scholarly journals Simulation of incremental forming processes of a pyramidal ring made of two materials

2018 ◽  
Vol 19 (3) ◽  
pp. 313
Author(s):  
Masood Ghassabi ◽  
Milad Salimi ◽  
Mohammad Haghpanahi
Keyword(s):  
Feed Rate ◽  
Rotational Speed ◽  
Incremental Forming ◽  
Thickness Distribution ◽  
Single Point ◽  
Dimensional Accuracy ◽  
Cnc Machine ◽  
Forming Force ◽  
Forming Process ◽  
Dimensional Precision

Incremental forming is one of the most well-known forming processes for complex and asymmetric parts. This method uses a CNC machine, simple forming tool, and a die. This study focused on effects of some parameters such as the material, feed rate, pitch, rotational speed and movement strategy of tool on the dimensional precision, forming force, thickness distribution and fracture in the welding area. The results showed that single point incremental forming (SPIF) led to a better thickness distribution with lower tool force, whereas two-point incremental forming led to better dimensional accuracy. Rotational speed does not have any significant impact on the forming process while decreasing the feed rate partially reduced the forming force. According to the results, although dimensional precision in double point incremental forming is better than SPIF, when it comes to the thickness distribution, forming force, and economic issues, SPIF is in favor. The results also showed that by connecting two materials, different parameters for the two materials could be investigated simultaneously in one simulation process.

scholarly journals Evaluation of the Formability and Dimensional Accuracy Improvement of Ti6Al4V in Warm SPIF Processes

Metals ◽  
2019 ◽  
Vol 9 (3) ◽  
pp. 272 ◽  
Author(s):  
Jesús Naranjo ◽  
Valentín Miguel ◽  
Alberto Martínez ◽  
Juana Coello ◽  
María Manjabacas
Keyword(s):  
High Performance ◽  
Incremental Forming ◽  
Single Point ◽  
Dimensional Accuracy ◽  
Design Stage ◽  
Forming Process ◽  
Accuracy Improvement ◽  
Dimensional Precision ◽  
Heating Device ◽  
Surface Finishes

Single Point Incremental Forming (SPIF) has great potential as it can be easily implemented and the forming process does not require the use of dies. However, its application to high performance alloys such as Ti6Al4V has not been resolved due to its characteristic low formability. In the literature, studies on the warm SPIF process applied to this alloy report improved formability. However, in some of these studies the procedures used are complex and in others the surface finishes obtained are unsatisfactory. The present study proposes a methodology consisting of a simple heating device which permits working at moderate temperatures and quantifies the benefit of the temperature on the alloy formability, the forces acting during the process, and finally the dimensional precision of the parts produced. Working temperatures in the range of 300–400 °C significantly reduce forces, increase formability of the alloy, and substantially reduce springback. However, the springback values suggest the need for dimensional compensation at the design stage of products.

Thickness Distribution and Forming Strategy Analysis for Two Point Incremental Forming with a Male Die

2011 ◽  
Vol 337 ◽  
pp. 452-455 ◽  
Author(s):  
Zhao Bing Liu ◽  
Paul Meehan ◽  
Paul Bellette
Keyword(s):  
Incremental Forming ◽  
Low Cost ◽  
Thickness Distribution ◽  
Single Point ◽  
Three Dimensional ◽  
Dimensional Accuracy ◽  
Strategy Analysis ◽  
Multi Stage ◽  
Analytical Perspective ◽  
Forming Strategy

Incremental Sheet Forming (ISF) is a promising sheet-metal-forming technology which is drawing more and more researchers’ attention due to its flexibility of manufacturing three-dimensional products at a relatively low cost for rapid prototyping and small-batch production. This paper is focused on the thickness distribution and the forming strategy analysis for two point incremental forming with a male die. The analyzed benchmark is half a torus which is generated by revolving a semi-circle. Such a part is hardly able to be formed by single point incremental forming because its slope varies from 0 degree to 90 degrees. In terms of the varying slope, the variant of sine’s law is derived to give an approximate prediction of the thickness distribution from an analytical perspective. In addition, a multi-stage forming strategy is proposed in order to form the part successfully. In particular, a keying operation is implemented carefully in order to avoid twist phenomenon and achieve good dimensional accuracy.

Formability of aluminum 5083 friction stir welded blank in two-point incremental forming process

2017 ◽  
Vol 232 (3) ◽  
pp. 267-280 ◽  
Author(s):  
Pejman Ebrahimzadeh ◽  
Hamid Baseri ◽  
Mohammad J Mirnia
Keyword(s):  
Incremental Forming ◽  
Single Point ◽  
Dimensional Accuracy ◽  
Welding Parameters ◽  
Forming Process ◽  
Minimum Thickness ◽  
Friction Stir ◽  
Series Of Experiments ◽  
Rotary Speed ◽  
Aluminum 5083

In the present study, an attempt was made to analyze the formability of aluminum 5083 fiction stir welded blank through an incremental forming process. Experiments are performed on the joints which were fabricated by optimal welding parameters with 73% strength sufficiency. Firstly, a series of experiments were carried out to compare the formability of welded blank in single-point and two-point incremental forming operations, under different wall angles. Thereafter, an experimental study based on response surface methodology was carried out to find out the effect of incremental forming factors on the dimensional accuracy and minimum thickness. It was found from the results that irrespective of the wall angle, the formability of welded blank (i.e. forming height until occurrence of tear) which formed in two-point incremental forming process is relatively higher than that of single-point incremental forming. Also, statistical analysis revealed that tool rotary speed and step down has a significant effect on the critical thickness, while springback is affected by the sequence of tool rotary speed and feed rate.

Experimental Study on Residual Formability of Single Point Incrementally Formed Part

2019 ◽  
Author(s):  
Chetan P. Nikhare
Keyword(s):  
Sheet Metal ◽  
Sheet Metal Forming ◽  
Metal Forming ◽  
Incremental Forming ◽  
Thickness Distribution ◽  
Single Point ◽  
Forming Limit ◽  
Single Point Incremental Forming ◽  
Forming Process ◽  
Conventional Process

Abstract A substantial increase in demand on the sheet metal part usage in aerospace and automotive industries is due to the increase in the sale of these products to ease the transportation. However, due to the increase in fuel prices and further environmental regulation had left no choice but to manufacture more fuel efficient and inexpensive vehicles. These heavy demands force researchers to think outside the box. Many innovative research projects came to replace the conventional sheet metal forming of which single point incremental forming is one of them. SPIF is the emerging die-less sheet metal forming process in which the single point tool incrementally forces any single point of sheet metal at any processing time to undergo plastic deformation. It has several advantages over the conventional process like high process flexibility, elimination of die, complex shape and better formability. Previous literature provides enormous research on formability of metal during this process, process with various metals and hybrid metals, the influence of various process parameter, but residual formability after this process is untouched. Thus, the aim of this paper is to investigate the residual formability of the formed parts using single point incremental forming and then restrike with a conventional tool. The common process parameters of single point incremental forming were varied, and residual formability was studied through the conventional process. The strain and thickness distribution were measured and analyzed. In addition, the forming limit of the part was plotted and compared.

STUDY ON FORMING FORCES OF PARTS PROCESSED BY SINGLE POINT INCREMENTAL FORMING WITH DUMMY SHEET

2019 ◽  
Vol 14 (3) ◽  
Author(s):  
Vikas Sisodia ◽  
Shailendra Kumar
Keyword(s):  
Process Parameters ◽  
Feed Rate ◽  
Incremental Forming ◽  
Single Point ◽  
Sheet Thickness ◽  
Single Point Incremental Forming ◽  
Forming Force ◽  
Step Size ◽  
Wall Angle ◽  
Influence Of Process Parameters

The present paper describes the experimental investigation on influence of process parameters on maximum forming force in Single Point Incremental Forming (SPIF) process using dummy sheet. Process parameters namely dummy sheet thickness, tool size, step size, wall angle and feed rate are selected. Taguchi L18 orthogonal array is used to design the experiments. From the analysis of variance (ANOVA) dummy sheet thickness, tool size, step size and wall angle are significant process parameters while feed rate is insignificant. It is found that as dummy sheet thickness, tool size, step size and wall angle increase magnitude of peak forming force increases while there is marginal decrease in forming force as feed rate increases. Predictive model is also developed for forming force. Validation tests are performed in order to check the accuracy of developed model. Optimum set of process parameters is also determined to minimize forming force. Experimental results are in good agreement with results predicted by the developed mathematical model.

Sheet Single Point Vibration Incremental Forming Process Simulation and Analysis of Process Parameters

2012 ◽  
Vol 430-432 ◽  
pp. 74-78 ◽  
Author(s):  
Gai Pin Cai ◽  
Cong Wen Xing ◽  
Zhi Hong Jiang ◽  
Zhong Kai Zhang
Keyword(s):  
Sheet Metal ◽  
Incremental Forming ◽  
Single Point ◽  
Product Yield ◽  
Simulation Software ◽  
Forming Force ◽  
Forming Process ◽  
Vibration Parameters ◽  
The Right ◽  
Theory Research

The deformation of vibration incremental forming process for sheet metal is in high complexity, theory research is not perfect. This subject using DEFORM simulation software, joined the vibration on the forming process of tool head and simulated the forming process base on different tool radius and vibration parameters. Simulation result indicated that vibration in greatly reduced the stress of the forming tool head. The right vibration parameters smoothed out the forming force largely, reduced sheet metal stress concentration, improved product quality and product yield. That has a higher degree of study and use value.

Experimental Tests to Study Feasibility and Formability in Incremental Forming Process

2009 ◽  
Vol 410-411 ◽  
pp. 391-400 ◽  
Author(s):  
Aldo Attanasio ◽  
Elisabetta Ceretti ◽  
Antonio Fiorentino ◽  
Luca Mazzoni ◽  
Claudio Giardini
Keyword(s):  
Tool Path ◽  
Incremental Forming ◽  
Single Point ◽  
Sheet Thickness ◽  
Experimental Tests ◽  
Final Part ◽  
Cnc Machine ◽  
Forming Process ◽  
Metal Forming Process ◽  
Sheet Formability

This paper deals with Incremental Sheet Forming (ISF), a sheet metal forming process, that knew a wide development in the last years. It consists of a simple hemispherical tool that, moving along a defined path by means of either a CNC machine or a robot or a self designed device, locally deforms a metal sheet. A lot of experimental and simulative researches have been conducted in this field with different aims: to study the sheet formability and part feasibility as a function of the process parameters; to define models able to forecast the final sheet thickness as a function of the drawing angle and tool path strategy; to understand how the sheet deforms and how formability limits can be defined. Nowadays, a lot of these topics are still open. In this paper, the results obtained from an experimental campaign performed to study sheet formability and final part feasibility are reported. The ISF tests were conducted deforming FeP04 deep drawing steel sheet 0.8 mm thick and analyzing the influence of the tool path strategy and of the adopted ISF technique (Single Point Incremental Forming Vs. Two Points Incremental Forming). The part feasibility and formability were evaluated considering final sheet thickness, geometrical errors of the final part, maximum wall angle and depth at which the sheet breaks. Moreover, process forces measurements were carried out by means of a specific device developed by the Authors, allowing to obtain important information about the load acting on the deforming device and necessary for deforming sheet.

The Effected of Single Point Incremental Forming Process Parameters on the Formed Part Surface Roughness

2014 ◽  
Vol 979 ◽  
pp. 335-338
Author(s):  
Kittiphat Rattanachan ◽  
Chatchapol Chungchoo
Keyword(s):  
Surface Roughness ◽  
Sheet Metal ◽  
Process Parameters ◽  
Feed Rate ◽  
Incremental Forming ◽  
Single Point ◽  
Single Point Incremental Forming ◽  
Tool Rotational Speed ◽  
Forming Process ◽  
Inner Surface

The single point incremental forming process (SPIF) are suited for sheet metal prototyping, because it is a low cost production process that produces sheet metal part without any used of die, and easy to adjust the part’s geometry by change toolpath. But the quality of forming parts is still in doubt. In some applications, such as mould cavity for rapid mould and the medical parts, in this case the inside surface roughness plays an importance role. In this paper, the SPIF process parameters that affected to the inner surface roughness were experimental studied. The investigated parameters are composing of tool feed rate, side overlap, depth step and tool radius. The 2k-p factorial experimental design was used to analyze the interaction between each parameter. The results showed that increasing feed rate and depth step decreased inner surface roughness. Reducing tool rotational speed and feed rate reduced inner surface roughness. So increasing depth step with decreasing side overlap reduced inner surface roughness. The large tool radius and lower side overlap improved inner surface roughness. The large tool radius and higher depth step improved inner surface roughness. And last, reducing tool rotational speed with larger tool radius, the inner surface roughness is decreased.

scholarly journals Investigation the Effect of Process Variables on the Formability of Parts Processed by Single Point Incremental Forming

2019 ◽  
Vol 14 (2) ◽  
pp. 58-70
Author(s):  
Adil Shbeeb Jabber
Keyword(s):  
Feed Rate ◽  
Metal Forming ◽  
Single Point ◽  
Effective Strain ◽  
Image Processing Technique ◽  
Cnc Machine ◽  
Forming Process ◽  
Step Size ◽  
Forming Angle ◽  
Incremental Step

Incremental sheet metal forming process is an advanced flexible manufacturing process to produce various 3D products without using dedicated tool as in conventional metal forming. There are a lot of process parameters that have effect on this process, studying the effect of some parameters on the strain distributions of the product over the length of deformation is the aim of this study. In order to achieve this goal, three factors (tool forming shape, feed rate and incremental step size) are examined depending on three levels on the strain distributions over the wall of the product. Strain measurement was accomplished by using image processing technique using MATALB program. The significance of the control factors are explored using two statistical methods:  analysis of variance (ANOVA) and main effect plot (MEP). All experiments were carried out on a sheet of Aluminum alloy (Al1050) with thickness 0.9 mm by using 3 axes CNC machine to produce frustum pyramid product. The result showed that the feed rate is a parameter that has large effect on the values of the effective strain percentage contribution of (42.86% and 51.42%), respectively, and is followed by step size (25.1% and 30.60%) percentage contributions and finally the tool shape with (21.79% and 10.54%) on the (55° and 45°) wall angle, respectively. The maximum and minimum average effective strain computed on the 55◦ forming angle were (0.580 and 0.399), respectively. Finally, the maximum and minimum average effective strain computed on the 45◦ forming angle were equal to (0.412 and 0.324), respectively.

Sign in / Sign up

Export Citation Format

Share Document