built up in the piece cause more significant distortion to the part when it is released from the retaining fixturing. This paper examines how the step size (in the z direction), OI vs. IO forming, and final part geometry affect the total springback in a finished piece. For all of these tests 0.5 mm thick sheets of 2024-T3 aluminum were used to form both the truncated pyramid and truncated cone shape. From this investigation it was found that smaller step sizes result in greater springback, IO is significantly less effective in forming the part (due to workpiece tearing), and final part geometry plays an important role due to the creation of residual stresses that exist in corners.

Drilled Hole Technique for Created Single Point Incremental Forming Limited Diagram

2015 ◽  
Vol 658 ◽  
pp. 177-181
Author(s):  
Kittiphat Rattanachan
Keyword(s):  
Sheet Metal ◽  
Incremental Forming ◽  
Single Point ◽  
Material Behavior ◽  
304 Stainless Steel ◽  
Single Point Incremental Forming ◽  
Forming Process ◽  
Steel Blank ◽  
Etching Technique ◽  
Drilling Hole

To produce the forming limited diagram for predicting and studying material behavior in sheet metal forming, grid etching or grid marking on blank surface are applied before forming. But in single point incremental forming process, sheet metal blanks are subjected to highly strain or highly deformation which the conventional gridding is no longer to be occurred on the surface of formed part. And some material such as titanium, nickel based alloy etc are difficulty to etch the grid marks on its surface. So this paper is proposed the drilling hole technique to substitute with the grid etching technique in single point incremental forming process. The holes 2 mm. diameter were drilled on the SUS 304 stainless steel blank before forming. The deformed holes are calculated as true major strain and true minor strain and plot into a forming limited diagram. The results are compared with the conventional etching techniques which show an according trend. The drilling hole technique could be used in study the material behavior in single point incremental forming, it a low cost convenient and easy than grid etching technique.

scholarly journals Tool Path Design of the Counter Single Point Incremental Forming Process to Decrease Shape Error

Materials ◽  
2020 ◽  
Vol 13 (21) ◽  
pp. 4719
Author(s):  
Kyu-Seok Jung ◽  
Jae-Hyeong Yu ◽  
Wan-Jin Chung ◽  
Chang-Whan Lee
Keyword(s):  
Sheet Metal ◽  
Tool Path ◽  
Incremental Forming ◽  
Single Point ◽  
Optimization Method ◽  
Single Point Incremental Forming ◽  
Shape Error ◽  
Forming Process ◽  
Two Stage ◽  
Shape Errors

Incremental sheet metal forming can manufacture various sheet metal products without a dedicated punch and die set. In this study, we developed a two-stage incremental forming process to decrease shape errors in the conventional incremental forming process. The forming process was classified into the first single point incremental forming (1st SPIF) process for forming a product and the counter single point incremental forming (counter SPIF) process to decrease shape error. The counter SPIF gives bending deformation in the opposite direction. Furthermore, the counter SPIF compensates for shape errors, such as section deflection, skirt spring-back, final forming height, and round. The tool path of the counter SPIF has been optimized through a relatively simple optimization method by modifying the tool path of the previous step. The tool path of the 1st SPIF depends on the geometry of the product. An experiment was performed to form a circular cup shape to verify the proposed tool path of the 1st and counter SPIF. The result confirmed that the shape error decreased when compared to the conventional SPIF. For the application, the ship-hull geometry was adopted. Experimental results demonstrated the feasibility of the two-stage incremental forming process.

Compensations for Tool Path to Enhance Accuracy During Double Sided Incremental Forming

2015 ◽  
Author(s):  
Rakesh Lingam ◽  
Anirban Bhattacharya ◽  
Javed Asghar ◽  
N. Venkata Reddy
Keyword(s):  
Sheet Metal ◽  
Sheet Metal Forming ◽  
Metal Forming ◽  
Tool Path ◽  
Incremental Forming ◽  
Single Point ◽  
Three Dimensional ◽  
Geometric Accuracy ◽  
Forming Process ◽  
Incremental Sheet Metal Forming

Incremental Sheet Metal Forming (ISMF) is a flexible sheet metal forming process that enables forming of complex three dimensional components by successive local deformations without using component specific tooling. ISMF is also regarded as die-less manufacturing process and in the absence of part-specific dies, geometric accuracy of formed components is inferior to that of their conventional counterparts. In Single Point Incremental Forming (SPIF), the simplest variant of ISMF, bending near component opening region is unavoidable due to lack of support. The bending in the component opening region can be reduced to a larger extent by another variant of ISMF namely Double Sided Incremental Forming (DSIF) in which a moving tool is used to support the sheet locally at the deformation zone. However the overall geometry of formed components still has unacceptable deviation from the desired geometry. Experimental observation and literature indicates that the supporting tool loses contact with the sheet after forming certain depth. Present work demonstrates a methodology to enhance geometric accuracy of formed components by compensating for tool and sheet deflection due to forming forces. Forming forces necessary to predict compensations are obtained using force equilibrium method along with thickness calculation methodology developed using overlap that occurs during forming (instead of using sine law). Results indicate that there is significant improvement in accuracy of the components produced using compensated tool paths.

Numerical Simulation for the Multi-Point Incremental Forming Process

2015 ◽  
Vol 775 ◽  
pp. 219-223
Author(s):  
Wan Mian Yang ◽  
Yuan Xin Luo ◽  
Zhi Fang Liu ◽  
Ru Xu Du
Keyword(s):  
Numerical Simulation ◽  
Finite Element ◽  
Finite Element Model ◽  
Sheet Metal ◽  
Incremental Forming ◽  
Element Model ◽  
Sheet Metals ◽  
Forming Force ◽  
Forming Process ◽  
Thickness Change

Multi-point forming process has been developed to shape the sheet metal with bidirectional curvature. However, the forming force usually climbs too high so that the dimension of the forming machine should be designed to meet it. To solve this problem, the multi-point incremental forming (MPIF) process was proposed in this paper. First, the principle of this new forming process was introduced. Then, the experimental device was designed. Next, the MPIF process was simulated by a finite element model. The forming effects including displacements, thickness, and curvatures were visualized and discussed in detail. It was found that there is no obvious thickness change during the forming process. The advantage of this forming process is that the shape of the sheet metals adaptable and controllable with small forming force.

The Effected of Single Point Incremental Forming Process Parameters on the Formed Part Surface Roughness

2014 ◽  
Vol 979 ◽  
pp. 335-338
Author(s):  
Kittiphat Rattanachan ◽  
Chatchapol Chungchoo
Keyword(s):  
Surface Roughness ◽  
Sheet Metal ◽  
Process Parameters ◽  
Feed Rate ◽  
Incremental Forming ◽  
Single Point ◽  
Single Point Incremental Forming ◽  
Tool Rotational Speed ◽  
Forming Process ◽  
Inner Surface

The single point incremental forming process (SPIF) are suited for sheet metal prototyping, because it is a low cost production process that produces sheet metal part without any used of die, and easy to adjust the part’s geometry by change toolpath. But the quality of forming parts is still in doubt. In some applications, such as mould cavity for rapid mould and the medical parts, in this case the inside surface roughness plays an importance role. In this paper, the SPIF process parameters that affected to the inner surface roughness were experimental studied. The investigated parameters are composing of tool feed rate, side overlap, depth step and tool radius. The 2k-p factorial experimental design was used to analyze the interaction between each parameter. The results showed that increasing feed rate and depth step decreased inner surface roughness. Reducing tool rotational speed and feed rate reduced inner surface roughness. So increasing depth step with decreasing side overlap reduced inner surface roughness. The large tool radius and lower side overlap improved inner surface roughness. The large tool radius and higher depth step improved inner surface roughness. And last, reducing tool rotational speed with larger tool radius, the inner surface roughness is decreased.

Sign in / Sign up

Export Citation Format

Share Document