Tool Inclination Angle Change Rate Control in Five-Axis Flat-End Milling

2012 ◽  
Vol 488-489 ◽  
pp. 819-825
Author(s):  
Gandjar Kiswanto ◽  
Vinsensius Ricko ◽  
S. Suntoro
Keyword(s):  
Inclination Angle ◽  
Tool Path ◽  
End Milling ◽  
Machined Surface ◽  
Good Surface ◽  
Angle Change ◽  
Wide Range ◽  
The One ◽  
Good Surface Roughness ◽  
Five Axis

Five-axis milling is used in the machining of complex shaped surfaces in a wide range of industries. In five-axis milling, one can adjust inclination angle to adapt such machining condition, e.g. to give high material removal and/or to avoid gouging. Choosing an appropriate inclination angle is difficult especially for complex parts with varying surface curvature. On the one hand, a small inclination angle is recommended to have good surface roughness and small scallop height. On the other hand, some regions may need much larger minimum inclination angle compared to the others to avoid gouging. The trade off for this is to have, in practice, a varying minimum (which is considered to be optimal) inclination angle along the tool path, so that while machining, the tool is dynamically adapted to be as close as possible to the surface without gouging. However, applying inclination angle change over some distances influences the quality of machined surface. This paper presented a method to control such inclination angle change to improve part accuracy. Some experimental were conducted to see the results and compared with the one when inclination angle change is not controled. The propose method effectively reduces the surface deviation thus improve part accuracy. More details about this study are presented in the paper.

Micro Flat End Milling Simulation Model With Instantaneous Plowing Area Prediction

2016 ◽  
Vol 4 (2) ◽  
Author(s):  
Abdolreza Bayesteh ◽  
Junghyuk Ko ◽  
Martin Byung-Guk Jun
Keyword(s):  
Feed Rate ◽  
Tool Path ◽  
End Milling ◽  
Chip Thickness ◽  
Depth Of Cut ◽  
Uncut Chip Thickness ◽  
Chip Area ◽  
Edge Radius ◽  
Wide Range ◽  
Radial Depth

There is an increasing demand for product miniaturization and parts with features as low as few microns. Micromilling is one of the promising methods to fabricate miniature parts in a wide range of sectors including biomedical, electronic, and aerospace. Due to the large edge radius relative to uncut chip thickness, plowing is a dominant cutting mechanism in micromilling for low feed rates and has adverse effects on the surface quality, and thus, for a given tool path, it is important to be able to predict the amount of plowing. This paper presents a new method to calculate plowing volume for a given tool path in micromilling. For an incremental feed rate movement of a micro end mill along a given tool path, the uncut chip thickness at a given feed rate is determined, and based on the minimum chip thickness value compared to the uncut chip thickness, the areas of plowing and shearing are calculated. The workpiece is represented by a dual-Dexel model, and the simulation properties are initialized with real cutting parameters. During real-time simulation, the plowed volume is calculated using the algorithm developed. The simulated chip area results are qualitatively compared with measured resultant forces for verification of the model and using the model, effects of cutting conditions such as feed rate, edge radius, and radial depth of cut on the amount of shearing and plowing are investigated.

scholarly journals Optimisation of Planning Parameters for Machining Blade Electrode Micro-Fillet with Scallop Height Modelling

Micromachines ◽  
2021 ◽  
Vol 12 (3) ◽  
pp. 237
Author(s):  
Yue Liu ◽  
Zhanqiang Liu ◽  
Wentong Cai ◽  
Yukui Cai ◽  
Bing Wang ◽  
...  
Keyword(s):  
Path Planning ◽  
Tilt Angle ◽  
Tool Path ◽  
End Milling ◽  
Tool Path Planning ◽  
Scallop Height ◽  
Aero Engine ◽  
Tool Tilt Angle ◽  
Five Axis ◽  
Height Model

Aero-engine blades are manufactured by electroforming process with electrodes. The blade electrode is usually machined with five-axis micromilling to get required profile roughness. Tool path planning parameters, such as cutting step and tool tilt angle, have a significant effect on the profile roughness of the micro-fillet of blade electrode. In this paper, the scallop height model of blade electrode micro-fillet processed by ball-end milling cutter was proposed. Effects of cutting step and tool tilt angle the machined micro-fillet profile roughness were predicted with the proposed scallop height model. The cutting step and tool tilt angle were then optimised to ensure the contour precision of the micro-fillet shape requirement. Finally, the tool path planning was generated and the machining strategy was validated through milling experiments. It was also found that the profile roughness was deteriorated due to size effect when the cutting step decreased to a certain value.

Surface Roughness Analysis for Radius End Mill in Cross Feed Direction Both Contour and Scanning Line Machinings

2020 ◽  
Author(s):  
Hirohisa Narita
Keyword(s):  
Surface Roughness ◽  
Inclination Angle ◽  
End Milling ◽  
Contour Line ◽  
End Mill ◽  
Good Surface ◽  
Corner Radius ◽  
Feed Direction ◽  
Scanning Line ◽  
Influence Degree

Abstract An optimum experimental condition, which realize good surface roughness in cross direction both contour and scanning lines, for radius end mill against some inclined surfaces is obtained and some features is these cutting processes is discussed in this paper. The optimum experimental condition, which consists of cutting type (or feed direction), spindle speed, feed rate, depth of immersion, inclination angle, corner radius of end mill and cross feed, is obtained and the influence degree of these parameters is calculated by using Taguchi method. The experiment is carried out based on L18 orthogonal array. Based on the influence degree and geometric contact status due to unique shape of radius end mill, some feature of radius end milling is introduced. As a result of the contour line machining, a scallop height is very influenced by the inclination angle and the corner radius, and surface machined by bottom edge must not be remained. Regarding the scanning line machining, “go-up” is good for the feed direction. Big corner radius is also suitable because side edge does not contact to workpiece. In other words, the cutting force in radial direction becomes small. Furthermore, the surface roughness of the scanning line machining is smaller than the one of the contour line machining.

Surface Integrity Studies in Ball End Milling of Thin Shaped Cantilever Inconel 718

2014 ◽  
Author(s):  
Nandkumar N. Bhopale ◽  
Raju S. Pawade
Keyword(s):  
Surface Integrity ◽  
Inconel 718 ◽  
Tool Path ◽  
Surface Defects ◽  
End Milling ◽  
Surface Region ◽  
Lower Surface ◽  
Machined Surface ◽  
Ball End Milling ◽  
Integrity Analysis

The paper presents the surface integrity analysis in ball end milling of thin shaped cantilever plate of Inconel 718. It is noticed that the workpiece deflection has significantly contributed to machined surface integrity in terms of surface topography and subsurface microhardness. The ball end milling performed with 15° workpiece inclination with horizontal tool path produced higher surface integrity which varies with the location of machined surface region. In general, the mid portion of the machined plate shows lower surface roughness and microhardness with less surface defects.

scholarly journals Influence of Chatter of VMC Arising During End Milling Operation and Cutting Conditions on Quality of Machined Surface

1970 ◽  
Vol 2 (1) ◽  
Author(s):  
A.K.M.N. Amin, M.A. Rizal, and M. Razman
Keyword(s):  
Surface Roughness ◽  
Metal Cutting ◽  
Metal Removal ◽  
End Milling ◽  
Cutting Speed ◽  
Cutting Conditions ◽  
End Mill ◽  
Machined Surface ◽  
Operating Cycle ◽  
Wide Range

Machine tool chatter is a dynamic instability of the cutting process. Chatter results in poor part surface finish, damaged cutting tool, and an irritating and unacceptable noise. Exten¬sive research has been undertaken to study the mechanisms of chatter formation. Efforts have been also made to prevent the occurrence of chatter vibration. Even though some progress have been made, fundamental studies on the mechanics of metal cutting are necessary to achieve chatter free operation of CNC machine tools to maintain their smooth operating cycle. The same is also true for Vertical Machining Centres (VMC), which operate at high cutting speeds and are capable of offering high metal removal rates. The present work deals with the effect of work materials, cutting conditions and diameter of end mill cutters on the frequency-amplitude characteristics of chatter and on machined surface roughness. Vibration data were recorded using an experimental rig consisting of KISTLER 3-component dynamometer model 9257B, amplifier, scope meters and a PC.  Three different types of vibrations were observed. The first type was a low frequency vibration, associated with the interrupted nature of end mill operation. The second type of vibration was associated with the instability of the chip formation process and the third type was due to chatter. The frequency of the last type remained practically unchanged over a wide range of cutting speed.  It was further observed that chip-tool contact processes had considerable effect on the roughness of the machined surface.Key Words: Chatter, Cutting Conditions, Stable Cutting, Surface Roughness.

Tool Orientation Planning in Milling With Process Dynamic Constraints: A Minimax Optimization Approach

2018 ◽  
Vol 140 (11) ◽  
Author(s):  
Tao Huang ◽  
Xiao-Ming Zhang ◽  
Jürgen Leopold ◽  
Han Ding
Keyword(s):  
Tool Path ◽  
End Milling ◽  
Tool Path Generation ◽  
Optimization Approach ◽  
Path Generation ◽  
Tool Orientation ◽  
Minimax Optimization ◽  
Ball End Milling ◽  
Dynamic Constraints ◽  
Five Axis

In five-axis milling process, the tool path generated by a commercial software seldom takes the dynamics of the machining process into account. The neglect of process dynamics may lead to milling chatter, which causes overcut, quick tool wear, etc., and thus damages workpiece surface and shortens tool life. This motivates us to consider dynamic constraints in the tool path generation. Tool orientation variations in five-axis ball-end milling influence chatter stability and surface location error (SLE) due to the varying tool-workpiece immersion area and cutting force, which inversely provides us a feasible and flexible way to suppress chatter and SLE. However, tool orientations adjustment for suppression of chatter and SLE may cause drastic changes of the tool orientations and affects surface quality. The challenge is to strike a balance between the smooth tool orientations and suppression of chatter and SLE. To overcome the challenge, this paper presents a minimax optimization approach for planning tool orientations. The optimization objective is to obtain smooth tool orientations, by minimizing the maximum variation of the rotational angles between adjacent cutter locations, with constraints of chatter-free and SLE threshold. A dedicated designed ball-end milling experiment is conducted to validate the proposed approach. The work provides new insight into the tool path generation for ball-end milling of sculpture surface; also it would be helpful to decision-making for process parameters optimization in practical complex parts milling operations at shop floor.

Synthesis of Cutting Tool Placement, Orientation and Motion Based on Surface Analysis

2000 ◽  
Author(s):  
C. G. Jensen ◽  
J. K. Hill ◽  
K. A. White
Keyword(s):  
Tool Path ◽  
Cutting Tool ◽  
A Priori ◽  
Cutting Tools ◽  
Detection Algorithm ◽  
Detection Methods ◽  
Machined Surface ◽  
Mathematical Basis ◽  
Five Axis ◽  
Verification Techniques

Abstract Engineers and designers use a wide variety of curve and surface formulations to describe products. The process of producing the physical shape of these products has remained essentially unchanged for many years. Traditionally, the process of finish surface machining has been error prone and inefficient due in large part to the mathematical basis used to control the positioning, orientation and movement of cutting tools in five-axis machining centers. This paper presents swept silhouette curvature matching algorithms for positioning and orienting a cutter such that tool and surface curvatures match. Formulations are given for both flat and filleted end mill cutters. The benefits of curvature matching are: reduction of local machining errors, reduction or elimination of grinding of the finished machined surface, and the improvement of machine tool efficiency. Examples are given that compare curvature matching to traditional machining methods. The paper concludes by discussing current research into a priori gouge detection methods based on intersection contact between the cutting tool and the design surface or the lower tolerance-bound offset surface to the design surface. An a priori gouge detection algorithm is necessary for the development of optimal tool motion and the reduction of time spent in tool path editing and verification. Techniques involving collinear normals, Bézier clipping, triangulation, normal intersection and swept volumes are suggested as techniques for examining the positional and translational tool gouge problem.

Sensitivity Analysis of Error Motions and Geometric Errors in the Case of Sphere-Shaped Workpiece

2020 ◽  
Author(s):  
Zongze Li ◽  
Ryuta Sato ◽  
Keiichi Shirase
Keyword(s):  
Sensitivity Analysis ◽  
Machine Tools ◽  
End Milling ◽  
Geometric Errors ◽  
Machined Surface ◽  
Error Sources ◽  
Motion Error ◽  
Machining Center ◽  
Machining Errors ◽  
Five Axis

Abstract Motion error of machine tool feed axes influences the machined workpiece accuracy. However, the influences of each error sources are not identical; some errors do not influence the machined surface although some error have significant influences. In addition, five-axis machine tools have more error source than conventional three-axis machine tools, and it is very tough to predict the geometric errors of the machined surface. This study proposes a method to analyze the relationships between the each error sources and the error of the machined surface. In this study, a kind of sphere-shaped workpiece is taken as a sample to explain how the sensitivity analysis makes sense in ball-end milling. The results show that the method can be applied for the axial errors, such as motion reversal errors, to make it clearer to obverse the extent of each errors. In addition, the results also show that the presented sensitivity analysis is useful to investigate that how the geometric errors influence the sphere surface accuracy. It can be proved that the presented method can help the five-axis machining center users to predict the machining errors on the designed surface of each axes error motions.

scholarly journals Surface Roughness Models and Their Experimental Validation in Micro Milling of 6061-T6 Al Alloy by Response Surface Methodology

2015 ◽  
Vol 2015 ◽  
pp. 1-9 ◽  
Author(s):  
Jie Yi ◽  
Li Jiao ◽  
Xibin Wang ◽  
Junfeng Xiang ◽  
Meixia Yuan ◽  
...  
Keyword(s):  
Surface Roughness ◽  
Response Surface ◽  
Removal Rate ◽  
Micro Milling ◽  
Al Alloy ◽  
Machined Surface ◽  
Contour Map ◽  
Good Surface ◽  
Micro Features ◽  
Good Surface Roughness

Due to the widespread use of high-accuracy miniature and micro features or components, it is required to predict the machined surface performance of the micro milling processes. In this paper, a new predictive model of the surface roughness is established by response surface method (RSM) according to the micro milling experiment of 6061-T6 aluminum alloy which is carried out based on the central composite circumscribed (CCC) design. Then the model is used to analyze the effects of parameters on the surface roughness, and it can be concluded that the surface roughness increases with the increasing of the feed rate and the decreasing of the spindle speed. At last, based on the model the contour map of the surface roughness and material removal rate is established for optimizing the process parameters to improve the cutting efficiency with good surface roughness. The prediction results from the model have good agreement with the experimental results.

Sign in / Sign up

Export Citation Format

Share Document