The Effect of Lashing Wire Location on Mode Localization of Mistuned Bladed Disks

2012 ◽  
Vol 510 ◽  
pp. 160-164
Author(s):  
Ai Lun Wang ◽  
Qiang Huang
Keyword(s):  
Finite Element ◽  
Significant Influence ◽  
Natural Frequencies ◽  
Mode Shapes ◽  
Finite Element Models ◽  
Bladed Disks ◽  
Mode Localization ◽  
Bladed Disk ◽  
Natural Characteristics

The finite element models of bladed disks with different lashing wire locations were established. The natural characteristics and mode shapes of bladed disks with different lashing wire locations were compared, and the effect of lashing wire location on the natural characteristics and mode localization of bladed disks were analyzed. These results show that different lashing wire locations could carry different natural frequencies to bladed disk, and there must be one lashing wire location with the highest frequencies. Lashing wire location has a significant influence on the mode localization of the mistuned bladed disks, and the mode localization of the bladed disks is less sensitive to mistuning when the lashing wire is in the middle of blades.

scholarly journals High-Fidelity Sensitivity Analysis of Modal Properties of Mistuned Bladed Disks Regarding Material Anisotropy

2018 ◽  
Author(s):  
Adam Koscso ◽  
Guido Dhondt ◽  
E. P. Petrov
Keyword(s):  
Sensitivity Analysis ◽  
Finite Element ◽  
Natural Frequencies ◽  
Mode Shapes ◽  
Finite Element Models ◽  
Coordinate Systems ◽  
Bladed Disks ◽  
Bladed Disk ◽  
Material Orientation

A new method has been developed for sensitivity calculations of modal characteristics of bladed disks made of anisotropic materials. The method allows the determination of the sensitivity of the natural frequencies and mode shapes of mistuned bladed disks with respect to anisotropy angles that define the crystal orientation of the monocrystalline blades using full-scale finite element models. An enhanced method is proposed to provide high accuracy for the sensitivity analysis of mode shapes. An approach has also been developed for transforming the modal sensitivities to coordinate systems used in industry for description of the blade anisotropy orientations. The capabilities of the developed methods are demonstrated on examples of a single blade and a mistuned realistic bladed disk finite element models. The modal sensitivity of mistuned bladed disks to anisotropic material orientation is thoroughly studied.

scholarly journals High-Fidelity Sensitivity Analysis of Modal Properties of Mistuned Bladed Disks Regarding Material Anisotropy

2018 ◽  
Vol 141 (2) ◽  
Author(s):  
Adam Koscso ◽  
Guido Dhondt ◽  
E. P. Petrov
Keyword(s):  
Sensitivity Analysis ◽  
Finite Element ◽  
Natural Frequencies ◽  
Mode Shapes ◽  
Finite Element Models ◽  
Coordinate Systems ◽  
Bladed Disks ◽  
Bladed Disk ◽  
Material Orientation

A new method has been developed for sensitivity calculations of modal characteristics of bladed disks made of anisotropic materials. The method allows the determination of the sensitivity of the natural frequencies and mode shapes of mistuned bladed disks with respect to anisotropy angles that define the crystal orientation of the monocrystalline blades using full-scale finite element models. An enhanced method is proposed to provide high accuracy for the sensitivity analysis of mode shapes. An approach has also been developed for transforming the modal sensitivities to coordinate systems (CS) used in industry for description of the blade anisotropy orientations. The capabilities of the developed methods are demonstrated on examples of a single blade and a mistuned realistic bladed disk finite element models. The modal sensitivity of mistuned bladed disks to anisotropic material orientation is thoroughly studied.

A Comparison of Two Finite Element Reduction Techniques for Mistuned Bladed-Disks

2000 ◽  
Author(s):  
François Moyroud ◽  
Torsten Fransson ◽  
Georges Jacquet-Richardet
Keyword(s):  
Finite Element ◽  
Mode Shapes ◽  
Finite Element Models ◽  
Computationally Efficient ◽  
Bladed Disks ◽  
Mode Localization ◽  
Reduced Order ◽  
Bladed Disk ◽  
Reduction Techniques ◽  
Modal Reduction

The high performance bladed-disks used in today’s turbomachines must meet strict standards in terms of aeroelastic stability and resonant response level. One structural characteristic that can significantly impact on both these area is that of bladed-disk mistuning. To predict the effects of mistuning, computationally efficient methods are necessary to make it feasible, especially in an industrial environment, to perform free vibration and forced response analyses of full assembly finite element models. Due to the size of typical finite element models of industrial bladed-disks, efficient reduction techniques must be used to systematically produce reduced order models. The objective of this paper is to compare two prevalent reduction methods on representative test rotors, including a modern design industrial shrouded bladed-disk, in terms of accuracy (for frequencies and mode shapes), reduction order, computational efficiency, sensitivity to inter-sector elastic coupling, and ability to capture the phenomenon of mode localization. The first reduction technique employs a modal reduction approach with a modal basis consisting of mode shapes of the tuned bladed-disk which can be obtained from a classical cyclic symmetric modal analysis. The second reduction technique is based on a Craig and Bampton substructuring and reduction approach. The results show a perfect agreement between the two reduced order models and the non-reduced finite element model. It is found that the phenomena of mode localization is equally well predicted by the two reduction models. In terms of computational cost, reductions from 1 to 2 orders of magnitude are obtained for the industrial bladed-disk, with the modal reduction method being the most computationally efficient approach.

A Comparison of Two Finite Element Reduction Techniques for Mistuned Bladed Disks

2002 ◽  
Vol 124 (4) ◽  
pp. 942-952 ◽  
Author(s):  
F. Moyroud ◽  
T. Fransson ◽  
G. Jacquet-Richardet
Keyword(s):  
Finite Element ◽  
Reduction Technique ◽  
Mode Shapes ◽  
Reduced Order Models ◽  
Bladed Disks ◽  
Mode Localization ◽  
Reduced Order ◽  
Bladed Disk ◽  
Reduction Techniques ◽  
Modal Reduction

The high performance bladed disks used in today’s turbomachines must meet strict standards in terms of aeroelastic stability and resonant response level. One structural characteristic that can significantly impact on both these areas is that of bladed disk mistuning. To predict the effects of mistuning, computational efficient methods are much needed to make free-vibration and forced-response analyses of full assembly finite element (FE) models feasible in both research and industrial environments. Due to the size and complexity of typical industrial bladed disk models, one must resort to robust and systematic reduction techniques to produce reduced-order models of sufficient accuracy. The objective of this paper is to compare two prevalent reduction methods on representative test rotors, including a modern design industrial shrouded bladed disk, in terms of accuracy (for frequencies and mode shapes), reduction order, computational efficiency, sensitivity to intersector elastic coupling, and ability to capture the phenomenon of mode localization. The first reduction technique employs a modal reduction approach with a modal basis consisting of mode shapes of the tuned bladed disk which can be obtained from a classical cyclic symmetric modal analysis. The second reduction technique uses Craig and Bampton substructure modes. The results show a perfect agreement between the two reduced-order models and the nonreduced finite element model. It is found that the phenomena of mode localization is equally well predicted by the two reduction models. In terms of computational cost, reductions from one to two orders of magnitude are obtained for the industrial bladed disk, with the modal reduction method being the most computationally efficient approach.

Experimental Investigation of Mode Localization and Forced Response Amplitude Magnification for a Mistuned Bladed Disk

2000 ◽  
Author(s):  
John Judge ◽  
Christophe Pierre ◽  
Oral Mehmed
Keyword(s):  
Experimental Investigation ◽  
Traveling Wave ◽  
Forced Response ◽  
Response Amplitude ◽  
Mode Shapes ◽  
Bladed Disks ◽  
Element Analysis ◽  
Mode Localization ◽  
Bladed Disk ◽  
Out Of Plane

The results of an experimental investigation on the effects of random blade mistuning on the forced dynamic response of bladed disks are reported. The primary aim of the experiment is to gain understanding of the phenomena of mode localization and forced response blade amplitude magnification in bladed disks. A stationary, nominally periodic, twelve-bladed disk with simple geometry is subjected to a traveling-wave, out-of-plane, “engine order” excitation delivered via phase-shifted control signals sent to piezo-electric actuators mounted on the blades. The bladed disk is then mistuned by the addition of small, unequal weights to the blade tips, and it is again subjected to a traveling wave excitation. The experimental data is used to verify analytical predictions about the occurrence of localized mode shapes, increases in forced response amplitude, and changes in resonant frequency due to the presence of mistuning. Very good agreement between experimental measurements and finite element analysis is obtained. The out-of-plane response is compared and contrasted with the previously reported in-plane mode localization behavior of the same test specimen. This work also represents an important extension of previous experimental study by investigating a frequency regime in which modal density is lower but disk-blade interaction is significantly greater.

scholarly journals Dynamic Response Of Tower Structures

2015 ◽  
Vol 2 ◽  
pp. 85
Author(s):  
Liga Gaile ◽  
Ivars Radinsh
Keyword(s):  
Finite Element ◽  
Structural Changes ◽  
Natural Frequencies ◽  
Resonance Effect ◽  
Dynamic Loads ◽  
Mode Shapes ◽  
Finite Element Models ◽  
Dynamic Parameters ◽  
Vibration Level ◽  
Tower Structure

The present study focuses on the tower type structures response to the dynamic loads. The study analyzes the possible mode shapes regarding to tower structure. The estimation of mode shapes and their dependence from structural changes was made for an existing tower structure. To get an acceptable tower’s vibration level and avoid possibility of resonance effect from usual serviceability loads it was evaluated options to change natural frequencies of the structure. It is performed existing 36m high sightseeing tower dynamic analysis and proposed potential solutions to increase critical natural frequencies of the structure. In this study to obtain dynamic parameters of the sightseeing tower structure have been used finite element models and calculation techniques.

Multistage Coupling of Eight Mistuned Bladed Disk on a Solid Shaft: Part 1—Free Vibration Analysis

2012 ◽  
Author(s):  
Romuald Rzadkowski ◽  
Artur Maurin
Keyword(s):  
Finite Element ◽  
Free Vibration ◽  
Vibration Analysis ◽  
Natural Frequencies ◽  
Free Vibration Analysis ◽  
Free Vibrations ◽  
Rotor Blades ◽  
Mode Shapes ◽  
Bladed Disk ◽  
Centrifugal Stiffening

Considered here was the effect of multistage coupling on the dynamics of a rotor consisting of eight mistuned bladed discs on a solid shaft. Each bladed disc had a different number of rotor blades. Free vibrations were examined using finite element representations of rotating single blades, bladed discs, and the entire rotor. In this study the global rotating mode shapes of eight flexible mistuned bladed discs on shaft assemblies were calculated, taking into account rotational effects such as centrifugal stiffening. The thus obtained natural frequencies of the blade, shaft, bladed disc and entire shaft with discs were carefully examined to discover resonance conditions and coupling effects. This study found that mistuned systems cause far more intensive multistage coupling than tuned ones. The greater the mistuning, the more intense the multistage coupling.

Analysis of the Worst Mistuning Patterns in Bladed Disk Assemblies

2003 ◽  
Vol 125 (4) ◽  
pp. 623-631 ◽  
Author(s):  
E. P. Petrov ◽  
D. J. Ewins
Keyword(s):  
Finite Element ◽  
Large Scale ◽  
Optimization Problem ◽  
Element Model ◽  
Design Parameters ◽  
Finite Element Models ◽  
Bladed Disks ◽  
Bladed Disk ◽  
The Many

The problem of determining the worst mistuning patterns is formulated and solved as an optimization problem. Maximum resonant amplitudes searched across the many nodes of a large-scale finite element model of a mistuned bladed disk and across all the excitation frequencies in a given range are combined into an objective function. Individual blade mistuning is controlled by varying design parameters, whose variation range is constrained by manufacture tolerances. Detailed realistic finite element models, which have so far only been used for analyzing tuned bladed disks, are used for calculation of the forced resonant response of mistuned assemblies and for determination of its sensitivity coefficients with respect to mistuning variation. Results of the optimum search of mistuning patterns for some practical bladed disks are analyzed and reveal higher worst cases than those found in previous studies.

scholarly journals Effects of Bearings and Housing on Mode Localization of a Nearly Cyclic Symmetric System

2016 ◽  
Vol 138 (5) ◽  
Author(s):  
Y. F. Chen ◽  
I. Y. Shen
Keyword(s):  
Finite Element ◽  
Reference System ◽  
Deductive Reasoning ◽  
Mode Shapes ◽  
Symmetric System ◽  
Finite Element Analyses ◽  
Localized Modes ◽  
Mode Localization ◽  
Bladed Disk ◽  
Cyclic Symmetric

This technical brief is to study how flexible bearings and housing affect mode localization of a nearly cyclic symmetric system with mistuning. This study is conducted via finite-element analyses and deductive reasoning. A reference system studied is a bladed disk with two groups of 24 localized modes. When bearings and housing are introduced into the reference system, their presence changes natural frequencies, mode shapes, and the number of the localized modes. Moreover, the mistuning causes bearing forces to surge for all the localized modes. A deductive reasoning based on the existing literature supports the observation from the finite-element analyses.

Method for Analysis of Nonlinear Multiharmonic Vibrations of Mistuned Bladed Disks With Scatter of Contact Interface Characteristics

2005 ◽  
Vol 127 (1) ◽  
pp. 128-136 ◽  
Author(s):  
E. P. Petrov ◽  
D. J. Ewins
Keyword(s):  
Finite Element ◽  
Degrees Of Freedom ◽  
Large Scale ◽  
Forced Response ◽  
Finite Element Models ◽  
Linear Vibration ◽  
Bladed Disks ◽  
Bladed Disk ◽  
Interface Characteristics ◽  
Blade Frequency

An efficient method for analysis of nonlinear vibrations of mistuned bladed disk assemblies has been developed. This development has facilitated the use of large-scale finite element models for realistic bladed disks, used hitherto in analysis of linear vibration, to be extended for the analysis of nonlinear multiharmonic vibration. The new method is based on a technique for the exact condensation of nonlinear finite element models of mistuned bladed disks. The model condensation allows the size of the nonlinear equations to be reduced to the number of degrees of freedom where nonlinear interaction forces are applied. The analysis of nonlinear forced response for simplified and realistic models of mistuned bladed disks has been performed. For a practical high-pressure bladed turbine disk, several types of nonlinear forced response have been considered, including mistuning by (i) scatter of underplatform dampers, (ii) shroud gap scatter, and (iii) blade frequency scatter in the presence of nonlinear shroud interactions.

Sign in / Sign up

Export Citation Format

Share Document